Hampton Bay 14412 Instructions / Assembly
Contents
1. GG y H o FF g I Part Description Quantity AA Blade attachment hardware 3 16 in x 17mm screws and lock washer 10 BB Plastic wire nut 3 CC Balance kit not to scale 1 DD Mounting bracket screws preassembled 3 16 in x 1 2 in screws and lock washer 4 EE Remote control holder mounting screws 2 FF Remote control holder plugs preassembled 2 GG Blade support plates not to scale 3 HH Mounting ring screws preassembled 5 32 in x 8mm screws 3 Il Light kit plate screws preassembled 5 32 in x 8mm screws 4 5 HAMPTONBAY COM Please contact 1 800 527 0998 for further assistance Pre Installation continued PACKAGE CONTENTS A B C D E C z Part Description Quantity Part Description Quantity A Mounting bracket 1 G Receiver 1 B Fan motor assembly 1 H Remote control 1 C Blades 3 l Remote control holder 1 D Light kit mounting plate 1 J 100W halogen bulb 1 E Light kit plate 1 K 12V MN21 A23 battery 1 F Glass shade 1 Installation MOUNTING OPTIONS WARNING To reduce the risk of fire electric shock or personal injury mount the fan to an outlet box marked acceptable for fan support using the screws provided with the AN outlet box An outlet box commonly used for the support of lighting fixtures ma2. and hold the button to set the desired brightness The light button has an auto resume it will stay at the same brightness as the last time it was turned off INSTALLING THE REMOTE CONTROL HOLDER Remove the two remote control holder plugs FF from the remote control holder I Note that the plugs have unique tabs that allow them to fit only in one hole Attach the remote control holder I with the two remote control holder mounting screws EE Replace the two remote control holder plugs FF each into its own hole 15 HAMPTONBAY COM Please contact 1 800 527 0998 for further assistance Operation continued REVERSE SWITCH OPERATING INSTRUCTIONS The reverse switch is located on the surface of the switch housing This switch controls directions forward switch left or reverse switch right A Warm weather Counterclockwise Direction A downward air flow creates a cooling effect This allows you to set your air conditioner on a warmer setting without affecting your comfort NOTE Wait for the fan to stop before reversing the direction of the blade rotation Cool weather Clockwise Direction An upward air flow moves warm air off the ceiling This allows you to set your heating unit on a cooler setting without affecting your comfort a acn AE za SH NN Care and Cleaning Do Check the support connections br
3. Item 184 595 Model 14412 USE AND CARE GUIDE SOVANA 44 INCH CEILING FAN Questions problems missing parts Before returning to the store call Hampton Bay Customer Service 8 a m 6 p m EST Monday Friday 1 800 527 0998 HAMPTONBAY COM LISTED THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this ceiling fan We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Hampton Bay Table of Contents Table of Contents ccccccceseesesesesssesseeeseeeeesessssseseseeesenenes 2 Safety Information 1 1 7 00sssamaanaaaamanananaaaasaanann0naaa 3 Warranty QING RAT 4 Pre installation ssiiccscsiscsccsccssicsccesssscscecacsttenscacssvsescssastecee 4 Specifications maa N NANA 4 TOOS RE QUINGD vistri iiiar AA 4 Hardware INCIUMGG sisisi 5 Package GOntent siccisiicccccscecisessscesessccaesnscccessaceccnsscsesecreceesversenstes 6 Installalon wsisccsseciecccccscescescnsscnsseseeadeesaesedsceccccsezececwensnece 7 Assembly 2NA ABANGAN 8 HANGING the FAN sisisi 8 Setting up the Remote Control ul u uu mamana wanna wawawawa nawasa wannawa wana 9 Making the Electrical Connections ulumumummmmnnananuwunawananunununuwanawana 10 Finishing the Fan Motor Installation cccssssssssecssssssseeeeseas 11 Attaching the Fan Blades uuuumumummbub
4. RR marked AC in L from the receiver G Connect the white neutral wire UU from the ceiling to the white wire SS marked AC in N from the receiver G 10 If your outlet box JJ has a ground wire VV green or bare copper connect it to the fan ground wires WW otherwise connect the hanging ball ground wire to the mounting bracket A Secure the wire connection with a plastic wire nut BB provided After connecting the wires spread them apart so that the green and white wires are on one side of the outlet box JJ and black and blue wires are on the other side Carefully tuck the wire connections up into the outlet box JJ Assembly Finishing the Fan Motor Installation 5 Attaching the fan motor assembly to the mounting bracket Loosen two of the four mounting bracket screws DD from the mounting bracket A and remove the other two screws DD Remove the fan motor assembly B from the mounting bracket A hook and engage the key holes with the two mounting bracket screws DD previously loosened 6 Tightening the screws Install the two mounting bracket screws DD previously removed and tighten all four mounting bracket screws DD HAMPTONBAY COM Please contact 1 800 527 0998 for further assistance Assembly Attaching the Fan Blades Fastening the blade assemblies to th
