Illumine CLI-EMM022409 Installation Guide
Contents
1. do not pinch wires between the hanger ball downrod assembly and hanger bracket Installing The Hanger Bracket A WARNING The fan must be hung with at least 7 of clearance from fioor to blades Figure 9 ne MIN 7 TFT FLOOR OLD OSS EES 77 Figure 9 A WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 Ibs Use only a U L outlet box listed as Acceptable for Fan Support A WARNING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box Figure 10 WARNING Hanger bracket must seat firmly against outlet box If the outlet box is recessed remove wall board until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or fall mk OUTLET LER ie BOX SUPPLIED WITH OUTLET BOX HANGER BRACKET Figure 10 I 2 Carefully lift the fan and seat the hanger ball downrod assembly on the hanger bracket that was just attached to the outlet box Figure 11 Be sure the groove in the ball is fined up with2. isolating wall control switch DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep it in a safe place for future use This Manual Is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One 1 4 blade screwdriver One stepladder One wire stripper MATERIALS Wiring outlet box and box connectors must be of type required by the local code The minimum wire shall be a 3 conductor 2 wire with ground of the following size Wire L Wire Size AW G Up to 50 ft 14 50 100 ft 12 WARNING Before assembling your ceiling fan refer to sectlon on proper method of wiring your fan page 7 If you feel you do not have enough wiring knowledge or experlence have your fan Installed by a licensed electrician Unpacking Instructions For your convenience check off boxes are provided next to each step As each step is completed place a check mark in the box This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted 44 WARNING Do not install or use fan if any part is damaged or missing i Aa WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerso
3. leads through the opening in the ceiling cover Be sure the cover is oriented correctly 2 Separate untwist and unkink the three motor leads Route the motor leads through the hanger ball downrod assembly 3 Loosen the two setscrews in the motor coupling Align the clevis pin holes in the downrod with the holes in the motor coupling Install the clevis pin and secure with the hairpin clip Figure 1 The clevis pin must go through the holes in the motor coupling and the holes in the downrod Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin The hairpin clip must be properly installed to prevent the clevis pin from working loose Pull on the hanger ball to make sure the clevis pin is properly installed 4s WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tightened Failure to verify that the pin and setscrews are properly installed could result in the fan falling 4 While pulling up on the hanger ball securely tighten the two setscrews in the motor coupling Figure 1 NOTE The setscrews must be properly Installed as described above or fan wobble could result 5 The fan comes with blue black and white leads that are 42 long Measure up approximately 6 to 9 inches above top of hanger ball downrod assembly Cut off ex
4. READ AND SAVE THESE INSTRUCTIONS EE 52 Ceiling Fan Owner s Manual WARNING WARNING To avoid fire shock and serlous personal injury follow these instructions Safety Instructions Read your owner s manual carefully and keep It for future reference Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing Do not put anything into the fan blades while they are turning Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions for Installation To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades The installation is to be in accordance with the National Electrical Code ANSI NFPA 70 1999 and Local Electrical Codes Use the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution against possible electrical shock Electrical Installation should be made or approved by a licensed electrician The outlet box and joist must be securely mounted and capable of reliably s
5. al injury or property damage Securely connect the fan motor white wire to the supply white neutral wire using wire connector supplied Figure 12 Securely connect the fan motor black wire and blue wire to the supply black hot wire using wire connector supplied Figure 12 After connections have been made turn leads upward and carefully push leads into the outlet box with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box 2 D NOTE CEILING COVER FAN WIRES o BLUE OMITTED FOR CLARITY GROUND 8 uir WIRE LISTED WHITE SUPPLY CONNECTOR 3 NEUTRAL GROUND FROM WHITE FAN ANGER BRACKET WIRE GREEN WIRE Hon SUPPLY i GROUND FROM Figure 12 her Hin mk 4 5 6 A WARNING Check to see that all connections are tight including ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan until blades are In place Noise and fan damage could result Screw the two threaded studs supplied into the tapped holes in the hanger bracket Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover Figure 13 Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs supplied Figure 13 Tighten the knurled knobs securely until the ceiling cover fit
