Laura Ashley PXS211 Instructions / Assembly
Contents
1. Assembly Instructions Mallow Pierced Pendant PXS211 WARNING BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE NOTE 1 Before installing consult local electrical codes for wiring and grounding requirements 2 READ AND SAVE THIS INSTRUCTION For Swag Light 1 Open the hardware package which is marked For Swag Light 2 Installing two ceiling hooks on ceiling One of them o N must be fastened on the edge of ceiling as Fig 1 For plaster or plaster board ceilings See Fig 2 a Drill a 5 8 hole in the ceiling where it is to be installed b Insert the nipple into the ceiling hook c Secure the toggle bolt onto the nipple d Measure the thickness of ceiling squeeze two flaps of toggle bolt together and adjust the length L from toggle bolt to ceiling hook as you measured e Insert the toggle bolt through the drilled hole until the ceiling hook touches ceiling then secure the ceiling hook tightenly For wood ceilings minimum thickness size is 3 4 See Fig 3 a Select a place on the ceiling where a wood beam exists b Insert the dry wall screw into the ceiling hook c Screw the assembled ceiling hook into the wood beam Thread the cord and fixture grounding wire through the C spider of the shade attach the nipple of the socket to the C spider and secure it with the loop See the illustration as shown in For Pendant2. e 5 8 14 Turn on the power at the main fuse or circuit breaker box A 8 Smooth Wire ae 4 Ridged Wire Cord Canopy Page 2
3. k twist the locking tube open hook onto top end of Locking Tube the chain and the top loop Close back the locking tube of uel the loop lock i Cor 7 Weave the cord and the fixture grounding wire through the q L spkodk chain and the canopy L t 8 Measure about 8 of the cord A from the top of the A C Spider canopy then cut off the unnecessary cord Suter Shade 9 Slit the cord apart into two wires C about 4 from the top of the cord Then use a knife to peel off the insulation of the two wires at about 5 8 length B from the top of LC al the wires to expose the copper for wiring See Fig 4 10 Pull out the outlet wires and house grounding wire from the outlet box Make wire connections with wire nuts The smooth wire marked from the fixture to the black wire from the power source The ridged wire unmarked from the fixture to the white wire from the power source Attach the fixture grounding wire to the mounting strap with the green grounding screw Then connect it to the house grounding wire with the wire nut Carefully put the wires back into the outlet box 11 Attach the canopy to the mounting strap by inserting the screws then secure it with two bolt nuts 12 Carefully pull the inner shade downward in place from the outer shade 13 Install a bulb not included Note relamping label at socket I or packaging area for maximum allowed wattage Mee
4. page Cut the fixture grounding wire near the loop Take a certain length of chain you need then hang the links of chain to the ceiling hooks Thread the cord through the ceiling hooks Insert the plug into wall receptacle then control the lamp with the switch Page 1 PA Ceiling Hook DS e s Foe rT Switch y For Swag Light Fig 1 SS Ceiling Toggle Bolt Nipple gt N r a Ceiling Hook Fig 2 Fig 3 For Pendant 1 Open the hardware package which marked For Pendant 2 Thread two screws through the mounting strap then secure them with two lock nuts Adjust the length of the screws if necessary 3 Attach the mounting strap to the outlet box by using two Outlet Box House Grounding Wire Wire Nut Screw mounting screws Mounting Strap 4 Thread the cord and fixture grounding wire through the a Grounding C spider of the shade attach the nipple of the socket to l f Lock Nut the C spider and secure it with the loop fiture Grounding 5 Take one loop lock twist the locking tube open then hook Wire onto the loop and onto one end of the chain Close back canopy the locking tube of the loop lock 3 ans sae wa 6 Choose the length of the chain you need then take another a sha loop loc
Download Pdf Manuals
Related Search