5. ackets and blade attachments twice a year Make sure they are secure Because of the fan s natural movement some connections may become loose over time It is not necessary to remove the fan from the ceiling Clean your fan periodically Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or tarnishing Optional Apply a light coat of furniture polish to the wood blades Optional Cover small scratches with a light application of shoe polish Do not Do not use water when cleaning Water could damage the motor or the wood or possibly cause an electrical shock Do not apply oil to your fan or motor The motor has permanently lubricated sealed ball bearings 16 Troubleshooting panel box before you attempt any repairs Refer to step 4 WARNING Make sure the power is off at the electrical Making the electrical connections on page 10 Problem Solution The fan will not start Check main and branch circuit fuses or breakers Check line wire connections to the fan and switch wire connections in the switch housing Check to make sure the dip switches from the remote control and receiver are set to the same frequency The fan sounds noisy Make sure all motor housing screws are snug Make sur
6. around or cleaning the fan Do not use water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box All setscrews must be checked and retightened where necessary before installation this fan must only use a UC7067RC solid state speed control WARNING To reduce the risk of fire or electronic shock with a UC9050T wall control WARNING To reduce the risk of personal injury do not bend the blade arms also referred to as flanges when installing the brackets balancing the blades or cleaning the fan WARNING Do not insert foreign objects between rotating fan blades WARNING To reduce the risk of fire electric shock or personal injury mount the fan to the outlet box marked acceptable for fan support using the screws provided with the outlet box HAMPTONBAY COM Please contact 1 800 527 0998 for further assistance Warranty We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase b
7. de wobble is still noticeable 17 HAMPTONBAY COM Please contact 1 800 527 0998 for further assistance Service Parts Part Description Mounting bracket Fan motor assembly 3 blades Light kit mounting plate Light kit plate Glass shade Receiver Remote control Remote control holder 100W halogen bulb Alej Ilo mni m ojojo D gt 12V MN21 A23 battery ek YO Br CJ GG 18 Part Description BB Blade attachment hardware 3 16 in x 17mm screws and lock washers Plastic wire nut CC Balance kit DD Mounting bracket screws 3 16 in x 1 2 in screws and lock washers EE Remote control holder mounting screws FF Remote control holder plugs GG Blade support plates HH Mounting ring screws 5 32 in x 8mm screws Light kit plate screws 5 32 in x 8mm screws Questions problems missing parts Before returning to the store call Hampton Bay Customer Service 8 a m 6 p m EST Monday Friday 1 800 527 0998 HAMPTONBAY COM Retain this manual for future use 11MA0620 1H000001 C
8. e motor WARNING To reduce the risk of personal injury do not bend the blade arms while installing balancing the blades C or cleaning the fan Do no insert foreign objects between rotating fan blades C Insert a blade C through one of the slots in the bottom band Align the holes in the blade with the three holes in a blade support plate GG The raised holes in the blade support plate GG should face down Repeat this process to attach the other blades C 12 Assembly Installing the Light Kit 8 Attaching the light kit mounting plate to the mounting ring Remove one of three mounting ring screws HH from the mounting ring YY and loosen the other two screws Do not remove Place the key holes in the light kit mounting plate D over the two screws HH previously loosened from the mounting ring YY turn the light kit mounting plate D until it locks in place at the narrow section of the key holes Secure by tightening the two mounting ring screws HH previously loosened and the one HH previously removed HH 9 Attaching the light kit plate to the mounting plate While holding the light kit plate E under your fan B make the polarized plug connections White to white Black to black Install the light kit plate E onto the light kit mounting plate D with four l