6. cess leads and strip back insulation 1 2 inch from end of leads HANGER BALL D DECORATIVE pe OWNROD CAP CEILING HAIRPIN CLIP a COVER SETSCREW a Me enne a ET Wise SS LEV MOTOR COUPLING T ED e A i gt Cf SETSCREW WS Figure 1 M5 x 6mm washer head blade screws per blade Figure 2 4m WARNING To reduce the risk of personal Injury do not bend the blade flanges when Installing the flanges balancing the blades or cleaning the fan Do not insert foreign objects between rotating fan blades M5 x 6mm WASHER ga HEAD BLADE SCREW 3 Per Blade FAN BLADE D ae BLADE FLANGE Figure 2 NOTE Take care not to scratch fan housing when installing blades NOTE Remove and discard the three shipping spacers and screws from the motor hub 7 Turn the fan assembly upside down in preparation for mounting the fan blade assemblies 8 Rotate the motor hub until the flange screw hole is next to the cutout in the switch housing plate Attach the blade assembly to the motor hub using the two M6 x 12mm flange head screws and lockwashers Figure 3 Make sure all screws are tightened Repeat this procedure for the other four blade assemblies SWITGH HOUSING BLADE FLANGE PLATE PSE BS SS IKK A SANE MOS S INES m ID lt gt A5 es AN Ps Lis g 5 ay M6 x 12mm FLANGE HEAD C MOTOR HUB C c SCREWS WITH LOCKWASHERS Oy Oi INNS Figure 3 Remove the center pl
7. h chain from touching the light bulbs 19 Install pendants onto light fixture chain and fan switch chain using couplings provided NOTE It is advisable to periodically check the tightness of the finial 20 You have now completed the assembly of your new ceiling fan You can now proceed with hanging and wiring your fan Electrical Requirements Your new ceiling fan will require grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds A WARNING To reduce the risk of fire electrical shock or personal injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplied with outlet box Most outlet boxes commonly used for support of Sight fixiures are not acceptable for fan support and may need to be replaced Consult a qualified electrician If in doubt If your fan is to replace an existing ceiling light fixture turn electricity off at the main fuse box at this time and remove the existing light fixture 4 WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity Is turned off at the maln fuse box before wiring All wiring must be in accordance with National and Local Codes and the ceiling fan must be properly grounded as a precaution agalnst possible electrical shock A WARNING To avoid possible fire or shock
8. n Electric Company Substitution of parts or accessories not designated for use with this product by Emerson Electric Company could result in personal injury or property damage 1 Check to see that you have received the following parts NOTE If you are uncertain of part description refer to exploded view illustration Fan motor assembly Five fan blades One ceiling cover Five blade flanges One hanger ball downrod assembly One hanger bracket One switch housing assembly Two 60 watt candelabra bulbs One light fitter One glass bowl One loose parts bag containing 1 Sixteen M5 x 6mm washer head blade screws Two threaded studs 8 32 x 1 1 4 Two lockwashers 8 32 Two knurled knobs 8 32 Two wood pendants Two couplings Three wire connectors One clevis pin AT TSA 0 On DOB GN 9 One hairpin clip 10 Eleven M6 x 12mm flange head screws with lockwashers NOTE Place the parts from the loose parts bags in a small contalner to keep them from being lost If any parts are missing contact your local retailer or catalog outlet for replacement before proceeding 2 Remove the fan housing assembly from the protective plastic bag Turn the upper styrofoam pad over and carefully place the fan motor assembly into the recess in the pad with the top of the motor facing up How to Put Your Ceiling 6 Mount the blade flanges to fan blades using three Fan Together 1 Pass the 42 motor
9. n the opposite direction and reverse the airflow if SPEED CONTROL LIGHT PULL Pa PULL CHAIN SWITCH CHAIN SWITCH
10. s snugly against the ceiling and the hole in the ceiling cover is clear of the downrod Your fan is now wired to be turned on and off from the fan switch CEILING COVER THREADED STUD KNURLED KNOB Figure 13 4 WARNING To avoid possible fire or shock make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling Cut the 3 speed switch pull chain to a desired length optional Connect the wood pendant supplied to the 3 speed switch pull chain by sliding the wooden pendant small hole first onto the pull chain Attach the chain coupler to the end of the chain and allow the wooden pendant to fall down over the coupling le ale Mis Using Your Geiling Fan Restore electrical power to the outlet box by turning the electricity on at the main fuse box Check the operation of the light by gently pulling on the light switch pull chain Check the operation of the fan by gently pulling on the speed control switch pull chain The operation sequence is as follows tst pull High ard pull Low 2nd pull Medium 4th pull OFF Your fan is shipped from the factory with the reversing switch positioned to circulate air downward If airflow is desired in opposite direction turn the fan off and wait for the blades to stop turning then slide the reversing switch to the opposite position and turn the fan on again The fan blades will turn i
