AireRyder FN52996OR Use and Care Manual
Contents
1. Unpack your fan and check the contents You should have the following items 1 Mounting Bracket 2 Fan Fixture Set 3 Housing 4 Blade Holder X5 5 Fan Blade X5 6 Switch Box Cover 7 Assembly Kit 8 Installation Instructions Dimension Reference A 8 1 4 in B 6 1 8 in C 11in D 5 3 8 in aireRyder F A N 101203 Exploded View Detail Blade Holder ico _ Mounting Bracket Mounting Bar Fan Fixture Set Housing aireRyder F A N 101203 Safety Instructions READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS All set screws of the fan must be checked and retightened where necessary before installation To reduce the risk of personal injury do not bend the blade brackets when installing the brackets balancing the blades or cleaning fan Do not insert foreign objects in between rotating fan blades Before changing the fan direction turn off the fan and wait for the fan blades to stop completely f a stationary appliance is not provided with a supply cord and a plug or with other means for disconnection from the mains supply having a contact separation of at least 3 mm in all poles that means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules NOTE The safeguards provided by these safety instructions and by the separate in2. THIS FAN MUST BE INSTALLED WITH A WALL CONTROL SWITCH SAVE ALL INSTRUCTIONS NOTE The fan weight is 13 8 lb 6 2 kg Be sure the outlet box you are using is securely attached to the building structure and can support the full weight of the fan Failure to do so can result in serious injury Installation Steps Turn OFF the electric power at the main fuse or circuit breaker box Mounting Bar Attach hang motor assembly onto mounting bracket Insert the EndA of mounting bar through the loop hole of the mounting plate for hands free wiring See Fig 4 1 and Fig 4 2 Unscrew the locked screws locked washers and screws from mounting bracket Mounting Bracket and Washers Tighten the mounting bracket to the outlet box with 2 mounting screws and washers To reduce the risk of fire electric shock or personal injury mount to the outlet box marked Acceptable for fan support and use mounting screws provided with the outlet box NOTE Pull the electrical wires from the outlet box through the center hole of the mounting bracket for motor wiring installation Mounting Bracket BORFA End A After install Before install Make wire connections box with a wire nut with a wire nut PAGE 1 3 1 The white motor wire to the white wire from the outlet box with a wire nut 2 The black motor wire and blue wire to the black hot wire from the outlet 3 The ground wire from the outlet box
3. aireRyder LIMITED LIFETIME WARRANTY Model No FN52996 aireRyder ORIGINAL CEILING FAN LIMITED LIFETIME WARRANTY The limited lifetime warranty covers this ceiling fan for residential use by the original purchaser against defects in material or workmanship as follows If your aireRyder Ceiling Fan motor fails at any time during the lifetime of the original purchaser due to defects in material or workmanship we will provide a replacement part free of charge If your Fan motor fails at any time within one year after the original date of sale to the original purchaser due to defects in material or workmanship we will provide labor to repair the defect with the exception of take down reinstallation free of charge The original purchaser will be responsible for all labor costs after this one year period If no replacement parts are provided for any part of your Fan motor that fails at any time during your lifetime due to defects in material or workmanship we will refund the original purchase price of your Fan If your Fan blades reverse switch or any accessory except glass globes and light bulbs fails at any time within one year after the original date of purchase due to a defect in material and workmanship we will repair or if we choose replace the defective blades switch or accessory free of charge with the exception of take down reinstallation services If the original purchaser ceases to own the Fan this warranty and any impli
4. ate when switch is in the middle 4 Make sure that the wall control is turned ON oO 2 If fan sounds noisy 1 Make sure all screws in motor housing are snug not over tightened 2 Make sure the screws which attach the fan bladeholder to the motor are tight 3 Make sure wire nut connectors in switch housing are not rattling against each other or against the interior wall of the switch housing CAUTION Make sure main power is turned off before entering switch housing 4 If using an optional ceiling fan light kit check to be sure the screws securing the glassware are finger tight Check to be sure light bulb is tight in socket and not touching glass shade s If vibration persists from glass remove glass and install a 1 4 in wide rubber band on glass neck to act as an insulator Replace glass and tighten screws against rubber band 5 Some fan motors are sensitive to signals from Solid State variable speed controls DO NOT USE a Solid State variable speed control 6 Allow break in period of 24 hours Most noises associated with a new fan will disappear after this period 3 If fan wobbles All blades are weighed and grouped by weight Natural woods vary in density which could cause the fan to wobble even though all blades are weight matched The following procedures should eliminate most of the wobble Check for wobble after each step 1 Check that all blades are screwed firmly into blade holders 2 Check that all blade holde