9. e the screws that attach the fan blade arm to the motor hub are tight Make sure wire nut connections are not rattling against each other or the interior wall of the switch housing Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this time If using the ceiling light kit make sure the screws securing the glassware are tight Check that the light bulb is also secure Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket and outlet box The remote control is not working Do not connect the fan with wall mounted variable speed control s Check to make sure the dip switches from the remote control and receiver are set to the same frequency The fan wobbles Check that all blade and blade arm screws are secure Most fan wobble problems are caused when blade levels are unequal Check this level by selecting a point on the ceiling above the tip of one of the blades Measure from a point on the center of each blade to the point on the ceiling Rotate the fan until the next blade is positioned for measurement Repeat for each blade Measurement deviations should be within 1 8 in Run the fan for 10 minutes o Use the enclosed blade balancing kit if the bla
10. ight plate screws II provided Be sure to tighten all screws Il 13 HAMPTONBAY COM Please contact 1 800 527 0998 for further assistance Assembly Installing the Light Kit continued 1 Finishing the light kit assembly and mounting the glass shade WARNING Before starting installation disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box Turning power off using the fan switch is not sufficient to prevent electric shock Install the 100 Watt halogen bulb J included Raise the glass shade F up against the bottom of the fan housing B and secure it to the fan by the turning glass F clockwise until snug Do not overtighten Restore the power and your fan is ready for opera tion 14 Operation REMOTE CONTROL OPERATING INSTRUCTIONS Install a 12V MN21 A23 battery K included in to the remote control H To prevent damage to the remote control H remove the battery K if not used for long periods Restore power to the ceiling fan and test for proper operation HI MED LOW buttons These three buttons are used to set the fan speed as follows LOW Low speed MED Medium speed and HI High speed OFF button This button turns the fan off The Ces button turns the light ON or OFF and also controls the brightness setting Press and release the button to turn the light ON or OFF Press
11. o not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law Some states do not allow the exclusion of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer Contact the Customer Service Team at 1 800 527 0998 or visit www hamptonbay com Pre Installation SPECIFICATIONS Fan size Speed Volts Amps Watts RPM CFM N W G W C F Low 0 26 9 9 82 1322 14 8 05 kgs 9 11 kgs 44 in Medium 120 0 38 27 9 162 2591 99 17 71 Ibs 20 04 Ibs 1 834 ft High 0 40 48 3 226 3851 73 NOTE These are approximate measures They do not include amps and wattage used by the light kit TOOLS REQUIRED Wire stripper Electrical Tape D Phillips Flat blade Step screwdriver K screwdriver ladder Pre Installation continued HARDWARE INCLUDED NOTE Hardware shomn to actual size unless noted otherwise in the table below To f BB
12. ounting screws provided with the outlet box Attach the mounting bracket A to the outlet box JJ not included with the two screws and washers XX provided with the outlet box JJ Ensure the mount ing bracket A is tight and secured Assembly Setting up the Remote Control Preparing the receiver and remote control WARNING To avoid possible electrical shock ensure electricity is tumed off at the main fuse box before wiring CAUTION The frequency switches on the receiving unit are covered with a rubber cover Remove the rubber cover and then replace it after making any changes to the frequency switches CAUTION Do not use this fan with a wall light dimmer switch If you feel you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrician This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units The frequency switches on your receiver G and remote control H have been preset at the factory Please recheck to make sure the switches on the remote control H and the receiver G are set to the same position Any combination of settings will operate the fan as long as the remote control H and receiver G are set to the same position Insert the receiver G into the fan motor assembly B with the flat side of the
