AireRyder FN48121BN Instructions / Assembly
Contents
1. balancing the blades or cleaning fan Do not insert foreign objects in between rotating fan blades Before changing the fan direction turn off the fan and wait for the fan blades to stop completely f a stationary appliance is not provided with a supply cord and a plug or with other means for disconnection from the mains supply having a contact separation of at least 3 mm in all poles that means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules NOTE The safeguards provided by these safety instructions and by the separate installation instructions are not meant to cover all possible conditions and situations that may occur It must be understood that common sense caution and care are factors which can not be built into this product These factors must be supplied by the person s installing caring for and operating the fan WARNING TO AVOID RISK OF ELECTRIC SHOCK BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE TURNING OFF THE ELECTRICAL POWER BY USING THE LIGHT SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK TO REDUCE THE RISK OF INJURY INSTALL THE FAN SO THAT THE BLADES ARE AT LEAST 7 FEET 2 1 METERS ABOVE THE FLOOR AND AT LEAST 18 INCHES 0 5 METERS FROM THE TIP OF THE BLADES TO THE WALL TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY MOUNT TO OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND2. USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE ANSI NFPA 70 1999 AND LOCAL CODES IF YOU ARE UNFAMILIAR WITH THE METHODS OF INSTALLING ELECTRICAL WIRING SEEK THE SERVICES OF A QUALIFIED LICENSED ELECTRICIAN aireRyder F_ A N 090406 INSTALLATION INSTRUCTIONS IMPORTANT BEFORE YOU BEGIN INSTALLING THE FAN CAREFULLY READ ALL INFORMATION ON THE SEPARATE SHEET SAFETY INSTRUCTIONS AS WELL AS THE FOLLOWING INSTALLATION INSTRUCTIONS IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN THIS FAN MUST BE INSTALLED WITH A WALL CONTROL SWITCH SAVE ALL INSTRUCTIONS NOTE The fan weight is 16 7 Ib 7 5 kg Be sure the outlet box you are using is securely attached to the building structure and can support the full weight of the fan Failure to do so can result in serious injury Installation Steps Wood Member Ceiling Joist 2 x 4 Approx SOY HL THONS Var 7 L oa ae ae Z Ceiling Junction Box Hanger Bracket Turn OFF the electric power at the main fuse or circuit breaker box Tighten the hanger bracket to the outlet box with two mounting screws Make sure the outlet box is securely installed so that it will be able to support at least the fan weight WARNING MOUNT ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT Motor Wir Hanger Pin Remove the Lock Pin and take off Slide canopy and do
3. bracket Attach the loop at the end of the safety cable to the ceiling surface with screws then secure it with a flat washer and dry wall screw Make sure the flat washer and dry wall screw are covered by the fan canopy T 91 1 ot io 1 ot 1 1 a Screw Thread the blade screws through the Secure blade holders to the motor holes in the blade holder and the holes with motor screws and washers in the blade and into the decorative plates Tighten all screws securely Repeat with other blade PO eee E ACE POUAS OOG Make sure the wires of the fan light in blades properly according to the marks respectively labeled on the blade holders meow a aie pa ppea win ee and blades nuts Secure the switch box cover with the switch box screws Note To install the fan light skip this Fan Light Installation step and proceed to Fig 14 Switch Box Screw Switch Box Cover Assembly without fan light WARNING As per EPACT 2005 requirements this fan light has a built in current limiting device to conserve energy The fan light will not operate if the combined wattage of the installed bulbs exceeds 190 Watts If the fan light shuts off shortly after being switched on it may be due to excessive current demand Turn off power to the fan and replace the light bulbs with lower wattage bulbs Turn on power to the fan using the pull chain wall switch or remote control whichever is installed on the
4. ackage Contents Unpack your fan and check the contents You should have the following items 1 Hanger Bracket 2 Canopy 3 Downrod Set Includes Hanger Ball 6 in Downrod Hanger Pin amp Lock Pin 4 Downrod Stand Cover 5 Blade Holder X3 6 Decorative Plate X3 7 Housing 8 Switch Box Cover 9 Fan Light Set Includes GU10 Base MR16 Max 50W Bulbs 10 Fan Blade X3 11 Assembly Kit 12 Installation Instructions Dimension Reference Installed with 6 in Downrod A 21 1 2 in B 10 1 2 in C 2in D 7 1 2 in E 5 7 8 in aireRyder F A N 090406 Exploded View Detail LAI Hanger Bracket Canopy Hanger Ball 7 Downrod Downrod Stand Cover Hanger jn En Blade Holder Collar Housing Switch Box Fan Light Light Bulb Dual Mount Drawing Downrod Mount Slope Ceiling Mount Up to 23 degrees aireRyder F A N 090406 Safety Instructions READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS All set screws of the fan must be checked and retightened where necessary before installation To reduce the risk of personal injury do not bend the blade brackets when installing the brackets
