none B552QI-BN Instructions / Assembly
Contents
1. Remove the fan from the hook on the mounting bracket A Secure the canopy C to the mounting bracket A with the four mounting bracket screws with lock washers BB Raise up the canopy ring B and line up the four tabs with the four grooves on the canopy C Once lined up slide the canopy ring B and secure it to the canopy C until snug HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Assembly Attaching the Fan Blades 8 Removing the rubber packing mounts The fan motor assembly F is shipped with rubber packing mounts PP to prevent movement during transportation Remove the five rubber packing mounts PP from the fan motor assembly and discard prior to attaching the blade arms 9 Attaching the blades to the blade arms NOTE Your fan blades are reversible Select the blade side finish which best accentuates your decor Using the screws already installed on the blade arms I attach the blade arm support plate G and blades H to the blade arms I Slide the screws on the blade arms I to the narrow portion of the key hole slot on the blade arm support plate G by pushing the tab QQ back until the rectangle plastic band RR falls into the hole on the blade this locks the blade assembly To remove the blade H from the blade arm pull the rectangle plastic band RR up and slide the screws toward the wi2. and that no bare wire is visible at the wire i WARNING Check to see that all connections are tight nuts except for the ground wire WARNING To reduce the risk of fire or electric shock do not use this fan with any solid state speed control device If you feel you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrician Follow the steps below to connect the fan to your household wiring Use the plastic wire nuts AA with your fan Secure the plastic wire nuts AA with electrical tape Make sure there are no loose strands or connections Connect the ground conductor CCC of the 120V supply this may be a bare wire or a wire with green colored insulation to the green ground lead s LL of the fan When using standard ceiling mounting there are two green grounding leads one from the mounting bracket A and one from the hanger ball downrod assembly E When using close to ceiling mounting there is only one green ground lead LL from the mounting bracket A since the hanger ball downrod assembly E is not used Connect the fan motor white wire MM to the supply white neutral wire BBB using a plastic wire nut AA Connect the fan motor black wire NN and the blue wire 00 to the supply black hot wire AAA using a plastic wire nut AA Turn the wire nut connections upward spreading them ap
3. FF Collar mounting screw with lock washer preassembled GG Blade arm screw with lock washer preassembled HH Pull chain and fob Rubber gasket HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Questions problems missing parts Before returning to the store call Home Depot Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM Retain this manual for future use B552Q100001 A
4. a plastic outlet box The illustrations below show three different ways to mount the outlet box JJ not included JJ N JJ To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar KK not included as shown above Assembly Standard Ceiling Mounting 1 Preparing the canopy 2 Preparing the motor Remove the canopy ring B from the canopy C Remove the clevis pin CC and cotter pin DD and loosen the two collar setscrews EE from the motor Remove the two non slotted screws BB from the F collar canopy C and loosen the slotted screws BB on the canopy C DD Remove the canopy C from the mounting bracket A by turning the canopy C counterclockwise 3 Assembling the fan Insert the cotter pin DD through the hole near the end of the clevis pin CC until it snaps into the locked position WARNING Failure to properly install the cotter pin DD could result in the fan becoming loose and possibly falling Tighten the two collar setscrews EE on top of the fan motor assembly F firmly NOTE If a longer downrod is needed not included take out the screw located in the hanger ball lower the hanger A ball and remove the pin Remove all three pieces from the downrod and assemble them onto the new longer downrod before proceedi
5. accorded by law Some states do not allow the exclusion of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer Contact the Customer Service Team at 1 877 527 0313 or visit www homedepot com Pre Installation SPECIFICATIONS Fan size Speed Volts Amps Watts RPM CFM N W G W C F 52 in na 120 ie kas DARKO BB3KG Giit Medium 0 37 30 134 3757 16 34 Ib 18 34 Ib High 0 51 61 1 194 5302 LISTED TOOLS REQUIRED DP Phillips Flat blade Step Wire Electrical AT screwdriver K screwdriver ladder stripper Tape Pre Installation continued HARDWARE INCLUDED A NOTE Hardware shown to actual size unless noted otherwise in the table below DD AA uo E BB P EE cc T GG Description Quantity AA Plastic wire nut BB Mounting bracket screw preassembled 4 CC Clevis pin preassembled 1 DD Cotter pin preassembled 1 EE Collar setscrew preassembled 2 FF Collar mounting screw with lock washer preassembled 6 GG Blade arm screw with lock washer preassembled 10 HH Pull chain and fob not
