Illumine CLI-EMM027420 Installation Guide
Contents
1. Aa WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity Is turned off at the maln fuse box before wiring All wiring must be in accordance wlth National and Local Codes and the ceiling fan must be properly grounded as a precaution agalnst possible electrical shock To avold possible fire or shock do not pinch wires between the hanger ball downrod assembly and hanger bracket Wiring The Ceiling Fan if you feel that you do not have enough electrical wiring Knowledge or experience have your fan installed by a licensed electrician To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring NOTE If you are not sure if the outlet box is grounded contact a licensed electrician for advice as it must be grounded for safe operation 1 Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply this may be a bare wire or wire with green colored insulation Figure 9 Securely connect wires using wire connectors supplied NOTE When wiring the ceiling fan for close to the ceiling mounting there will be no green grounding lead from the hanger ball C 2 Securely connect the fan motor white wire to the 7 supply white neutral wire using wire connector supplied Figure 9 Securely connect the fan motor black wire and blue wire to2. 4 WARNING in a small container to keep them from being lost Do not Install or use fan if any part is damaged or If any parts are missing contact your local missing retailer or catalog outlet for replacement before proceeding Remove the fan housing assembly from the protective plastic bag Turn the upper styrofoam pad over and carefully place the fan motor 4 WARNING assembly into the recess in the pad with the top of This product is designed to use only those parts the motor facing up supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage A FAN MOTOR parts ASSEMBLY NOTE If you are uncertain of part description refer to exploded view illustration MEDIUM BASE Fan motor assembly BULBS 3 or 4 Five fan blades One ceiling cover Five blade flanges One hanger ballAdownrod assembly One hanger bracket One switch housing cover Nar HANGER BALL a Glass shades 3 or 4 if ea CELING 13W E26 Medium Base CFL 3 or 4 CO ASSEMBLY SE One loose parts bag containing Oaea CH Holata 1 Sixteen M5 x 6 washer head blade screws One rubber gasket Two wood pendants Two couplings Three wire connectors One clevis pin One hairpin clip One Phillips round head f
3. 3 are 42 long Measure up approximately 6 to 9 inches above top of hanger ball downrod 4 The fan comes with blue black and white leads assembly Cut off excess leads and strip back that are 42 long Measure up approximately 6 to insulation 1 2 inch from end of leads 9 inches above the motor coupling Cut off excess leads and strip back insulation 1 2 inch from ends 4 of leads NOTE The hanger bracket must be mounted flush with the ceiling in order for the ceiling cover to install properly If necessary use leveling washers not supplled between the outlet box Installing The Hanger Bracket A WARNING The fan must be hung with at least 7 of clearance from floor to blades Figure 4 7 MIN anes i FLOOR The outlet box and joist must be securely mounted and capable of supporting at least 50 Ibs Use only a U L outlet box listed as Acceptable for Fan Support 1 Unscrew but do not remove the two mounting screws in the outlet box Figure 5 Position the hanger bracket on the outlet box so that the T slots in the hanger bracket are aligned with the outlet box screws m m n M w er m gt LOOSEN TWO 2 SCREWS SUPPLIED WITH OUTLET BOX SLIDE THE HANGER BRACKET ONTO THE OUTLET BOX SGREWS THROUGH THE T SLOT HANGER BRACKET Figure 5 4 WARNING To reduce the risk of fire electrical shock or personal injury mount fan to outlet box marked Acceptab
4. balancing the blades or cleaning the fan Do not insert foreign objects between rotating fan blades Installing The C 1 Make sure the three rubber grommets are firmly a oy seated on each of the blade flanges Then mount Ceiling Cover the blade flanges to the fan blades using three M5 x 6 washer head blade screws per blade 1 Remove the left screw and lockwasher from each Figure 11 side of the hanger bracket Figure 10 and loosen the other two screws Mo x 6 WASHER g HEAD BLADE SCREW 3 Per Blade lockwashers are between the screw heads and the ceiling cover NOTE When installing the ceiling fan using the close to the ceiling method carefully lift the fan FAN BLADE assembly from the hook on the hanger bracket b and proceed as follows amp E 2 Lift the ceiling cover up to the hanger bracket Engage the slots in the ceiling cover with the S loosened screws in the bracket and turn the cover counterclockwise Figure 10 Be sure that the ALIGNMENT POST BLADE FLANGE 3 Install the other two screws and lockwashers tighten all screws securely Figure 11 2 Mount one blade assembly to the motor hub by Removal Of The mating the alignment post Figure 11 of the flange with one of the alignment slots in the motor hub Light Fixture Figure 12 Then tighten the two captive screws in the flange to secure the flange to the motor hub NOTE In some instances it may be desirable to Repeat this procedure for the other