5. aireRyder LIMITED LIFETIME WARRANTY Model No FN48121BN aireRyder ORIGINAL CEILING FAN LIMITED LIFETIME WARRANTY The limited lifetime warranty covers this ceiling fan for residential use by the original purchaser against defects in material or workmanship as follows lf your aireRyder Ceiling Fan motor fails at any time during the lifetime of the original purchaser due to defects in material or workmanship we will provide a replacement part free of charge If your Fan motor fails at any time within one year after the original date of sale to the original purchaser due to defects in material or workmanship we will provide labor to repair the defect with the exception of take down reinstallation free of charge The original purchaser will be responsible for all labor costs after this one year period If no replacement parts are provided for any part of your Fan motor that fails at any time during your lifetime due to defects in material or workmanship we will refund the original purchase price of your Fan lf your Fan blades pull chain switch reverse switch or any accessory except glass globes and light bulbs fails at any time within one year after the original date of purchase due to a defect in material and workmanship we will repair or if we choose replace the defective blades switch or accessory free of charge with the exception of take down reinstallation services If the original purchaser ceases to own the Fan this wa
6. glass remove glass and install a 1 4 in wide rubber band on glass neck to act as an insulator Replace glass and tighten screws against rubber band Some fan motors are sensitive to signals from Solid State variable speed controls DO NOT USE a Solid State variable speed control Allow break in period of 24 hours Most noises associated with a new fan will disappear after this period 3 If fan wobbles All blades are weighed and grouped by weight Natural woods vary in density which could cause the fan to wobble even though all blades are weight matched The following procedures should eliminate most of the wobble Check for wobble after each step 1 4 4 If light does not work Check that all blades are screwed firmly into blade holders 2 3 Check that all blade holders are tightened securely to motor Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box is mounted firmly to ceiling joist Most fan wobble problems are caused when blades are not equally level To check the blade levels select a point on the ceiling above the tip of any blade Measure the distance from the ceiling to the blade tip to an accuracy of 1 8 inch Rotate the blades until the next blade is in the measuring position Repeat measurement for each blade If all blade levels are not equal you can adjust blade levels by the following procedure To adjust a blade tip down insert a washer not sup
7. particular fan aireRyde F_ A N Cc O PAGE 2 4 090406 Connector Fan Light Bulb MR16 Max 50W included Switch Box Screw Metal Ring Make wire connections using the Secure the fan light onto the switch box Gently loosen the metal ring from connectors respectivly from the switch box and fan light The blue wire from the switch box to the black wire from fan light The white wire from the switch box to the white wire from fan light Carefully put the wires into the switch box Fig 17 Reverse Forward fi Y NY Fan Speed Pull Chain Fan Light Switch Pull Chain Turn ON the electric power at the main fuse or circuit breaker box using the switch box screws the glass shade then install bulbs included See relamping label at socket area or packaging for maximum allowed wattage Restore the metal ring back to the glass shade The slide switch sets the direction of fan rotation Select the direction of fan rotation you need by sliding the switch Push the slide switch bottom for Forward and top for Reverse CAUTION If you install a Remote Control or a Wall Control for this fan make sure to use the pull chains to select the high position for the fan speed and the on position for the fan light aireRyde F A N Cc O PAGE 3 4 090406 Tro
