Casablanca C43G11L Installation Guide
Contents
1. Receiver Using an orange wire connector from the hardware bag Connect the 3 grounding wires green green yellow stripe or bare copper coming from the ceiling downrod and ceiling bracket green yellow stripe Mo aX4 uUaas6 Bulpunosb du s Q OO oO gt 5 lt oO 0 Place the receiver on top of the downrod assembly as shown Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of Refer to CAUTION c 1 on pg 2 8 the outlet box and the ungrounded wires on the other side of the outlet box J M8511 01 10 30 14 Casablanca Fan Company Wiring continued Using the wire connectors from the remote control hardware bag e Connect the white wire from the receiver marked common out to the white wire from fan Connect the black wire from the receiver marked fan out to the black wire from the fan Connect the blue wire from the receiver marked light out to the blue wire from the fan The red wire from the receiver will not be used it has a pre installed wire terminator Refer to CAUTION c 1 on pg 2 no UOLWUWWOD d 1UM M8511 01 www CasablancaFanCo com 1 888 227 2178 Using an orange wire connector from the hardware bag e Connect the black wire ungrounded from the ceiling to the black wire from the receiver marked2. LEL KEE A www CasablancaFanCo com 1 888 227 2178 l l What to Expect with Congratulations on purchasing your new Your Installation Tools Needed Casablanca ceiling fan It will provide comfort and performance in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world To register your fan please visit www CasablancaFanCo com register Save your receipt for proof of purchase Blades l Light Kit Operation M8511 01 10 30 14 Casablanca Fan Company What to Expect with Your Installation Must be able to secure the fan to building structure or fan rated outlet box You may need a friend to help you Check box to see fan weight If you are unfamiliar with wiring use a qualified electrician D Know your wiring i Ceiling angles greater than 34 will require an Angled Mounting Kit See page 4 for details A Assess ceiling angle 30 inches from blade tip to nearest wall or obstruction 7 feet from bottom edge of blade to the floor A Assess location Standard Downrod for ceilings 8 10 feet high Shorter Downrod for fans installed close to ceiling EJ Longer Downrod
3. Carefully lift other socket inward and lift the onto the sockets the globe assembly as far as it See next page for fan bulb up until it fits into place will go then rotate it counter operation instructions clockwise until it is held into place by the three tabs M8511 01 10 30 14 Casablanca Fan Company Operation Battery Holder Battery Door Before operating the wall control press on the battery door to eject it Unscrew the battery holder Insert the battery found in the control hardware bag with the positive side facing downward Reinstall the battery holder and reinsert the battery door into the wall control M8511 01 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 The remote transmitter should already be paired to the receiver and ready to use Note If your need to pair your remote turn fan power off and back on at the circuit breaker Within three minutes press and hold both the Fan Off button and the 4 button for four seconds to pair the remote To prevent faulty operation please disconnect power from all other ceiling fans within range while pairing Operation continued Lights Down Reverse Battery Holder Quickly press the up or down arrow to turn the lights off and on Hold the up or down arrow to raise or dim the light level The reverse button changes the direction that the blades turn The power button turns the f
4. a nanotechnology coating that repels dust For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning agents may damage the finishes Light Kit Align the screw holes in the light kit fitter with the screw holes in the fan s mounting plate Attach the light kit fitter to the mounting plate using the three light kit fitter screws found in the hardware bag Using the ceramic wire connectors connect the blue wire from the fan to the black wire from the light kit assembly Connect the white wire from the fan to the white wire from the light kit assembly Note Be sure to use the CERAMIC wire connectors to avoid fire hazard M8511 01 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Light Kit Assembly Screw Align the screw holes and attach the light kit assembly to the light kit fitter using the three light kit assembly screws found in the hardware bag Make sure the light kit fitter and light kit assembly are securely attached Failure to properly secure all assembly screws could result in the light kit fixture falling l J Light Kit continued www CasablancaFanCo com EZA To install the halogen bulb angle To install the bulb shield raise Align the the notches in the one end of the bulb into the the bulb shield to the light kit globe assembly with the tabs in socket as shown then push the assembly and push the clips the light kit fitter
5. brushes or cloths to prevent scratching Cleaning products may damage the finishes www CasablancaFanCo com 1 888 227 2178 Troubleshooting Fan doesn t work Excessive wobbling Noisy Operation Remote doesn t work e Press a fan speed button 1 4 e Tighten all of the blade screws Check the circuit breaker to ensure the power is turned on Check the wall control battery Make sure that you have paired the wall control Make sure the blades spin freely Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on pages 9 10 Check the wire connection in the light kit assembly until they are snug Turn the power off support the fan carefully and check that the hanger ball is properly seated Use the provided balancing kit and instructions to balance the fan If you have multiple remotes or multiple remote controlled fans installed on the same circuit breaker and you are experiencing interference or faulty operation of your remote controls please go to www CasablancaFanCo com FAQs and click How do I properly install multiple remote controlled fans for information on how to correct this issue e Tighten the blade screws until they are snug e Check to see if any of the blades are cracked If so replace all of the blades AUTHORIZED SERVICE CENTERS For the most updated list of Casablanca Authorized Servic
6. vaulted or angled ceiling a Longer Downrod most common Mounting Kit M8511 01 Raat 10 30 14 Casablanca Fan Company Ceiling Bracket 4 aay For angled ceilings point opening toward peak If you are unable to do this call Technical Support at 1 888 227 2178 Make sure all four bumpers are still attached Refer to warning w 1 on pg 2 i M8511 01 Use wood screws included when securing to support structure with approved electrical outlet box Drill 9 64 pilot holes in support structure to aid in securing ceiling bracket with hardware found in the amp hardware bag 5 e 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Use machine screws provided with outlet box when securing to existing ceiling fan rated outlet box Make sure it is securely installed and is acceptable for fan support of 31 8 kg 70 Ibs or less To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location Downrod www CasablancaFanCo com 1 888 227 2178 Standard Downrod skip to next page for ceilings 8 10 high If you need a different downrod length follow these steps Longer Steps 1 5 to remove standard downrod pipe Downrod for angled ceilings or ceilings 10 or higher Included pre assemble
