Illumine CLI-EMM023927 Installation Guide
Contents
1.2. inside the outlet box and not pinched between the ceiling cover and the ceiling 02 Screw the two 1 1 4 threaded studs supplied into the tapped holes in the hanger bracket Figure 18 13 Lifi the ceiling cover up to the threaded studs and turn until the studs protrude through the holes in the ceiling cover Figure 18 O4 Position the ceiling cover ring onto the threaded studs and secure both the ceiling cover and ring in place by sliding lockwashers supplied over the threaded studs and installing the two knurled Knobs supplied Figure 18 Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling pene CEILING COVER RING EXTERNAL TOOTH C 8 32 KNURLED KNOB 2 LOCKWASHER 2 Figure 18 Using Your Ceiling Fan Accessories 01 Downrod Extension Kits see store or catalog 12 Ceiling Fan Controls see store or 4 3 2 1 d Figure 19 IMPORTANT Fan installation must be completed including the installation of the fan blades before testing of the controls O 1 Restore electrical power to the outlet box by turning the electricity on at the main fuse box O 2 Check the operation of the fan by sliding the bar of the control through the four positions marked 1 4 0 position is OFF Figure 19 O 3 Ali fans are shipped from the factory with the reversing switch positioned to circulate air downward If airflow is desire
3. TWO Is SCREWS SUPPLIED T SLOT SS zh SLIDE THE HANGER BRACKET ONTO THE OUTLET BOX SCREWS THROUGH THE T SLOT HANGER BRACKET Figure lt o Aa WARNING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplied with outlet box Most outlet boxes commonly used for support of Ilght fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt 4 WARNING Turning off wall switch Is not sufficient To avoid possible electrica shock be sure electricity is turned off at the main fuse box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock NOTE The hanger bracket must be mounted flush with the ceiling in order for the ceiling cover to install properly lf necessary use leveling washers not How to Hang Your Ceiling Fan For Close to the Ceiling Mounting O1 For close to the ceiling mounting the two decorative upper covers must be removed before installation to hanger bracket Figure 14 Carefully lift the fan assembly up to the hanger bracket Pass the hook on the hanger bracket through one of the screw holes not the slots in the ceiling cover Figure 14 The hook must pass from the inside of the ceiling
4. Installing the Ceiling Cover on the Fan Motor Housing For Close to the Ceiling Mounting NOTE The decorative lower cover coupler cover and hanger ball assembly are not needed for close to the ceiling mounting 01 Remove and retain three screws from the top of the motor housing Figure 9 O 2 Position the rubber gasket supplied in parts bag on the motor housing smali holes in gasket cenered over the screw holes in the housing Figure 9 fT REMOVE AND RETAIN Be 3 SCREWS every other one RUBBER GASKET Figure 9 13 Position the ceiling cover onto the top of the motor housing and reattach the three screws previously removed Figure 10 CEILING COVER SCREW 3 RUBBER GASKET Installation of Hanger Bracket 4 WARNING The fan must be hung with at least 7 of clearance from floor to blades Figure 11 A CEILING al AT LEAST T 7 FLOOR Ys Figure 11 a WARNING The outlet box and joist must be securely mounted and capable of supporting at least 35 Ibs Use only a U L outlet box listed as Acceptable for Fan Support C 1 Position the hanger bracket on the outlet box so that the T slots in the hanger bracket are aligned with the outlet box screws Figure 12 NOTE The four hanger bracket screws and lockwashers are included in the parts bag for this fan Must be installed for Dual Mount and NOT used with Downrod standard Mount Slee l S ly LOOSEN
5. cover to the outside The hook will hold the fan assembly while connecting the wiring 4 WARNING The hook must pass through the screw hole in the ceiling cover from the inside to the outside Any other hanging method may cause the hook to break and the fan to fail supplied between the outlet box and 3 Loosely install two M5 x 10mm screws the hanger bracket C12 Slide the hanger bracket onto the outlet box screws Center the bracket over the outlet box and then securely tighten the screws Figure 13 ow m _ SECURELY TIGHTEN HOOK SCREWS HANGER Figure 13 BRACKET 4m WARNING Hanger bracket must seat firmly against outlet box If the outlet box Is recessed remove wall board until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or fall and lockwashers supplied in hanger bracket at this time The remaining two lockwashers and screws will be installed after the ceiling fan is hung Figure 14 HOOK ON HANGER BRACKET MUST PASS THROUGH SCREW HOLE IN CEILING COVER INSIDE OF MS x 10mm SCREW AND LOCKWASHER 2 each CEILING COVER FAN HOUSING DECORATIVE UPPER COVER 2 Figure 14 How to Hang Your NOTE Make all wiring connections using Pe wire connectors supplied Make sure Ceiling Fan For that all connections are tight including Standard Mounting ground and that no bare wire is visible at the wire connecto