5. four blade install the ceillng fan without the light fixture If assemblies Make sure all screws are tightened this is the case proceed as follows You may MOTOR HUB want to keep the Ilght fixture for possible future use a 1 Remove and retain the three screws securing the J light fixture to the switch housing Fixture 14 Remove and retain two wire connectors and Zoe disconnect the light fixture from the switch ae housing SWITCH HOUSING LIGHT FIXTURE 6 SS SCREW 3 BLADE FLANGE SCREW 2 oe Figure 12 Installing The Glass Shades and Light Bulbs a 2 Use the wire connectors to securely cap the each A of the two wires in the switch housing Figure 15 1 To install the glass shade squeeze the retaining clips towards the bulb socket and slide on the C 3 Position the switch housing cover supplied on the glass shade Figure 13 The spring clips will seat switch housing so that the notch in the cover the shade and secure it in place clears the reversing switch Install the three screws 7 2 Instali a 13W E26 medium base bulb CFL in each a PACHI We Covet of the light fitter sockets n WARNING To avoid possible fire or shock do not pinch wires between the hanger ball downrod assembly and hanger bracket Figure 14 SWITCH HOUSING E 3 To remove the shade first remove the light bulb from the socket then simply pull the shade off bisconnecr swo RR ROU COVER using a twistin
6. least 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a quailfled electrician if in doubt 4 The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance for an 8 foot ceiling 5 The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades 6 Follow the recommended instructions for the proper method of wiring your ceiling fan If you do not know enough about electrical wiring have your fan Installed by a licensed electrician NOTE The CF711 fan is sultable for use with solid state speed controls WARNING To avoid fire shock or injury do not use an Emerson or any other brand of control not specifically approved for this fan WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use this product by Emerson Electric Co could result in personal injury or property damage WARNING To Reduce the risk of personal Injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades WARNING To reduce the risk of electrical shock this fa
7. the supply black hot wire using wire connector supplied Figure 9 After connections have been made turn leads upward and carefully push leads into the outlet box with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box REMOVE THIS SCREW AND LOGKWASHER CEILING COVER BLACK SUPPLY HOT Figure 10 To avoid possible fire or shock make sure that the electrical wires are completely Inside the outlet box and not pinched between the ceiling cover and the ceiling GREEN GROUND BLUE WIRE FROM HANGER FAN WIRE BRACKET 4 Cut the speed control switch pull chain and the AN light switch pull chain to the desired lengths ANY EEN GROUN FAN WIRE Ys H FROM HANGER Connect the wood pendants supplied to the pull BALL chains by sliding the pendants small hole first onto the pull chains Then attach the chain couplings supplied to the end of the chains and allow the pendants to fall down over the couplings WHITE SUPPLY NEUTRAL WHITE FAN WIRE Figure 9 4 WARNING Installing The Fan Blades Check to see that all connections are tight Including A WARNING ground and that no bare wire is visible at the wire To reduce the risk of personal injury do not bend the connectors except for the ground wire Do not operate fan until blades are in place Noise and fan damage could result blade flanges when installing the flanges
8. READ AND SAVE THESE INSTRUCTIONS 4 WARNING WARNING To avoid fire shock and serious personal Injury follow these instructions Safety Instructions 1 Read your owner s manua carefully and keep it for future reference 2 Before servicing or cleaning unlit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel 3 Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing 4 Do not put anything into the fan blades while they are turning 5 Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions for Installation 1 To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades 2 All wiring must be in accordance with the National Electrical Code ANSVNFPA 70 2008 and Local Electrical Codes Use the National Electrical Code if Local Codes do not exist The celllng fan must be grounded as a precaution against possible electrical shock Electrical installation should be made or approved by a licensed electrician The outlet box and Joist must be securely mounted and capable of reliably supporting at
9. g Cover Installed on the Motor Housing J 1 Carefully lift the fan assembly up to the hanger bracket Pass the hook on the hanger bracket Figure 7 through one of the screw holes not the slots in the ceiling cover Figure 8 The hook must pass from the inside of the ceiling cover to the outside The hook will hold the fan assembly while connecting the wiring A WARNING The hook must pass through the screw hole in the ceiling cover from the inside to the outside Any other hanging method may cause the hook to break and the fan to fall HOOK ON HANGER BRACKET MUST PASS THROUGH SCREW HOLE IN CEILING COVER INSIDE OF BRACKET FO OUTSIDE OF BRACKET CEILING COVER Figure 8 lf Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds A WARNING To reduce the risk of fire electrical shock or personal injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electriclan if in doubt If your fan is to replace an existing ceiling light fixture turn electricity off at the main fuse box at this time and remove the existing light fixture
10. g motion WIRES FROM LIGHT AON FIXTURE AND SECURELY GAP WITH WIRE CONNECTORS ED Ly Figure 15 SQUEEZE ETAINI CLIPS RETAINING TOGETHER CLIP AND SLIDE ON GLASS i SHADE 13W E26 MEDIUM BASE BULB CFL 3 or 4 GLASS SHADE Figure 13 1 esl a Using Your Ceiling Fan Restore electrical power to the outlet box by turning the electricity on at the main fuse box Check the operation of the light by gently pulling on the light switch pull chain Check the operation of the fan by gently pulling on the speed control switch pull chain The operation sequence is as follows ist pull High 2nd pull Medium 3rd pull Low 4th pull OFF Your fan is shipped from the factory with the reversing switch positioned to circulate air downward if airflow is desired in opposite direction turn the fan off and wait for the blades to stop turning then slide the reversing switch to the opposite position and turn the fan on again The fan blades will turn in the opposite direction and reverse the airflow SPEED CONTROL PULL CHAIN SWITCH REVERSING SWITCH LIGHT PULL CHAIN SWITCH