8. plied between the blade and blade holder at the screw closest to the motor To adjust a blade tip up insert washer not supplied between the blade and blade holder at the two screws farthest from the motor If blade wobble is still noticeable interchanging two adjacent side by side blades can redistribute the weight and possibly result in smoother operation Check blue wire from fan to make sure it is connected to hot wire from house Check for loose or disconnected wires in fan switch housing Check for loose or disconnected wires in light kit Check for faulty light bulbs CAUTION Make sure main power is turned off before entering switch housing If the fan light shuts off shortly after being switched on it may be due to excessive current demand Turn off power to the fan and replace the light bulbs with lower wattage bulbs Turn on power to the fan using the pull chain wall switch or remote control whichever is installed on the particular fan aire aireRyder er F A N PAGE 4 4 090406
9. rranty and any implied warranty including but not limited to any implied warranty of merchantability or fitness for a particular purpose become void This warranty and any implied warranty including but not limited to any implied warranty of merchantability or fitness for a particular purpose do not cover glass globes light bulbs or finish on any metal portions of the Fan This warranty is in lieu of express warranties The duration of any implied warranty of merchantability or fitness for a particular purpose with respect to any aireRyder Ceiling Fan motor blades switch or accessories is expressly limited to the period of the express warranty set forth above for such motor blades switch or accessories This warranty excludes defects malfunctions or failures of any aireRyder Ceiling Fan that are caused by repairs by persons not authorized by us use of parts or accessories not authorized by us mishandling improper installation modifications or damage to the Fan while in your possession or unreasonable use including failure to provide necessary maintenance In no event shall aireRyder Fan be liable for consequential or incidental damages Some states do not allow the exclusion or limitation of consequential or incidental damages in which case the above limitation or exclusion may not apply This warranty gives you specific legal rights and you may also have other rights which vary from state to state aireRyder F A N P
10. uble Shooting Guide If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly installation or wiring In some cases these installation errors may be mistaken for defects If you experience any faults please check this Trouble Shooting Guide If a problem cannot be remedied or you are experiencing difficulty in installation please call our Customer Service Department PROBLEM SUGGESTED REMEDY 1 If fan does not start T Check line wire connections to fan and switch wire connections in switch 2 If fan sounds noisy 1 Make sure the screws which attach the fan bladeholder to the motor are tight Make sure wire nut connectors in switch housing are not rattling against each oF 6 Check main and branch circuit fuses or circuit breakers housing CAUTION Make sure main power is turned off Make sure forward reverse switch is firmly in bottom or top position Fan will not operate when switch is in the middle Make sure that the wall control is turned ON Make sure all screws in motor housing are snug not over tightened other or against the interior wall of the switch housing CAUTION Make sure main power is turned off before entering switch housing If using an optional ceiling fan light kit check to be sure the screws securing the glassware are finger tight Check to be sure light bulb is tight in socket and not touching glass shade s If vibration persists from
11. wnrod stand Insert the Downrod into the Collar the Hanger Pin cover onto downrod as shown Slide Hanger Pin through holes of Then thread motor wires through Collar and Downed downrod Hanger Bracket Hang fan on hanger bracket and rotate the downrod until the chip on the hanger bracket snaps into the slot on the hanger ball Note For slope ceiling installation make sure the slot of hanger ball and the chip of hanger bracket are toward the floor Insert and tighten the two Collar Screws Slide Lock Pin into Hanger Pin until it locks into position aireRyde F AN 7 C O Make wire connections 1 The white motor wire to the white wire from the outlet box with a wire nut 2 The black motor wire and blue wire to the black wire from the outlet box with a wire nut 3 The ground wire from the outlet box to the ground wire from the motor with a wire nut After making the wire connections the wires should be spread apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box After the connections have been made the wires should be turned upward and pushed carefully up into the outlet box Green Ground Wood Member rT Ny SSS n Ai CCR KES i7 H J au IM SILIZLIIZ ZZA V2 NAY DAA 1 N Flat Washer NS 7 Junction Box Dry Wall ee Hanger Bracket Safety Cable Secure the canopy to hanger
Download Pdf Manuals
Related Search