Yosemite Home Decor WHITNEY-BBN-1 Installation Guide
Contents
1. is tightened against downrod locknut should then be tightened against connector yoke Repeat for both Fig 7 LOCK PLN 5 MOTOR J SETSCREW MOTOR SETSCREW 3 Tighten motor setscrew Check the strenght of this connection pre tightened at factory by holding the motor housing in position and tuming the downrod counter clockwise If this connection slips retighten motor setscrew and locknut Follow the sarne procedure and mentioned above for downrod setscrews 4 install ball into hanger bracket opening The tab opposite of the hanger bracket opening should fit in siot on bail Fig 8 Fig 8 Bail Slot 5 Make wire connections Refer to section titled Electrical Connections 6 Slide canopy up and fasten to hanger bracket with the 4 screws provided WARNING To avoid damaging the blade arms and blades go not instail either until fan is fastened to ceiling To avord motor shift nandle tan by downrodg or switch housing only affine2. Owner s Manual CONGRATULATIONS You have chosen the best Your new ceiling fan will 1 SAFETY TIPS To avoid possible electric shock tum off the electricity at the main fuse box or circuit panel before you begin the fan installaton or before servicing the fan or installing acces sones UNPACKING YOUR FAN Unpack your fan and check the contents Do not discard the carton If warranty replacement or repair is ever necessary the fan should be retumed in onginal packaging Remove ali parts and hardware Do not lay motor housing on its side provide you with many years of comfort and satisfaction 2 Read all instructions and safety information carefully before installing your fan and the decorative casing may shift save these instructions 2 Examine all parts You should have the following 3 Make sure all electrical connections comply with local codes or ordinances and the National TABLE OF CONTENTS Electrical Code if you are unfamiliar with electric wiring please use a qualified and licensed electrician 4 Make sure you have a location selected for your fan that allows clear space for the blades to rotate oe Your Fan and at least seven 7 feet of clearance between the floor and the fan blade tips The fan should Tool d Materials Required 4 be mounted at least thirty 30 inches from walls or other upright structures Oo and Marar qu 5 WARNING The
3. Washers 10 sets are already in fan motor NOTE The important safety precautions and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur It must be understood that common sense and caution are necessary factors in the installation and operation of this fan TOOLS AND MATERIALS REQUIRED Phillips screw driver Blade screw driver x Adjustable pliers or wranch Step Ladder Wire cutter Electrical tape NADAO ELECTRICAL OUTLET BOX If there is an existing outlet box ensure itis UL listed and clearly marked Suitable for Fan Support If not it must be replaced with an approved one 2 Secure the outlet box or make sure the existing box is secured directly to the building structure Use appropriate fasteners and building materials Wood joist and outlet box must be able to supporta minimum of 50 pounds 3 Figures 1 2 and 3 are examples of different ways to mount the outlet box in differ ent situations A longer downrod may be required in sloped ceiling situations to maintain proper blade clearance To hang the fan in locations where no ceiling joist is available a hanger support bar may ve required Fig 4 Fig 1 Fig 2 gt M Qutiet Box Fig 3 Fig 4 Provide Strong Support Ceiling Pre a Reewssed Mounting Outlet Box P praa Outlet Box aie INSTALL HANGER BRACKET To avoid possible electrical sho
4. ck be sure electricity is turned off at the main power panel before wiring All wiring must be in accordance with National and Local Electrical Codes andthe ceiling fan must be grounded as a precaution against possible electrical shock 2 Attach hanger bracket to outlet box using screws provided with the outlet box Fig 5 Install square rubber washers between bracket and outlet box to reduce vibration of metal to metal surfaces ELECTRICAL OUTLET BOX RUBBER WASHER HANGER BRACKET SPRING WASHER SCREW CAUTION Electrical box must be wired to U L general use wall switch To reduce the risk of injury turn off power at wall switch or main fuse or circuit breaker before attempting installation or servicing WARNING To avoid fire or shock follow all wiring instructions carefully Any electrical work not described in these instructions should be done or approved by a licensed electrician WARNING To reduce the risk of fire Electric shock or personal injury mount to outlet box marked acceptable for fan support and use mounting screws provided with the outlet box Most outlet boxes commonly used for the support of lighting fixtures are not acceptabie for fan support and may need to be replaced Consult a quatified electrician if in doubt 5 1 INSTALLING THE FAN SELECT TYPE OF INSTALLATION HUGGER HANG DOWN This method is preferred if maximum headroom is require