6. d in opposite direction turn your fan OFF and wait for the blades to stop turning then slide the reversing switch to the opposite position and turn fan on again Figure 20 O 4 The fan blades will turn in the opposite direction and reverse the airflow Reverse Switch Information Season Rotation Direction Switch Position Summer Counter Clockwise Right Winter Clockwise Left REVERSING SWITCH Figure 20 catalog 3 Light Kits see store or catalog 44 WARNING The use of any other contro not specifically approved for this fan could result in flre shock and personal injury a WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage Maintenance IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed When cleaning use only a soft brush or lint free cloth to avoid scratching the finish Abrasive cleaning agents are not required and should be avoided to prevent damage to finish 4 WARNING Do not use water when cleaning your ceiling fan It could damage the motor or the blades and create the possibility of an electrical shock
7. hanger bracket and proceed as follows O 1 After connections have been made turn leads upward and carefully push leads into the outlet box with the green equipment grounding conductor and white grounded neutral conductor on one side of the outlet box and the black and blue ungrounded conductors on the other side of the outlet box g 2 Lift the ceiling cover up to the hanger bracket Engage the slots in the ceiling cover with the loosened screws in the bracket and turn the cover counter clockwise Figure 17 Be sure that the lockwashers are between the screw heads and the ceiling cover 3 Install the remaining two lockwashers and screws supplied tighten all four screws securely 44 WARNING To avoid possible fire or shock make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling INSTALL SCREW 7T AND LOCKWASHER CEILING l T y TIGHTEN D SCREW lA FAN HOUSING 77 Figure 17 Installation of Ceiling Cover For Standard Mounting C1 After connections have been made turn leads upward and carefully push leads into the outlet box with ihe green equipment grounding conductor and white grounded neutral conductor on one side of the outlet box and the black and blue ungrounded conductors on the other side of the outlet box 44 WARNING To avoid possible fire or shock make sure that the electrical wires are completely
8. low Aviat the installation instruction of the accessory control if used 4 After connections have been made turn leads upward and carefully push leads into the outlet box with the white TAB GROOVE Figure 15 How to Wire and green leads on one side of the igi outlet box and the black and blue ieads Your Ceiling Fan on the other side of the outlet box If you feel that you do not have enough BLUE FAN WIRE electrical wiring knowledge or experience have your fan installed by a licensed electrician 4 WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity Is turned off at the main fuse GROUND WIRE FROM HANGER BRACKET box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be FAN WIRE properly grounded as a precaution WHITE SUPPLY against possible electrical shock NEUTRAL WHITE FAN WIRE BLACK GREEN GROUND WIRE FROM HANGER BALL Figure 16 10 f A WARNING Check to see that all connections are tight including ground and that no bare wire Is visible at the wire connectors except for the ground wire Do not operate fan until blades are in place Noise and fan damage could result Installation of Ceiling Cover For Close to the Ceiling NOTE When installing the ceiling fan using the close to the ceiling method carefully lift the fan assembly from the hook on the
9. rs except for the O 1 Carefully lift the fan assembly and seat ground wire the hanger ball in the hanger bracket 1 1 Connect the green grounding lead from Figure 15 The tab on the hanger the hanger ball and the green bracket must seat in the groove in the grounding lead from the hanger bracket hanger ball to the grounding conductor of supply ania See Sane this may be a bare wire or wire with Ze WARNING ioe green colored insulation Securely connect wires with wire connectors Failure to seat tab In groove could cause supplied damage to electrical wires and possible shock or fire hazard NOTE When wiring the ceiling fan for close to the ceiling mounting there will be no green grounding lead from WARNING the hanger ball NOTE If you are using an Emerson To avoid possible fire or shock do not pinch Light Fixture with your fan see Light wires between the hanger ball downrod Fixture Owner s Manual for wiring pesembry and Hanger black O2 Securely connect the fan motor white wire to the supply white neutral wire using wire connector supplied Figure 16 Securely connect the fan motor black wire to the supply black hot wire using wire connector supplied Figure 16 O13 If a downlight is not being installed cap the blue wire using a supplied wire HANGER connector If a downlight is being BRACKET installed a separate hot supply must be available of an optional Emerson accessory control must be used Fol
Download Pdf Manuals
Related Search