6. the fan GO mounting screws FF could result in the fan becoming loose WARNING Failure to completely tighten the three collar and possibly falling Make sure the slot openings of the canopy ring B B are on top and then proceed to place the rubber gasket lI canopy ring B and canopy C over the collar at the top of the fan motor assembly F Align the mounting holes in the bottom of the canopy C and the mounting holes in the rubber gasket Il with the holes in the top of the fan motor assembly F Fasten using the three collar mounting screws with lock washers FF previously removed Tighten the collar mounting screws FF securely 10 Assembly Hanging the Fan 4 Attaching the fan to the electrical box A WARNING To reduce the risk of fire electric shock or other personal injury mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box Pass the 120 volt supply wires through the center hole in the mounting bracket A Install the mounting bracket A to the outlet box JJ with the screws and washers provided with your outlet box When using close to ceiling mounting it is important that the mounting bracket A be level If necessary use leveling washers not included between the mounting bracket A and t
7. the two types of installation Standard Ceiling Mounting Close to Ceiling Mounting 7 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Installation MOUNTING OPTIONS WARNING To reduce the risk of fire electric shock or personal injury mount the fan to an outlet box marked acceptable for fan support using the screws provided with the AN outlet box An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced If in doubt consult a qualified NOTE You may need a longer downrod to maintain proper blade clearance when installing on a steep sloped ceiling A The maximum angle allowable is 18 away from horizontal If the canopy C touches the hanger ball downrod assembly E then remove the decorative canopy bottom cover D and turn the canopy C 180 before attaching the canopy C to the electrician mounting bracket A If your ceiling fan does not have an existing UL listed mounting box then install one using the following instructions KK Disconnect the power by removing the fuses or turning off the circuit breakers Secure the outlet box JJ not included directly to the building structure Use appropriate fasteners and materials not included The outlet box and its bracing must be able to fully support the weight of the moving fan at least 35 Ibs Do not use
8. Item 176 925 Model B552QI BN USE AND CARE GUIDE FARMINGTON 52 INCH CEILING FAN Questions problems missing parts Before returning to the store call Home Depot Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 va fa HOMEDEPOT COM THANK YOU We appreciate the trust and confidence you have placed in Home Depot through the purchase of this ceiling fan We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Home Depot Table of Contents Table of Contents ccccccceeeesesesesssesseseeeseeesesssssssesseensnens 2 Safety Information 2 cccecceeeeeeeeeseeeeeeeeeeeeeeeeeeeneeeseees 3 Warranty 0a AA 4 Pre Installatlon AGING 4 SSDOCITICAUOMINS NAAN 4 Tools Required amain 4 Hardware nod ud uaudauduau aai aaa 5 Package Contents Ka animamaniabuniaimasunbakiman 6 Dual Mounting Instruction u uuumakamanawwanasasasanaasasaasanaanassanana 7 Installation aaa GIAN AGA 8 Assembly 71171122200 RAN EG 9 Standard Ceiling Mounting u uuuuummmhaukunaunuwausuwausawsusawsuwausuwaana 9 Close to Ceiling MOUNTING uuumumkaaunuwnunuwausuwausawsunawsusansuwaana 10 Hanging the Fan a AA 11 Attaching the Fan Blades u uuumuumumammunawauwawauwawnuwawsuwausawausawaunan 14 Operation aNG NAAANINAG 16 Pull Chain Operating Instructions cccsessseeeeeeeeeeeeees 16 Reverse Swi
9. art so the green ground LL will be on one side of the outlet box JJ and the white MM black NN and blue wire 00 will be on the other side Carefully tuck the connections up into the outlet box JJ 12 Assembly Hanging the Fan continued F a Standard ceiling mounting 7b Close to ceiling mounting WARNING Make sure the tab on the mounting bracket A properly sits in the groove in the hanger ball E before attaching the canopy C to the mounting bracket A by turning the canopy housing until it drops into place WARNING The locking slots of the canopy C are provided only as an aid to mounting Do not leave the fan assembly unattended until all four canopy screws are engaged and firmly tightened AN WARNING The locking slots of the canopy C are provided only as an aid to mounting Do not leave the fan assembly unattended until all four canopy screws are engaged and firmly tightened Slide the canopy C up to the ceiling Make sure you have placed the wires safely into the outlet box JJ Secure the canopy C to the mounting bracket A with the four mounting bracket screws and lock washers BB included with your fan Raise up the canopy ring B and line up the four tabs with the four grooves on the canopy C Once lined up slide the canopy ring B and secure it to the canopy C until snug
10. de portion of the key hole slot on the blade support plate G This will loosen the blade H and blade arm support plate G and will allow you to remove the blade H from the blade arm I 14 Assembly Attaching the Fan Blades 1 Fastening the blade assemblies to the motor WARNING To reduce the risk of personal injury do not bend the blade arms I while installing balancing the blades H or cleaning the fan Do no insert foreign objects between rotating fan blades H Fasten the blade assemblies H to the fan motor assembly F by lining up the slots of the blade arms SS with the tabs on the motor TT Tighten the two screws and lock washers GG already installed in the blade arms I Repeat this procedure with the remaining blade arms 1 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Operation PULL CHAIN OPERATING INSTRUCTIONS Install pull chain and fob HH onto the pull chain located in the switch housing Turn on the power and check the operation of the fan The pull chain controls the fan speed as follows 1 pull High 2 pulls Medium 3 pulls Low and 4 pulls Off Speed settings for warm or cool weather depend on factors such as the room size ceiling height and number of fans REVERSE SWITCH OPERATING INSTRUCTIONS The reverse switch is located on the surface of the switch housing This switc