7. an off and on Reverse Button The reverse button on the wall control changes the air flow pattern In warm weather use a downward air flow pattern In cold weather use b upward air flow pattern M8511 01 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 The Safe Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out To use Safe Exit e Press the fan power button off for at least three seconds to initiate the Safe Exit Mode The lights will flash for visual confirmation e The lights will stay on 50 brightness for 20 seconds and then begin to dim After a total of 30 seconds the lights will be completely off Note For CFL lighting the lights will stay on 100 brightness for 30 seconds After a total of 30 seconds the lights will be completely off Maintenance amp Cleaning Be sure to turn off power to the fan before performing any maintenance or relamping Changing the bulb carefully rotate the globe assembly clockwise and lower it from the light kit Remove the bulb shield Press in on the light socket to slide one end of the bulb out and remove the bulb Install a new halogen bulb of the same type and wattage and reinstall the globe assembly M8511 01 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Cleaning the fan use soft
8. d Shorter Downrod for fans installed close to ceiling Included Sold Separately M8511 01 10 30 14 Casablanca Fan Company Downrod continued Remove the pre installed setscrew so that the downrod can be inserted www CasablancaFanCo com 1 888 227 2178 T U YN O O Hand tighten the downrod at The wires can be cut but least 4 5 full turns until it stops leave at least 8 extending from the top of the downrod M8511 01 10 30 14 Casablanca Fan Company Tighten the setscrew with pliers DO NOT HAND TIGHTEN If the setscrew is not tightened securely the fan may fall Downrod continued R Lower the adapter cover over the downrod until it rests flush against the motor housing Align the screw holes on the adapter cover with the screw holes on the motor housing and install the three adapter cover screws found in the hardware bag Note The adapter cover is not used for low profile mounting Put the wires and downrod through the canopy Let the canopy sit loosely on top of the fan DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES Place the downrod ball into the slot in the ceiling bracket M8511 01 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Note To connect the wires hold Y the bare metal leads together and place a wire connector over them 4 then twist clockwise until tight
9. e Centers visit www CasablancaFanCo com or call toll free 1 888 227 2178 M8511 01 10 30 14 Casablanca Fan Company e Install a fresh battery in the wall control e Make sure you have paired the remote
10. for ceilings 10 feet or higher LA Select a downrod length 2 M8511 01 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Read and Save These Instructions This product conforms to UL Standard 507 A WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Casablanca Solid State Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Casablanca replacement parts This equipment has been tested and found to comply with the l
11. imits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Tools Needed LI Ladder Pliers Wire Strippers Power Drill 9 64 Drill Bit optional optional If mounting to a support structure you will also need these tools 3 M8511 01 Raat 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 amp e H Screwdrivers VO Mounting Options 1 888 227 2178 R A l O i egoe U p If you have a flat ceiling Hang your fan by a standard downrod included Standard Support Support Mounting Structure Tae O If you have an angled ceiling SAN D 1 You will need a longer downrod sold separately Outlet Box 2 If your ceiling angle is greater than 34 you will Angled 2 required also need an Angled Mounting Kit sold separately Mounting N Outlet Box required Mounting Use the three steps below to determine if your ceiling angle is greater than 34 Use Standard Mounting Use Angled Mounting BOTH Ceiling amp Wall or Low Profile Mounting to hang the fan from a You need ONLY to hang the fan from a flat ceiling
12. live in papunosb ayyM papunosbun y2ejq Connect the white wire grounded from the ceiling to the white wire from the receiver marked neutral in or common in ul Je4ynNaU PyM Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box e 10 30 14 Casablanca Fan Company Wall Control Drill Holes W Drywall Anchors Painter s Tape 1 Tape the provided wall control 1 Using a 9 64 drill bit drill a hole template with painter s tape at in each screw cut out on the wall the desired installation area control template 2 Drill holes inside the four 2 Using a hammer tap a drywall corners of the template anchor found in the wall control Note Make sure the wall hardware bag into each hole control template is level before until the drywall anchor is flush proceeding to the next step with the wall If you are using a outlet box for wall control installation the wires coming from the wall control must be grounded using the attached green wire If not placed in an outlet box cap the green wire coming from the wall control with an included wire nut l e M8511 01 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Template 1 Using a drywall punch saw 1 In
13. sert the wall control into the cut out the interior shape of R dry wall cut out the template using one of 2 Align the screw holes in the wall the four drilled corners asa control with the drywall anchors starting point 3 Poa A Selah a Phillips Head screwdriver 2 Remove the template and the to ae the two cover plate cut out section of drywall screws found in the wall control hardware bag through the wall control and into the drywall anchors This device complies with Part 15 of the FCC Rules Operation is subject to the following conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation l e www CasablancaFanCo com 1 888 227 2178 Position the canopy so that when Lift the canopy into place so that Insert the two canopy screws lifted into place the canopy fits into the screw holes are aligned found in the hardware bag the hanging bracket as shown Note Fan style may vary M8511 01 10 30 14 Casablanca Fan Company Blades Insert a blade into the motor housing as shown Attach each blade to the fan using two blade grommets found in the W hardware bag and two blade assembly screws found in the A hardware bag M8511 01 10 30 14 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 i aJa Your blades are shielded with Dust Armor which is
Download Pdf Manuals
Related Search