11. tab on the hanger bracket Figure 11 A WARNING Faliure to seat tab In groove could cause damage to electrical wires and possible shock or fire hazard NOTE CEILING COVER SUPPLY WIRES AND FAN WIRES OMITTED OUTLET FOR CLARITY N HANGER BRACKET Egua HANGER BALL DOWNROD ASSEMBLY e A WARNING To avoid possible fire or shock do not pinch wires between the hanger ball downrod assembly and hanger bracket Wiring The Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrictan A WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring NOTE If you are not sure if the outlet box is grounded contact a licensed electrician for advice as it must be grounded for safe operation Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply this may be a bare wire or wire with green colored insulation Securely connect wires using wire connectors supplied Figure 12 d WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result In person
12. talling the three mounting screws Figure 7 MOTOR CONNECTOR NES SWITCH HOUSING MOUNTING SCREW AN ta S LEI CD 2 ENE CONNECTORS BLACK WIRE WHITE WIRES SCREWS 7 A WARNING NUT Q meee Be FAN oH Do not pinch wires between the switch housing VOCKWASHER i CHAIN assembly and the switch housing plate ITCH LIGHT D SWITCH HOUSING FITTER AR EN ASSEMBLY BOWL MOUNTING i A ol CAP SCREWS 3 IND O gl Figure 5 7 gt DE en M Figure 7 15 Install two 60 watt maximum candelabra base light bulbs into the light fitter sockets Figure 8 16 Remove the finial nut and outer bowl cap from the light fitter Figure 8 17 Pass the fan switch chain through the cut slotted hole in the bowl cap Figure 8 A WARNING To avoid possible fire hazard do not exceed wattage Indicated on the fitter FAN SWITCH CHAIN 60 WATT GANDELABRA BASE BULBS 2 A S B VE TT TIGHT FITTER BOWL CAPET THREADED NIPPLE N gyags BOWL FESTE EEE OUTER PPEP GAP FINAL NUT LIGHT SWITCH HAIN PENDANTS 2 Figure 8 mn 18 Position the glass bowl over the threaded nipple and seat bowl on bowl cap Figure 16 Pass the fan pull chain through the bushing in the outer bowl cap and install the cap on the threaded nipple Install nut finial finger tight CAUTION Be sure that the fan switch chain does not make contact with the light bulbs If necessary reposition the light fitter to avoid the fan switc
13. ug screw from the switch housing assembly Figure 4 Remove and retain the two wire connectors 12 a SWITCH CUP CONNECTOR 113 SWITCH za GUP CENTER PLUG SCREW Figure 4 10 Remove and retain the lockwasher and nut from the light fitter Insert the black and white wires from the light fitter through the center hole in the switch housing assembly Thread the switch housing assembly onto the light fitter Reinstall the lockwasher and nut and tighten securely Figure 5 Connect ihe white wire from the ceiling fan to the white wire of the light fitter Connect the biue wire from the ceiling fan to the black wire of the light fitter Use wire connectors previously removed to make connections Figure 5 Er 114 SWITCH CUP CONNECTOR Figure 6 Engage the connector of the switch housing assembly with the motor connector Figure 6 The two connectors are keyed and color coded and must be mated correctly color to color before they can be engaged Make sure the connectors latch closes properly Carefully tuck all wires and splices into the switch housing SW HOUSING ASSEMBLY SWITCH HOUSING CONNECTOR Remove the three switch housing mounting screws Figure 7 from the switch housing plate Position the switch housing assembly on the switch housing plate and align the holes in the switch housing assembly with the holes in the plate Secure the switch housing assembly by ins
14. upporting at least 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot ceiling The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades Follow the recommended Instructions for the proper method of wiring your ceiling fan If you do not know enough about electrical wiring have your fan installed by a licensed electrician NOTE This fan is NOT suitable for use with solid state speed controls WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result In personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert forelgn objects in between rotating fan blades WARNING To reduce the risk of electrical shock this fan must be installed with an
Download Pdf Manuals
Related Search