5. d The ceiling must be horizontal not sloped This method is preferred if the ceiling is sloped or vaulted or if ceiling is extra high requiring the use of a downrod WARNING The fan must be hung with at least 7 of clearance from floor to blades HANG DOWN STYLE Slide the canopy on the downrod Fig 6 Thread the power leads from the fan through the canopy and downrod Take extra care not to pull power wires damage and loose connections could result from any abnormal pressure on these wires Set downrod into yoke Rotate until the holes match Be careful notto damage wiring insert connector pin through the holes See Fig 6A 6B Secure the pin by inserting the stop pin through the connector pin Fig 6 Fig 6A POWER LEADS Downrod Boil Collar Yoke DOWNROO DANOPY Fig 68 Connector y Pin be A Stop Pin DECORATIVE etmi CANOPY BOTTOM COVER WARNING Do not force connector pin through downrod Use of force couid cause aamage to wires inside Make sure tne stop pin is properly engaged to prevent t from falling out Failure to properly install locking pin as noted could result in fan loosening and possibly falling 6 2 Tighten the two downrod setscrews Some models have locknuts for the setscrew to ensure the setscrews fully seat against the downrod itis necessary to back off the locknut until it contacts the setscrew head prior to tightening the setscrew When setscrew
6. ee pcs 4 9 After making electrical connections spliced conductors should be turned upward and pushed d A 3 3 te 5 2 i D u al M ount C el l 1 ng Fan carefully up into outlett box The wires shouid be spread apart with the grounded conductor 6 tee nng Assembly i S 12 Extra Switch Cap t piece and the equipment graunding conductor on one side of the outlet box P 5 Blades 1 Li ght 10 WARNING To reduce the risk of electrical shock and fire do not use this fan with any solid Ata ary eas state fan speed control device or rheostat Extra Blade Screw and Fibre Washer set 11 Do not operate the reverse switch until the fan has come to a complete stop b Pull Chain Fob 2sats 12 Do not insert anything into the fan blades while they are rotating Hanger Bracket Hardware and Extra screw 13 WARNING To reduce the risk of personal injury do not bend the blade brackets also referred Cee tlie iri Scraw and Spring Washer at e Assembly amp Installation e Operation to as flanges during assembly or after installation Do not insert objects in the path of the blades 14 To avoid personal injury or damage to the fan and other items be cautions when working around or cleaning the fan 15 Donotuse water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning Extra Yoke Screws and Spring Washer For Hugger Style Use 3 sets Note Blade Arm Screws and Spring
7. outlet box and ceiling support joist used must be securely mounted and Electrical Outlet Box 4 capable of supporting at least 50 pounds To reduce the risk of fire electric shock or Install Hanger Bracket 5 personal injury mount to the outlet box marked acceptable for fan supported and use dee the Fan 6 mounting screws provided with the outlet box The box must be supported directly by the j ectrical Connections 9 building structure air tivserutt Blade Attachment 10 6 WARNING To reduce the risk of fire electric shock or personal injury mount to outlet box Installing Light Kit 4 marked acceptable for fan support and use mounting screws provided with the outlet box Operation 12 most outlet boxes commonly used for the support of lighting fixtures are not acceptabie for i fan support and may need to be replaced Consulta qualified electrician it in doubt Trouble Shooting 13 bribe Maintenance 14 7 Electrical diagrams are for reference only Light kits that are not packed with the tan must be U L listed and marked suitable for use with the model fan you are installing Switches must 1 Hanger Bracket 1 Glass Shade 1 piece be U L general use switches Refer to the instructions packaged with the light kits and 2 Canopy 8 DecorativeCup 1 piece switches for proper assembly 3 Canopy Bottom Cover 9 BladeArm 1 set 5 pes l 8 Atter Installation is complete check that all connections are absolutely secure a AO MOEA 10 SaD i Ki 1 s
Download Pdf Manuals
Related Search