11. e outlet box and the ungrounded conductor on the other side of the outlet box 9 All setscrews must be checked and retightened where necessary before installation not use this fan with any solid state fan speed control device h WARNING To reduce the risk of electrical shock or fire do It will permanently damage the electronic circuitry WARNING To reduce the risk of personal injury do not bend the blade arms also referred to as flanges when installing the brackets balancing the blades or cleaning the fan WARNING Do not insert foreign objects between rotating fan blades WARNING To reduce the risk of fire electric shock or personal injury mount the fan to the outlet box marked acceptable for fan support with the screws provided with the outlet box CAUTION To reduce the risk of personal injury use only the screws provided with the outlet box HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Warranty We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser We also warrant that all other fan parts excluding any glass or acrylic blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser We ag
12. h controls directions forward switch down or reverse switch up NOTE Wait for the fan to stop before reversing the direction of the blade rotation Warm weather Counterclockwise Direction A downward air flow creates a cooling effect This allows you to set your air conditioner on a warmer setting without affecting your comfort Cool weather Clockwise Direction An upward air flow moves warm air off the ceiling This allows you to set your heating unit on a cooler setting without affecting your comfort 16 Care and Cleaning Do Do not Check the support connections brackets and blade Use water when cleaning Water could damage the motor attachments twice a year Make sure they are secure or the wood or possibly cause an electrical shock Because of the fan s natural movement some connections may become loose over time It is not Apply oil to your fan or motor The motor has necessary to remove the fan from the ceiling permanently lubricated sealed ball bearings Clean your fan periodically Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or tarnishing Optional Apply a light coat of furniture polish to the wood blades Optional Cover small scratches with a light application of shoe polish Troub
13. he outlet box JJ Note that the flat side of the mounting bracket A is toward the outlet box JJ Securely tighten the two mounting screws Hanging instructions for standard mounting WARNING The tab in the ring must rest in the groove of the hanger ball E Failure to properly seat the tab in the groove could cause damage to the wiring Carefully lift the fan motor assembly F up to the mounting bracket A and seat the hanger ball E in the mounting bracket A socket Make sure the tab on the mounting bracket A socket is properly seated in the groove in the hanger ball E This will help to balance the ceiling fan 5 Hanging instructions for close to ceiling mounting A WARNING The hook is only to hold the fan while attaching wiring Failure to hang as instructed may result in the tab breaking causing the fan to fall The hook must pass from the inside to the outside of the canopy Carefully lift the fan motor assembly F up to the mounting bracket A and hang the fan on the hook provided using one of the holes at the outer rim of the canopy C HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Assembly Hanging the Fan continued Making the electrical connections AAA BBB CCC WARNING To avoid possible electrical shock be sure electricity is tumed off at the main fuse box before wiring including ground
14. leshooting panel box before you attempt any repairs Refer to the section WARNING Make sure the power is off at the electrical Making the Electrical Connections on page 12 Problem Solution Check the main and branch circuit fuses or breakers The fan will not start Check the line wire connections to the fan and switch wire connections in the switch housing Make sure all motor housing screws are snug Make sure the screws that attach the fan blade arm to the motor hub are tight Make sure wire nut connections are not rattling against each other or the interior wall of the switch housing Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this The fan sounds noisy time If using the ceiling light kit make sure the screws securing the glassware are tight Check that the light bulb is also secure Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling Make sure your Ceiling box is secure and rubber isolator pads are used between the mounting bracket and outlet box 17 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Troubleshooting continued Problem Solution The fan wobbles Verify that all blades and blade bracket screws are secure most fan wobble p
