AireRyder FN52455OBB Instructions / Assembly
Contents
1. Slide Hanger Pin through holes of Collar and Downrod Remove the Lock Pin and take off the Hanger Pin Insert and tighten the two Collar Screws Slide Lock Pin into Hanger Pin until it locks into position PAGE 1 5 Thread the motor wires through the canopy downrod stand cover and downrod Hanger Bracket Hang the fan on hanger bracket and make sure the slot of hanger ball is snapped into the chip of hanger bracket exactly Note For slope ceiling installation make sure the slot of hanger ball and the chip of hanger bracket is face down aireRyde F A N oO 090406 Receiver Antenna Receiver aw Hanger Bracket There is a frequency setter respectively in the transmitter and receiver This DIP Switch is a 4 key unit Fig 14 All keys were set at ON position in the beginning Set the keys to a different code Make sure the same numbered keys are switched ON for both DIP Switches Fig 14a Take note that the ON position may have different orientation in each Hanger Bracket Antenna e DO NOT CUT Hanger OR SPLICE aood Member Ceiling Joist i Ceiling as KN i Gi Flat Washer Junction Box Dry Wall Sand Hanger Bracket Safety Cable Ball Code example 1 ON 2 OFF 3 ON 4 OFF on both DIP Switches Move Ground Wires a Outlet Box wires b and Motor Wires c away from the center of the Hanger Bracket2. Then slide Receiver through Hanger Bracket as shown Antenna end first until it is centered Finally cut Motor Wires c to length needed for connections Make wire connections 1 The Motor white wire to the white To Motor N wire from Receiver with a wire nut 2 The Motor black wire to the black To Motor L wire from Receiver with a wire nut 3 The Motor blue wire to the blue For Light wire from Receiver with a wire nut 4 The white wire from Outlet Box to the red AC in N wire from Receiver with a wire nut 5 The black wire from Outlet Box to the red AC in L wire from Receiver with a wire nut 6 The ground wire from Outlet Box to the green ground wire from the Hanger Ball and the green ground wire from the Hanger Bracket with a wire nut Make sure all of wire nuts are connected firmly Tuck all wire nuts and wires carefully up into the Outlet Box EXCEPT antenna which should remain outside Outlet Box Attach the loop at the end of the safety cable to the ceiling surface then secure it with a flat washer and dry wall screw Make sure the flat washer and dry wall screw are covered by the fan canopy aireRyde PAGE 2 5 F AN c O 090406 Hanger Bracket Screw Washer Blade Screw Plastic Insert i Blade Holder Motor Screw Attach the canopy to the hanger Tighten blades to blade holders by Secure blade holders to the motor with bracket then secure it with four using blade sc
3. the fan blades to stop completely f a stationary appliance is not provided with a supply cord and a plug or with other means for disconnection from the mains supply having a contact separation of at least 3 mm in all poles that means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules NOTE The safeguards provided by these safety instructions and by the separate installation instructions are not meant to cover all possible conditions and situations that may occur It must be understood that common sense caution and care are factors which can not be built into this product These factors must be supplied by the person s installing caring for and operating the fan WARNING TO AVOID RISK OF ELECTRIC SHOCK BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE TURNING OFF THE ELECTRICAL POWER BY USING THE LIGHT SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK TO REDUCE THE RISK OF INJURY INSTALL THE FAN SO THAT THE BLADES ARE AT LEAST 7 FEET 2 1 METERS ABOVE THE FLOOR AND AT LEAST 18 INCHES 0 5 METERS FROM THE TIP OF THE BLADES TO THE WALL TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY MOUNT TO OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE ANSI NFPA 70 1999 AND LOCAL CODES I
4. F YOU ARE UNFAMILIAR WITH THE METHODS OF INSTALLING ELECTRICAL WIRING SEEK THE SERVICES OF A QUALIFIED LICENSED ELECTRICIAN aireRyder F_ A N 090406 INSTALLATION INSTRUCTIONS IMPORTANT BEFORE YOU BEGIN INSTALLING THE FAN CAREFULLY READ ALL INFORMATION ON THE SEPARATE SHEET SAFETY INSTRUCTIONS AS WELL AS THE FOLLOWING INSTALLATION INSTRUCTIONS IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN THIS FAN MUST BE INSTALLED WITH A WALL CONTROL SWITCH SAVE ALL INSTRUCTIONS NOTE The fan weight is 23 3 Ib 10 5 kg Be sure the outlet box you are using is securely attached to the building structure and can support the full weight of the fan Failure to do so can result in serious injury Installation Steps Turn OFF the electric power at the main fuse or circuit breaker box Wood Member 2 x 4 Approx Ceiling Joist Junction Box Hanger Bracket Tighten the hanger bracket to the outlet box with two mounting screws Make sure the outlet box is securely installed so that it will be able to support at least the fan weight WARNING MOUNT ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT Lock J A For ceiling mount only Attach the canopy to the housing with three ceiling mount screws Go to Fig 9 for the next step Downrod 2 AD Canopy Downrod Stand over Motor wines o Hanger wr al B p S Collar Le Insert the Downrod into the Collar