13. receiver G facing the ceiling HAMPTONBAY COM Please contact 1 800 527 0998 for further assistance Assembly Making the Electrical Connections Making the electrical connections WARNING To avoid possible electrical shock ensure electricity is turned off at the main fuse box before wiring including ground and that no bare wire is visible at the wire i WARNING Check to see that all connections are tight nuts except for the ground wire CAUTION Do not use with a wall light dimmer switch 20 feet from the remote control for proper signal transmission NOTE The fan must be installed at a maximum distance of A between the remote control and the fan s receiving unit Follow the steps below to connect the fan to your household wiring Use the plastic wire nuts BB with your fan Secure the wire nuts with electrical tape Ensure there are no loose strands or connections Motor to receiver electrical connections Connect the black wire QQ from the fan to black wire LL marked TO MOTOR L from the receiver G Connect the white wire 00 from the fan to the white wire NN marked TO MOTOR N from the receiver 6 Connect the blue wire PP from the fan to the blue wire MM marked For Light from the receiver G Receiver to house supply wires electrical connections Connect the black hot wire TT from the ceiling to the black wire
14. ubununuawauaununuawawaununaauananausuananawan 12 Installing the LighiiKihama maamin iman 13 Operation a NAGA ced scesccnccsceaeseceeseeceeastauaes 15 Remote Control Operating Instructions cseeeeeeeeeees 15 Installing the Remote Control Holder ulunan nhununununwswwununusuawa 15 Reverse Switch Operating Instructions cssssseeseeseeseeeeeees 16 Care and Cleaning 1111 11 7000700002auuaanamanananaaasasasasannnanan 16 Troubleshooting ku 17 Semice PANS cecadewctecvievesiasacsteanaaccessevasecsnaveasacantvensdecetae 18 Safety Information Read and save these instructions To reduce the risk of electric shock ensure electricity has been turned off at the circuit breaker or fuse box before beginning All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 1999 and local electrical codes Electrical installation should be performed by a qualified licensed electrician The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs Use only UL listed outlet boxes marked FOR FAN SUPPORT The fan must be mounted with a minimum of 7 ft clearance from the trailing edge of the blades to the floor Avoid placing objects in the path of the blades To avoid personal injury or damage to the fan and other items be cautious when working
15. y not be acceptable for fan support and may need to be replaced If in doubt consult a qualified electrician If your ceiling fan does not have an existing UL listed mounting box then install one using the following instructions Disconnect the power by removing the fuses or turning off the circuit breakers Secure the ceiling outlet box JJ not included directly to the building structure Use appropriate fasteners and materials not included The outlet box and its bracing must be able to fully support the weight of the moving fan at least 35 Ibs Do not use a plastic outlet box The illustrations below show two different ways to mount the outlet box JJ not included JJ To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar KK not included as shown above HAMPTONBAY COM Please contact 1 800 527 0998 for further assistance Assembly Hanging the Fan Attaching the mounting bracket 2 Hanging the fan motor assembly to the electrical box from the mounting plate Lift the fan into position by hanging the fan motor assembly B onto the hook from the ceiling mounting bracket A allowing it to hang freely WARNING To reduce the risk of fire electric shock or other personal injury mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the m
16. y the original purchaser We also warrant all other fan parts excluding any glass or acrylic blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident misuse improper installa tion or by affixing any accessories is not covered by this warranty Because of varying climatic conditions this warranty does not cover any changes in brass finish including rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered a defect Servicing performed by unauthorized persons shall render the warranty invalid There is no other express warranty We hereby disclaim any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty Some states d
Download Pdf Manuals
Related Search