11. gh the hanger centered over the screw holes in the housing ball downrod assembly Figure 2B 3 Loosen the two setscrews in the motor coupling Align the clevis pin holes in the downrod with the holes in the motor coupling Install the clevis pin and secure with the hairpin clip Figure 1 The clevis pin must go through the holes in the motor coupling and the holes in the downrod Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin The pee clip must be propsrly installed to prevent the clevis pin from working loose Pull on the hanger ball to make sure the clevis pin is Figure Pa ea ASIME ORE properly installed g Figure 2B 3 Gently pry the decorative cap Figure 1 from the A WARNING E ceiling cover Align the holes in the ceiling cover It is critical that the clevis pin in the motor coupling with ie ee in the motor housing and secure is properly installed and the setscrews securely using the three screws Figure 3 tightened Failure to verify that the pin and setscrews are properly installed could result in the fan falling 4 While pulling up on the hanger ball securely tighten the two setscrews in the motor coupling RUBBER Figure 1 panel NOTE The setscrews must be properly installed as described above or fan wobble could result 5 The fan comes with blue black and white leads that Figure
12. lange screw 3 Je HANGER BRACKET or 4 Tw oom Oooo aya BLADES D BLADE FLANGES 2 On om ol OMD HANGER IMPORTANT DECORATIVE ASSEMBLY m CAP Your ceiling fan is designed to be instalied CEILING either in the standard manner or in the cP af COVER close to the celling manner Using the ad BETERE standard method the hanger ball downrod assembly will suspend the fan several inches below the ceiling cover Using the close to the celling method the ceiling cover installs directly on the fan motor housing CLEVES PIN thus mounting the fan 3 1 2 inches closer to the ceiling than the standard method In no case should the fan blades be lower than seven feet above the floor Depending on your desired mounting method proceed to INSTALLING HANGER BALL DOWNROD ASSEMBLY for standard mounting or to INSTALLING CEILING COVER ON FAN MOTOR HOUSING for close to the ceiling mounting Figure 4 OTP Installing The Hanger Installing The Ceiling Cover Ball Downrod Assembly On The Fan Motor Housing For Standard Mounting For Close to the Ceiling Mounting 1 Pass the 42 motor leads through the opening in C 1 the ceiling cover Be sure the cover is oriented i correctly Remove and retain three screws from the top of the motor housing Figure 2A i 2 Positi ied i C 2 Separate untwist and unkink the three motor z he e ea mel ar Peepers leads Route the motor leads throu
13. le for Fan Support and use screws supplied with outlet box Most outlet boxes commonly used for support of Ilght fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt and the hanger bracket C 2 Slide the hanger bracket onto the outlet box screws Center the bracket over the outlet box and then securely tighten the screws Figure 8 4 WARNING Hanger bracket must seat firmly against outlet box If the outlet box is recessed use leveling washers between the hanger bracket and the outlet box until the bracket Is flush with the ceiling If bracket and or outlet box are not securely attached the fan could wobble or fall SECURELY TIGHTEN SCREWS Figure 6 Hanging The Ceiling Fan Standard Method Using Hanger Ball Downrod Ba oy Ct Carefully lift the fan assembly and seat the hanger ball in the hanger bracket Figure 7 The tab on the hanger bracket must seat in the groove in the hanger ball Failure to seat tab In groove could cause damage to electrical wires and possible shock or fire hazard To avoid fire or shock do not pinch wires between the hanger ball downrod assembly and hanger bracket Ta e Tm snore T HANGER HOOK BRACKET bis HANGER GROOVE BALL NOTE CEILING COVER SUPPLY WIRES AND FAN WIRES OMITTED Figure 7 FOR CLARITY Hanging The Ceiling Fan Close to the Ceiling Method with Ceilin
14. n must be installed with an Isolating wall control switch 3 DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep it in a safe place for future use 1 Check to see that you have received the following This Manual is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One stepladder Installed Wire Length Wire Size A W G One 1 4 blade screwdriver One wire stripper Up to 50 ft 14 Three wire connectors supplied 50 100 ft 12 Four 13W E26 medium base bulbs CFL CF711 Three 13W E26 medium base bulbs CFL CF710 MATERIALS Ee Before assembling your ceiling fan refer to section on Wiring outlet box and box connectors must be of type proper method of wirlng your fan page 6 If you feel required by the local code The minimum wire would you do not have enough wirlng knowledge or be a 3 conductor 2 wire with ground of the following experience have your fan installed by a licensed size electrician Unpacking Instructions For your convenience check off boxes are provided next to each step As each step is completed place a check mark in the box This will insure that all steps have been completed and will be helpful In finding your piace should you be interrupted NOTE Place the parts from the loose parts bags
Download Pdf Manuals
Related Search