5. ackage Contents Unpack your fan and check the contents You should have the following items 1 Hanger Bracket 2 Canopy 3 Downrod Set Includes Hanger Ball 6 in Downrod Hanger Pin amp Lock Pin 4 Downrod Stand Cover 5 Fan Fixture Set 6 Switch Box Cover 7 Fan Light Set 8 Fan Blade X5 9 Blade Holder X5 10 Remote Control Set Includes Transmitter amp Receiver 11 Assembly Kit 12 Installation Instructions 13 Bulb Type B Max 60W X3 Dimension Reference Installed with 6 in Downrod A 28 B 17in C 2 2 5in D 12 1 8 in E 5 7 8 in 090406 Exploded View Detail Hanger Bracket Receiver Canopy Hanger Ball Downrod Downrod Stand Cover Lock Pin Collar Housing Fan Light Truple Mount Drawing Ceiling Mount Downrod Mount Slope Ceiling Mount Up to 23 degrees aireRyder F A N 090406 Safety Instructions READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS All set screws of the fan must be checked and retightened where necessary before installation To reduce the risk of personal injury do not bend the blade brackets when installing the brackets balancing the blades or cleaning fan Do not insert foreign objects in between rotating fan blades Before changing the fan direction turn off the fan and wait for
6. aireRyder LIMITED LIFETIME WARRANTY Model No FN52455 aireRyder ORIGINAL CEILING FAN LIMITED LIFETIME WARRANTY The limited lifetime warranty covers this ceiling fan for residential use by the original purchaser against defects in material or workmanship as follows lf your aireRyder Ceiling Fan motor fails at any time during the lifetime of the original purchaser due to defects in material or workmanship we will provide a replacement part free of charge If your Fan motor fails at any time within one year after the original date of sale to the original purchaser due to defects in material or workmanship we will provide labor to repair the defect with the exception of take down reinstallation free of charge The original purchaser will be responsible for all labor costs after this one year period If no replacement parts are provided for any part of your Fan motor that fails at any time during your lifetime due to defects in material or workmanship we will refund the original purchase price of your Fan lf your Fan blades pull chain switch reverse switch or any accessory except glass globes and light bulbs fails at any time within one year after the original date of purchase due to a defect in material and workmanship we will repair or if we choose replace the defective blades switch or accessory free of charge with the exception of take down reinstallation services If the original purchaser ceases to own the Fan this warr
7. anty and any implied warranty including but not limited to any implied warranty of merchantability or fitness for a particular purpose become void This warranty and any implied warranty including but not limited to any implied warranty of merchantability or fitness for a particular purpose do not cover glass globes light bulbs or finish on any metal portions of the Fan This warranty is in lieu of express warranties The duration of any implied warranty of merchantability or fitness for a particular purpose with respect to any aireRyder Ceiling Fan motor blades switch or accessories is expressly limited to the period of the express warranty set forth above for such motor blades switch or accessories This warranty excludes defects malfunctions or failures of any aireRyder Ceiling Fan that are caused by repairs by persons not authorized by us use of parts or accessories not authorized by us mishandling improper installation modifications or damage to the Fan while in your possession or unreasonable use including failure to provide necessary maintenance In no event shall aireRyder Fan be liable for consequential or incidental damages Some states do not allow the exclusion or limitation of consequential or incidental damages in which case the above limitation or exclusion may not apply This warranty gives you specific legal rights and you may also have other rights which vary from state to state aireRyder F A _ N P
8. ck line wire connections to fan and switch wire connections in switch 2 If fan sounds noisy 1 Make sure the screws which attach the fan bladeholder to the motor are tight Make sure wire nut connectors in switch housing are not rattling against each oF 6 Check main and branch circuit fuses or circuit breakers housing CAUTION Make sure main power is turned off Make sure forward reverse switch is firmly in right or left position Fan will not operate when switch is in the middle Make sure that the wall control is turned ON Make sure all screws in motor housing are snug not over tightened other or against the interior wall of the switch housing CAUTION Make sure main power is turned off before entering switch housing If using an optional ceiling fan light kit check to be sure the screws securing the glassware are finger tight Check to be sure light bulb is tight in socket and not touching glass shade s If vibration persists from glass remove glass and install a 1 4 in wide rubber band on glass neck to act as an insulator Replace glass and tighten screws against rubber band Some fan motors are sensitive to signals from Solid State variable speed controls DO NOT USE a Solid State variable speed control Allow break in period of 24 hours Most noises associated with a new fan will disappear after this period 3 If fan wobbles All blades are weighed and grouped by weight Natural woods vary
