TroposAir 88101 Instructions / Assembly
Contents
1. Mounting Plate Safety cable amp Wires Hanging Base with receiver and oscillating motor Hardware Bag Canopy For Mounting Plate Flat Washer x3 Spring Washer x3 Machine Screwx2 Wood Screw x3 Downrod Yoke For Hanging Base Motor Yoke Set Screw x 2 For Canopy Set Screw x 5 one spare screw included Gb UG 8 For Wire Connection Blade x3 Wire Nut x 3 a l a For Blade Installation Blade Screw x7 one spare screw included FFF FF Paper Washer x 7 one spare washer included Remote Battery Included Bs Hardware Bag Wood Screw x2 S S P2 NOTES BEFORE INSTALLATION Note 1 This is an oscillating ceiling fan with features of 110 degree oscillation controlled by remote and 3 vertical positions 0 45 90 degree manual tilt 110 degree oscillation 3 adjustable motor positions from center line 55 degree left 55 degree right 0 45 90 degree CARRE IN RSD LII N Center Line Note 2 To gain maximum sweep space it is recommended to locate this fan close to a wall or corner This will save ceiling space and not influence existing lights f zA S Maximum sweep area 286 3 square feet 26 6 square meter WARNING To avoid fan blades hitting walls during oscillation a minimum distance of 16 1 inches 410mm is required from downrod center of mounting plate to both sides of the wall at corner Center of Mounting Plate WARNING Fan2. with any object Fan must be installed at least 7 feet from floor to prevent injury when fan is in operation If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan Ifthe fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets After making electrical connections spliced conductors should be turned upward The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side and the HOT wires on the other side After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury This fan is not suitable for slope ceiling This fan is not reversible 10 This fan is not light kit adaptable 11 This fan is suitable for damp location use P1 Unpack and inspect fan carefully to be certain all contents are included
3. Owner s Manual roposir Mustang 3MT18 1M This instruction contains 7 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation Page 4 Hanging system installation Page 5 Wire connection Page 6 Hanging base and Canopy installation Page 7 Set up motor position Blade installation and Remote Net weight Toll Free 1 855 676 7247 WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 2 tl 3 l 4 9 R 6 i f 8 9 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning To avoid possible electric shock be sure electricity is TURNED OFF atthe main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections Make sure that your installation site will not allow rotating fan blades to come in contact
4. agonal holes on mounting plate where 2 Ltype slots on hanging base are to engage After minor adjustment direction marks on mounting plate and hanging base may not be aligned Mounting Plate Hanging Base ew air direction New air direction fig 1 fig 2 3B Push up canopy and secure to hanging base with 4 set screws from hardware bag 4 SET UP MOTOR POSITION NOTE Fan motor is at 0 degree when taken out from the carton no need to change motor angle if intend to use the fan at 0 degree There is one indicating line on downrod yoke and three on motor yoke for aligning 0 45 90 degree motor position see fig 1 4A Remove set screw and spring washer from motor yoke see fig 2 4B Adjust motor angle by aligning one out of three indicating lines 0 45 90 on motor yoke with indicating line on downrod yoke see fig 2 4C Secure set screw and spring washer removed from step 4A back to motor yoke Make sure set screw is firmly tightened see fig 2 fig 1 For 0 degree a For 45 degree a For 90 degree Downrod Yoke Downrod Yoke Downrod Yoke Downrod Yoke Motor Yoke Indicating Line 1 D Indicating Line 3 Set Screw Motor Yoke 5A 5B 5C Attach blade to blade holder Attach blade assembly to flywheel Thread the cap counter clockwise with screws amp washers provided aligning beveled center hole on to motor shaft until fully tightened in hardware bag Make sure that flywheel with beveled mo