5. ed warranty including but not limited to any implied warranty of merchantability or fitness for a particular purpose become void This warranty and any implied warranty including but not limited to any implied warranty of merchantability or fitness for a particular purpose do not cover glass globes light bulbs or finish on any metal portions of the Fan This warranty is in lieu of express warranties The duration of any implied warranty of merchantability or fitness for a particular purpose with respect to any aireRyder Ceiling Fan motor blades switch or accessories is expressly limited to the period of the express warranty set forth above for such motor blades switch or accessories This warranty excludes defects malfunctions or failures of any aireRyder Ceiling Fan that are caused by repairs by persons not authorized by us use of parts or accessories not authorized by us mishandling improper installation modifications or damage to the Fan while in your possession or unreasonable use including failure to provide necessary maintenance In no event shall aireRyder Fan be liable for consequential or incidental damages Some states do not allow the exclusion or limitation of consequential or incidental damages in which case the above limitation or exclusion may not apply This warranty gives you specific legal rights and you may also have other rights which vary from state to state aireRyder F A _ N Package Contents
6. ith motor screws and washers eee Make sure the wires of the fan light in the switch box are capped with wire nuts Secure the switch box cover with the switch box screws Reverse Slide Switch Forward Fig 15 b The slide switch sets the direction of fan rotation Select the direction of fan rotation you need by sliding the switch Push the slide switch bottom for Forward and top for Reverse CAUTION If you install a Wall Control for this fan make sure to use the pull chains to select the high position for the fan speed and the on position for the fan light Turn ON the electric power at the main fuse or circuit breaker box a i re aireRyder er F A N PAGE 2 3 101203 Trouble Shooting Guide If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly installation or wiring In some cases these installation errors may be mistaken for defects If you experience any faults please check this Trouble Shooting Guide If a problem cannot be remedied or you are experiencing difficulty in installation please call our Customer Service Department PROBLEM SUGGESTED REMEDY 1 If fan does not start 1 Check main and branch circuit fuses or circuit breakers 2 Check line wire connections to fan and switch wire connections in switch housing CAUTION Make sure main power is turned off Make sure forward reverse switch is firmly in bottom or top position Fan will not oper
7. rs are tightened securely to motor 3 Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box is mounted firmly to ceiling joist 4 Most fan wobble problems are caused when blades are not equally level To check the blade levels select a point on the ceiling above the tip of any blade Measure the distance from the ceiling to the blade tip to an accuracy of 1 8 inch Rotate the blades until the next blade is in the measuring position Repeat measurement for each blade If all blade levels are not equal you can adjust blade levels by the following procedure To adjust a blade tip down insert a washer not supplied between the blade and blade holder at the screw closest to the motor To adjust a blade tip up insert washer not supplied between the blade and blade holder at the two screws farthest from the motor 5 If blade wobble is still noticeable interchanging two adjacent side by side blades can redistribute the weight and possibly result in smoother operation 1 Check blue wire from fan to make sure it is connected to hot wire from house 2 Check for loose or disconnected wires in fan switch housing 3 Check for loose or disconnected wires in light kit 4 Check for faulty light bulbs CAUTION Make sure main power is turned off before entering switch housing 4 If light does not work aireRyder F A N PAGE 3 3 101203
8. stallation instructions are not meant to cover all possible conditions and situations that may occur It must be understood that common sense caution and care are factors which can not be built into this product These factors must be supplied by the person s installing caring for and operating the fan WARNING TO AVOID RISK OF ELECTRIC SHOCK BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE TURNING OFF THE ELECTRICAL POWER BY USING THE LIGHT SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK TO REDUCE THE RISK OF INJURY INSTALL THE FAN SO THAT THE BLADES ARE AT LEAST 7 FEET 2 1 METERS ABOVE THE FLOOR AND AT LEAST 18 INCHES 0 5 METERS FROM THE TIP OF THE BLADES TO THE WALL TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY MOUNT TO OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE ANSI NFPA 70 1999 AND LOCAL CODES IF YOU ARE UNFAMILIAR WITH THE METHODS OF INSTALLING ELECTRICAL WIRING SEEK THE SERVICES OF A QUALIFIED LICENSED ELECTRICIAN aireRyder F A N 101203 INSTALLATION INSTRUCTIONS IMPORTANT BEFORE YOU BEGIN INSTALLING THE FAN CAREFULLY READ ALL INFORMATION ON THE SEPARATE SHEET SAFETY INSTRUCTIONS AS WELL AS THE FOLLOWING INSTALLATION INSTRUCTIONS IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
9. to the ground wire from the motor After making the wire connections the wires should be spread apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box After the connections have been made the wires should be turned upward and pushed carefully up into the outlet box aireRyde F A N Cc oO 101203 The decorative housing has two mating Screw amp Lock Washer slots and two mating holes Position both Mounting Bracket slots on the decorative housing directly under and in line with two screws and washers in the mounting bracket Lift the decorative housing allowing the two screws and washers to slide into the mating slots Rotate the decorative housing counterclockwise until both screws from the mounting bracket drop into the slot recesses Tighten screws securely SS Install the other two screws and washers Decorative Housing TA into the mating holes of the mounting bracket and tighten to secure the decorative housing to the mounting bracket lt Locked Washer Locked Screw Attach the mounting bar to the mounting bracket with the locked washers and locked screws using a screwdriver Tighten the three locked screws securely Blade Screw Blade Holder Motor Screw Tighten blades to blade holders by Secure blade holders to the motor SWEN BOK SETEM using blade screws w
Download Pdf Manuals
Related Search