9. es onto the glass holders and then secure them with socket rings Install bulbs included See relamping label at socket area or packaging for maximum allowed wattage lt gt Forward Reverse Slide Switch Turn ON the electric power at the The slide switch sets the direction of fan rotation Select the direction main fuse or circuit breaker box of fan rotation you need by sliding the switch Push the slide switch left for Forward and right for Reverse Install the battery to the transmitter 9V not included Press HI to turn on the fan at high speed Press MED button to turn the fan in medium speed Press LOW button to turn the fan in low speed Press FAN OFF button to turn off the fan Press and release the e button quickly to turn on off the fan light By using the dimmer function press and hold the a button to adjust the illumination of light PAGE 4 5 aireRyder F A N 090406 Trouble Shooting Guide If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly installation or wiring In some cases these installation errors may be mistaken for defects If you experience any faults please check this Trouble Shooting Guide If a problem cannot be remedied or you are experiencing difficulty in installation please call our Customer Service Department PROBLEM SUGGESTED REMEDY 1 If fan does not start T Che
10. in density which could cause the fan to wobble even though all blades are weight matched The following procedures should eliminate most of the wobble Check for wobble after each step 1 4 4 If light does not work Check that all blades are screwed firmly into blade holders 2 3 Check that all blade holders are tightened securely to motor Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box is mounted firmly to ceiling joist Most fan wobble problems are caused when blades are not equally level To check the blade levels select a point on the ceiling above the tip of any blade Measure the distance from the ceiling to the blade tip to an accuracy of 1 8 inch Rotate the blades until the next blade is in the measuring position Repeat measurement for each blade If all blade levels are not equal you can adjust blade levels by the following procedure To adjust a blade tip down insert a washer not supplied between the blade and blade holder at the screw closest to the motor To adjust a blade tip up insert washer not supplied between the blade and blade holder at the two screws farthest from the motor If blade wobble is still noticeable interchanging two adjacent side by side blades can redistribute the weight and possibly result in smoother operation Check blue wire from fan to make sure it is connected to hot wire from house Check for loose or disc
11. onnected wires in fan switch housing Check for loose or disconnected wires in light kit Check for faulty light bulbs CAUTION Make sure main power is turned off before entering switch housing If the fan light shuts off shortly after being switched on it may be due to excessive current demand Turn off power to the fan and replace the light bulbs with lower wattage bulbs Turn on power to the fan using the pull chain wall switch or remote control whichever is installed on the particular fan aire aireRyder er F A N PAGE 5 5 090406
12. rews and washers motor screws and washers screws and washers NOTE Before installing blade holders to the motor please remove the plastic inserts Assembly without fan light Make sure the wires of the fan light in the switch box are capped with wire nuts Switch z Secure the switch box with the switch box screws Screw Note To install the fan light skip this step and proceed to Fig 17 Fan Light Installation WARNING As per EPACT 2005 requirements this fan light has a built in current limiting device to conserve energy The fan light will not operate if the combined wattage of the installed bulbs exceeds 190 Watts If the fan light shuts off shortly after being switched on it may be due to excessive current demand Turn off power to the fan and replace the light bulbs with lower wattage bulbs Turn on power to the fan using the pull chain wall switch or remote control whichever is installed on the particular fan Bulb Type B Max 60W UT UY included Socket Ring Make wire connections using wire nuts The blue wire from the switch box to the black wire from fan light The white wire from the switch box to the white wire from fan light Carefully put the wires into the switch box Secure the fan light onto the switch box using the switch box screws a i re R d C FAN 47 Oo PAGE 3 5 090406 Attach the glass shad
Download Pdf Manuals
Related Search