Yosemite Home Decor ASHLEY-ORB Instructions / Assembly
Contents
1. wners Manua ASHLEY Net weight KGS s UL WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 2 3 M from floor when fan is in operation If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan Ifthe fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to tw2. her Fan assembly Wood Screw Pull Chain Knob Se Blade hold i ade holder Blade Balance Kit Spare switch cap Blade Screw Blade Pewee Paper Washer Motor screw Wire nuts Or Yoke cover l canopy set serew Outlet Box gt Install mounting bracket 2 3 to Outlet box in ceiling Turn off power at breaker Use metal outlet box suitable for USING washers and the box to avoid possible fan support mounting screws electrical shock Secure outlet box directly to the provided with the outlet building structure using wood box screws included Outlet box must support 40 Ibs Do not use existing ie mounting bracket replace it with new mounting bracket from box 5 This fan has two installation options and may be installed one of two ways 5a Downrod type ob Hugger type P2 5a 1 Yoke amp Downrod Assembly Wires Downrod Cotter Pin 7 Yoke cover Cross Pin Yoke oa Insert downrod through canopy and yoke cover then insert wires through downrod ob Insert the downrod assembly into yoke oc Insert the cross pin through Yoke and downrod and secure with cotter pin 5a 2 Hanging the fan Lift fan assembly onto mounting bracket Canopy S Downrod Set Screw od Tighten both set screws to further secure downrod 5e Pull down the yoke cover through downrod and put in place Mounting Bracket Ball Notch Carefully lift fan assembly onto mounting brac
3. ist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL listed and should be installed per the light kit s installation instructions After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury The fan can be made to work immediately after installation the bearings are adequately charged with grease So that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for indoor location use P1 1 Unpack and inspect fan carefully to be certain all contents are included Hardware bag Spring Washer Lock Was
4. ket Rotate fan so that the groove on the ball engages the ridge in the mounting bracket 5b 1 Yoke amp Canopy Assembly Take off canopy decorating cap from bottom of canopy then fasten 3 canopy set screws and washers provided from hardware bag onto yoke firmly 5b 2 Hanging the fan Lift the fan assembly and hang onto the tab on mounting bracket This will permit you to make the electrical connections without having to hold the fan up as well Wk A N oe RI z Washer setscrew 74 P AAN Coe Canopy LS lt 5 Canopy decorating cap Fan assembly Mounting bracket 5c Making wire connection for 110 120VAC 60Hz Follow diagram below and make sure that all exposed wires are secured inside wire nuts Note Wires from house may vary in color and may not include ground wire green After wiring is completed gently push wires into junction box with nuts pointing upward From House From Fan White lt a White AC N AC N Black GE M i om Black Blue for light kit Green M 1 cm Green for ground wire from downrod Green from mounting bracket Secure with twist lock wire nuts Included P3 5d Canopy installation 1 Take off left hand side screws one of each across on mounting bracket first then loosen the other two Left hand Push up the Canopy until the two screws on mounting side screw bracket are engaged with L
5. type slot holes on canopy 2 Screws on mounting bracket Rotate the canopy slightly until the two screw heads are in the L type slot holes 3 Tighten 4 screws firmly 6 Blades installation Attach blade to blade arm with screws amp washers provided in hardware bag Make sure that all screws are firmly tightened 7 Blade assembly to motor Attach the blade assembly to motor using motor screws from hardware bag NOTE Do not bend blade or blade arm to prevent wobble 8 Make wire connections for light kit Loosening 3 screws from the switch housing cover of light kit Switch Housing 1 White wire from Light Kit to white wire from fan White Wire Se Blue Wire and connect by wire nut Oy White Wire _ 2 Black wire from Light Kit to blue wire Switch Housing SS af A Screw from fan and connect by wire nut Over Light Kit C Fitter Attach light kit cover and light kit assembly to switch housing by 3 original screws 9 Light kit Installation i Light Kit Fitter bx Spring Pull Chain clip x 3pcs Knob Lamp Holder 1 2 3 Install bulbs 13W CFL bulbx 1 Install the glass into light kit Connect knob to pull chain included to lamp holders fixture by 3 spring clips on light fixture 10 Turn on the power your fan Is ready for operation P4
Download Pdf Manuals
Related Search