none XXDI-TB-WD Installation Guide
Contents
1. MOUNTING INSTALLATION OF THE FAN Before touching a screw driver thoroughly read these instructions Warning Caution Before installing fan turn off power at service panel and check all visible screws and bolts for tightness 1 Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise Fig 5 2 Remove the hanger bracket from the canopy by removing the 1 of 2 screws from the bottom of the hanger bracket and loosening the other one a half turn from the screw head Next turn the canopy counter clockwise to removing the hanger bracket from the canopy Fig 5 3 Secure the hanger bracket to the ceiling outlet box using screws and washers included with your outlet box Fig 6 4 Remove hanger ball from down rod assembly by loosening set screws removing the cross pin and sliding ball off rod Fig 7 5A Metal Blade Head and Decorative Cage if your fan is one with a metal blade head and decorative cage remove protective plastic sleeve from the motor shaft and then attach the metal blade head and cage The Atlas medallion should be oriented correctly Handie a blade head carefully otherwise you will pend the blade irons and cause your fan to vibrate when in use Caution The set screw in the blade head hub must be counter sunk into the bore hole on the flattened side of the motor shaft or else the blade head may disengage from the motor shaft during operation 5B Meta Blade2. Head and Safety Cage If your fan is one with a metal blade head and safety cage remove protective plastic sleeve from the motor shaft then and attach the back side of the safety cage Next attach the blade head Handle your blade head carefully otherwise you will bend the blade irons and cause your fan to vibrate when in use Finally attach the front side of the cage with Atlas medallion oriented correctly Caution The set screw in the blade hub must be counter sunk into the bore hole on the flattened side of the motor shaft or else the blade head may disengage from the motor shaft during operation hanger bracket lt Ceiling CSS canopy cover Figure 5 Electrical gt ren box Ceiling Pl hanger bracket l l A a supplied w 120V Wires electrical box Figure 6 Cross pln gt Hanger bail q Allen wrench Figure 8 5 C Wooden Blade Head If your fan is one with wooden blade head attach your blades as the last step in the assembly process Do not attach them now Attach them in step No 9 Handle your blade head carefully otherwise you will bend the blade irons and cause your fan to vibrate when in use 6 Loosen the two set screws from the top coupling of the motor assembly Fig 8 7 Carefully feed the fan wires up through the down rod Thread the down rod into the coupling then tighten the set screws using the Allen wrench Fig 8 Carefully reinstall hanger ball ont
3. eds as follows L Low Speed M Medium Speed H High Speed B OFF Button This button turns the fan off C ACCESSORY Button This button is used to control the oscillating operation a 23AE 12V i Figure 14 Figure 15
4. in the same room Any code combination will operate the ceiling fan and light as long as the Receiver and Transmitter units are set to the same codes Fig 10 1 Insert Receiver into Hanger Bracket with the flat side of the Receiver facing the ceiling Fig 11 Regi slot Receiver stration Figure 11 2 Motor to Receiver Electrical Connections TL A Connect the WHITE wire from the fan to the a a core WHITE wire marked TO MOTOR N from the BLACK HOT WHITE NEUTRAL Receiver B Connect the BLACK wire from the fan to the WHITE AC IN N BLACK wire marked TO MOTOR L from the recever r Receiver BLACK TO MOTOR L ot NY C Connect the BLUE wire from the fan to the BLUE wire marked oscillation from the Receiver BLUE OSCILLATION Proceed to secure all wire connections with the plastic wire nuts provided Fig 12 GROUND 3 GROUND WIRES GREEN ON CEILING FAN BLUE OSCILLATION Note Fan must be instalied from a maximum E eas WHITE NEUTRAL distance of 40 feet from the transmitting unit for proper signal transmission between the transmitting unit and the fan s receiving unit 3 Receiver to House Supply Wires Electrical Connections A Connect the WHITE wire Neutral from the outlet box to the WHITE wire marked AC in N from the receiver B Connect the BLACK wire Hot from the outlet box to the BLACK wire marked AC in L from the receiver Secure al
5. l wire connections with the plastic wire nuts provided Fig 12 4 lf your outlet box has a GROUND wire Green or Bare Copper connect this wire to the Hanger Ball and Hanger Bracket Ground wires If your outlet box does not have a Ground Wire then connect Figure 12 the Hanger Ball and Hanger Bracket Ground Wires together Secure wire connection with the plastic wire nut provided Fig 12 l ooo Outlet box 5 Tuck connections neatly into ceiling outlet box 6 Slide the canopy up to hanger bracket and place aio the key hole on the canopy over the screw on the hanger bracket turn canopy until it locks in place at t t Sorews the narrow section of the key holes Fig 13 7 Align the circular hole on canopy with the i remaining hole on the hanger bracket secure by tightening the two set screws Note Adjust the canopy screws as necessary until the canopy and canopy cover are snug 4 Canopy Warning Make sure tab at bottom of hanger CED PAneRy Tover bracket is properly seated in groove of hanger ball before attaching canopy to bracket Failure to Figure 13 properly seat tab in groove could cause damage to electrical wiring OPERATING THE REMOTE CONTROL Install 12V MN21 A23 battery included To prevent damage to transmitter remove the battery if not used for long periods Fig 14 Restore Power to Ceiling Fan A H M L Buttons These buttons are used to set the fan spe
6. o rod being sure that crass pin is in correct position the set screw on hanger ball is tight and wires are not twisted 8 Now lift the motor assembly into position and pare the hanger ball into the hanger bracket otate until the Check Tab has dropped into the Registration Slot and seats firmly The entire motor assembly should not rotate if this is done correctly 9 Remove protective plastic sleeve from the motor shaft and attach your wooden blades mele this step if you have metal blades as they should already have been installed Make sure that the set screw in the blade hub is counter sunk into the bore hole into the shaft of the motor MAKING THE ELECTRICAL CONNECTIONS Warning The power should have already been disconnected Follow the steps below to connect the fan to your household wiring Use the wire nuts supplied with your fan Secure the wire nuts with electrical tape Make sure there are no loose strands or connections NOTE The Hand Held Remote Control units included with your ceiling fan are equipped with 16 code combinations to prevent possible interference from or to other remote units The frequency switches on your Receiver and Transmitter units have been preset at the factory Please re check to make sure the switches on both units are set to the same positions The frequency settings should be changed only in case of interference or if a second or more remote controlled ceiling fans are installed
Download Pdf Manuals
Related Search