none XXAQ-CR-WD Instructions / Assembly
Contents
1. installing on a steep sloped ceiling Fig 3 Figure 2 ANGLED CEILING MAXIMUM 24 ANGLE Provide strong To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar as shown in Fig 4 Ceiling hanger bracket Recesse outlet box Figure 3 Outlet box Figure 4 3 g2. READ AND SAVE THESE INSTRUCTIONS i eee FAN RATING AC 120V 60Hz TOOLS AND MATERIALS REQUIRED Philips screw driver Standard flat head screw driver 41 mm wrench Step ladder Wire cutters PACKAGE CONTENTS Unpack your fan and check the contents You should have the following items Hanger bracket assembly Ball down rod assembly Coupling cover Fan motor assembly Metal blades with cages decorative or safety 2 or Wood blades 2 Receiver with 6 wire nuts Transmitter holder 2 mounting screws Allen wrench Package Mounting hardware wood screws 2 screws 2 lock washers 2 washers 2 star washers 2 wire nuts 3 oaoo8 ase Th If blades are metal and accompanied by safety cages see Diagram e i To reduce the risk of injury to persons install fan so that blades are at least 7 0 Ft above the floor in the US and 8 3 Ft 2 5 M above the floor in Canada If blades are metal and accompanied by decorative cages See Diagram e ii or unguarded wooden blades See Diagram e iii To reduce the risk of injury to persons install fan so that blades are at least 10 0 Ft above the floor in the US and 10 0 Ft 3 05 M above the floor in Canada Wi AA LY READ AND SAVE THESE SAFETY AND INSTALLATION INSTRUCTIONS Consult a licensed electrician if unsure of any point below mentioned DANGER WARNING CAUTION High voltage and moving pers around motors and moto
3. lized 10 0 Ft if safety cages are not utilized In the US to satisfy UL requirements at least 7 0 Ft above the floor and all objects in room if safety cages are utilized 10 0 Ft if safety cages are not utilized To reduce the risk of personal injury do not bend blades or any other part of fan when cleaning Do not insert foreign objects in between rotating fan blades or in space surrounding entire rotating fan unit Fan must be turned off at power at supply source before installation cleaning or servicing 10 Instructions for Supply Connections Conductor of a fan identified as grounded conductor to be connected to a grounded conductor of a power supply conductor of fan identified as ungrounded conductor to be connected to an ungrounded conductor of a power supply conductor of fan identified for equipment grounding to be connected to an equipment grounding conductor After making the wire connections in junction box the splices should be turned upward and pushed carefully into the outlet box The wires should be spread apart with the grounded conductor and the fan grounding conductor on one side of the junction box and the ungrounded conductor on the other side of the outlet box Be sure that all wiring connections are properly insulated from each other and any surrounding metal parts For safety and best operating results we recommend that you have a qualified electrician assemble and install your fan 2 41 To reduce the ri
4. r driven equipment can cause serious or fatal injuries Always disconnect power source at main switch before wiring servicing or cleaning unit Do not rely on fan control device to prevent unexpected start up or electrical shock In addition power supply must have fuses or circuit breakers for short circuit protection All electrical wiring must conform to national and local electrical codes such as NEC OSHA etc 3 Fan should be secure in its electrical grounding to avoid possible electrical shock _ Fan should not be used in any wet or hazardous location defined by article 500 of the NEC In addition its ambient temperature should not exceed 104 degrees Fahrenheit Power supply should conform to voltage rating of 120V Before applying power visually re inspect the installation Make sure that all guards and protective devices are securely in place and all visible screws and bolts are tightened Warning to reduce the risk of fire electrical shock or personal injury mount hanging bracket to outlet box marked Acceptable for fan support and a hanging weight of 45 Lbs Do not mount fan to sheet rock or drywall type materials and use only the screws provided with the outlet box Caution to reduce the risk of injury to persons install fan so that bottom edges of fan blades are to be In Canada to satisfy CSA requirements at least 8 3 Ft 2 5 M above the floor and all objects in room if safety cages are uti
5. sk of personal injury install the supplementary mounting means and use only the hardware provided with the fan 42 Warning TO REDUCE THE RISKS OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING A Use this unit only in the manner intended by the manufacturer If you have any questions contact the manufacturer B Before installing servicing or cleaning unit switch power off at service panel and lock service panel to prevent power from being switched on accidentally 43 Warning To reduce the risk of fire electrical shock or personal injury mount to outlet box marked acceptable for fan support and use screws provided with outlet box ATTENTION Fan includes a 190W limiter to comply with the department of energy 2009 regulation Lamping this product over 190w will cause this fan to not light Please use bulbs with a total wattage under the 190W regulation ed vev RA rar JUNCTION BOX MOUNTING OPTIONS Secure the outlet box directly to the building structure Use appropriate fasteners and building materials The outlet box and its support must be able to fully support the moving weight of the fan at least 45 bs Use a UL Listed metal outlet box Do not use a plastic outlet box er bt Figures 1 2 and 3 are examples of different ways to mount the outlet box Note You may need a longer down rod to maintain proper blade clearance when 3 f Outlet box
Download Pdf Manuals
Related Search