15. ng step 3 Route the wires exiting from the top of the fan motor assembly F through the canopy ring B Ensure the slot openings are on top Route the wires through the canopy C and then through the hanger ball downrod assembly E Align the holes at the bottom of the hanger ball downrod assembly E with the holes in the collar on top of the fan motor assembly F F Carefully insert the clevis pin CC through the holes in the collar and the hanger ball downrod assembly E Be careful not to jam the clevis pin CC against the wiring inside the hanger ball downrod assembly E 9 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Assembly Close to Ceiling Mounting 1 Preparing the canopy 2 Preparing the motor Remove the canopy ring B from the canopy C Remove three of the six collar mounting screws with lock washers FF every other one from the collar on top of the fan motor assembly F Remove the mounting bracket A from the canopy C by loosening the four canopy mounting bracket screws BB on the top of the canopy C Remove the two non slotted canopy mounting bracket screws BB and loosen the slotted canopy mounting bracket screws BB Remove the canopy bottom cover D from the canopy C by turning the canopy bottom cover D counter clockwise Assembling
16. ree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident misuse improper installa tion or by affixing any accessories is not covered by this warranty Because of varying climatic conditions this warranty does not cover any changes in brass finish including rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered a defect Servicing performed by unauthorized persons shall render the warranty invalid There is no other express warranty We hereby disclaim any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except as may otherwise be
17. roblems are caused by loose parts Once the fan is properly installed run the ceiling fan for 10 minutes to let the fan self adjust If wobble occurs after running the fan for 10 minutes verify blade level using the following process Select a point on the ceiling above the tip of one of the blades then select any fan blade and measure from the center of the selected blade to the point on the ceiling Rotate the fan until the next blade is positioned and repeat the measurement using the same point from the ceiling for every blade Measurement deviations should be within 1 8 in If all deviations are less than 1 8 in and the fan continues to wobble please call Customer Service 1 877 527 0313 to order a complimentary Blade Balancing Kit If deviation is greater than 1 8 in please call Customer Service 1 877 527 0313 to order complimentary replacements of your brackets 18 Service Parts T 5 T BB T GG pun Part Description Mounting bracket preassembled Canopy ring Canopy Canopy bottom cover Hanger ball downrod assembly Fan motor assembly Blade arm support plate Blade I olnm ojoj Blade arm 19 CD EB EE Part Description AA Plastic wire nut BB Mounting bracket screw preassembled CC Clevis pin preassembled DD Cotter pin preassembled EE Collar setscrew preassembled
18. tch Operating Instructions csceeeeeeees 16 Care and Cleaning cccccccssesseeeeeeeeeeeeeeeeeeeneenseneees 17 Troubleshooting maa aamin 17 Service Parts XX seen sedscnstwanecwacdauuvoxsunatandsuctecwanctes 19 Safety Information 1 To reduce the risk of electric shock ensure electricity has been turned off at the circuit breaker or fuse box before beginning 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 1999 and local electrical codes Electrical installation should be performed by a qualified licensed electrician 3 The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs Use only UL listed outlet boxes marked FOR FAN SUPPORT 4 The fan must be mounted with a minimum of 7 ft clearance from the trailing edge of the blades to the floor 5 Avoid placing objects in the path of the blades 6 To avoid personal injury or damage to the fan and other items be cautious when working around or cleaning the fan 7 Do not use water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning 8 After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of th
19. to scale 1 ll Rubber gasket not to scale 1 5 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Pre Installation continued PACKAGE CONTENTS A B E F Part Description Quantity Part Description Quantity A Mounting bracket preassembled 1 F Fan motor assembly 1 B Canopy ring preassembled 1 G Blade arm support plate 5 C Canopy 1 H Blade 5 D Canopy bottom cover 1 l Blade arm 5 E Hanger ball downrod assembly 1 Pre Installation continued DUAL MOUNTING INSTRUCTIONS This ceiling fan is supplied with two types of hanging assemblies the standard ceiling installation using the downrod with ball and socket mounting and the close to ceiling mounting The close to ceiling mounting is recommended in rooms with less than 8 ft ceilings or in areas where additional space is desired from the floor to the fan blades When using the standard downrod installation the distance from the ceiling to the bottom of the fan blades will be approximately 12 in The close to ceiling installation reduces the distance from the ceiling to the bottom of the fan blades to approximately 9 in Once you have decided which ceiling installation you will use refer to the corresponding sections and procedures during the assembly period Where necessary each section of the instructions will note the different procedures to follow for
Download Pdf Manuals
Related Search