TroposAir Mounting Options have been updated. Instructions / Assembly
Contents
1. Outlet Box f Mounting Bracket 1B Installing Downrod and Yoke 2 Remove cross pin and cotter pin from downrod 2 Insert downrod through canopy and yoke cover and feed motor lead wires through downrod 3 Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke 4 Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod 6 Pull down the yoke cover to cover yoke Wires ___ f Screw 2 J Loosening 1C Hanging the fan Rotate fan so that the groove on the ball engages Lift fan assembly onto mounting bracket the ridge in the mounting bracket j Mounting Nis y Bracket Mounting Bracket Ball Groove 2 WIRE CONNECTION Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block Note Wires from house may vary in color and may not include ground wire green White wire from house to white wire from fan Black wire from house to black wire from fan Ground wire from house to green wires from downrod and from mounting bracket Secure with twist lock wire nuts provided from hardware bag Gently push wires into junction box with wire nuts pointing upward From House From Fan a s j i White ER 8 White MOTOR N Black gt A E B ac k MOTOR L Blue a2. Arr 7 Green amp from downred Green AC L from mounting bracket Note Two screws are pre installed on mounting bracket for canopy installation 2 Push up canopy until two screws pre screwed on mounting bracket are engaged with two key holes on canopy Rotate canopy slightly until two pre installed screw heads are engaged in the narrow end of key holes 3 Tighten both screws aie 4 BLADE INSTALLATION 4A Remove two pre screwed blade screws and keep for next step installed 7 Blade Screw 2 r striae installed 7 Removing ff Paper Spacers remove number pre serewed hs installed Fan Assembly 4B Attach blades to fan assembly by using blade screws removed from step 4A Repeat until all 3 blades are installed firmly Blade Screw remove number i Blade ly 5 PULL CHAIN KNOB INSTALLATION Connect Pull Chain Knob provided from hardware bag to the pull chain from switch housing L E E P5
3. from floor when fan is in operation 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets amp After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side T Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL ETL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be made to work immediately after in
4. Owners Manuci roposir Tornado This instruction contains 5 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation and Hanging system installation Page 4 Wire connection Canopy installation and Blade installation Page 5 Pull Chain Knob installation aa i PARTNER Net weight Intertek ENERGY STAR eee eee ELOU ETE KGS Toll Free 1 855 676 7247 LBS WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products require the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 10 feet
5. stallation The bearings are adequately charged with grease so that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 The fan is suitable for flat or sloped ceilings 12 This fan is reversible 13 This fan is light kit adaptable 14 This fan is remote adaptable 15 This fan is suitable for damp location use P1 Unpack and inspect fan carefully to be certain all contents are included Mounting Bracket Z a Hardware Bag For Mounting Plate Flat Washer no Spring Washer x3 _ ai Machine Screw Downrod i Wood Screw For Wire Connection Wire Nut x 3 4 A A For Fan and Light Pull Chain Knob x1 For Blade Balance Balanced slide x 4 SB Weight block 3G x 3 ODD Yoke Cover _ Blade 3 Fan Assembly Al Unit pack all in one box iia P2 WARNING blades should be at least 10 feet from floor Note 1 Note 2 Turn off power at breaker Use metal outlet box suitable box to avoid possible for fan support electrical shock Outlet box must support 35 lbs min f 1 HANGING SYSTEM INSTALLATION 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers from the hardware bag
Download Pdf Manuals
Related Search