5. r from hardware bag Pass wood screw through closed loop of safety cable Secure wood screw to ceiling joist through any available slot on mounting plate Make sure safety cable has been tightened securely CAUTION THE WOOD SCREW AND ITS SUPPORT MUST BE ABLE TO FULLY SUPPORT THE WEIGHT OF AT LEAST 100 LBS 3N AH ZA m MN KE We i l RX uf SS Yate ue WS i Flat Washer Spring Washer Wood Screw Mounting Plate lt Safety cable Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts Note Wires from house may vary in color and may not include ground wire green After wiring is completed collect wires neatly inside hanging base White wire from house to white wire from receiver Black wire from house to black wire from receiver Ground wire from house to green wire from hanging base and from mounting plate Secure with twist lock wire nuts Included Outlet Box From House White gt 4 s J M Neui l Neutral From Hanging Base Green x Green Fee gt ee ee From Mounting Plate l Green N L 2C Setting code switches for transmitter and receiver Remote controls are tuned to operate together using 4 switches for 16 possible code combinations 1 Setting the code on the TRANSMITTER 2 Setting the code on the RECEIVER Slide code switches on the Receiver to be Remove bat
6. should be at least 7 feet from the floor Note 1 Turn off power at breaker box to avoid possible electrical shock Note 2 Note 3 Use metal outlet box suitable CAUTION for fan support Oscillating device located Outlet box must support 35 Ibs min at hanging base is fragile do not damage or bend oscillating parts cam arm motor during installation Hanging Base 1 HANGING SYSTEM INSTALLATION Installing mounting plate to ceiling outlet box IMPORTANT Align Mounting Plate to desired oscillator direction now 1A Pull house wires from outlet box through the center hole of mounting plate Outlet Box 1D Hanging the fan 1B 1C The screw hole between direction Attach mounting plate to outlet box marks is for finding out intended air by securing with screws included direction Adjust mounting plate by with the outlet box and washers aligning 2 slots of mounting plate from the hardware bag through 2 with screw holes on outlet box see outof6slots on mounting plate fig 1 Outlet Box Outlet Box n m ate R Mounting Plate intended Air Ditection Wea sied Oscillating Directions fig 1 Lift the fan assembly and hang onto the J hook through oval shaped hole on mounting plate This will permit you to make the electrical connections without having to hold the fan up as well N 2 WIRE CONNECTION 2A Attaching safety cable to ceiling joist Use wood screw spring washer and flat washe
7. tery cover 2 Slide code switches to your choice of ON or OFF position the SAME POSITIONS as set on your Transmitter Use a small screwdriver or ball point pen to slide each switch firmly up or down 3 Install 9V DC battery Included 4 Install battery cover on transmitter Receiver Transmitter Code Switches Code Switches 3 HANGING BASE AND CANOPY INSTALLATION 3A Carefully lift the fan assembly away from the hook on mounting plate Align direction marks on mounting plate with direction marks on hanging base see fig 1 2 Push up hanging base until 2 set screws pre installed on mounting plate are engaged with L type slots on hanging base see fig 1 G Slightly rotate hanging base until two screw heads are in L type slots see fig 2 4 Attach other 2 set screws from hardware bag to secure hanging base and mounting plate these will be the remaining 2 out of 4 set screws for securing hanging base to mounting plate see fig 2 Note Make sure all 4 set screws are firmly secured Direction Marks Screws on Mounting Plate Mounting Plate After above steps please check if air direction is the same as intended direction If not please take below steps for minor adjustment 1 Remove all 4 set screws from hanging base 2 Use direction marks on hanging base as center Rotate hanging base 45 degree to the left or 45 degree to the right for minor adjustment see fig 1 amp fig 2 3 Attach 2 set screws to two di
8. tor shaft This is reverse threaded all screws are firmly tightened before attachment i LOW Fan low speed OFF For fan speed and oscillation MED Fan middle speed l p OSC Button for ON OFF oscillation Hl Fan high speed Qo this button only functions when fan is in operation 7 Turn on the power your fan is ready for operation P7
Download Pdf Manuals
Related Search