Hampton Bay 70830 Instructions / Assembly
Contents
1. button will control the light brightness Hold the key down to increase or decrease the light Tap the key quickly to turn the light off or on If you press the button in excess of 0 7 seconds it becomes a dimmer The light varies cyclically in 0 8 seconds The light key has auto resume so it will stay at the same brightness as the last time it was turned off For fans that use Fluorescent or LED bulbs select ON in the frequency switches this button will control the light ON OFF only YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT 4 TROUBLESHOOTING GUIDE A Fails to operate a Power to the receiver b Receiver wired correctly c Fan manual speed control in highest position d Light kit switch turned on e Good battery in the transmitter f Code set at exact same position in both transmitter and receiver B Won t operate at distance If transmitter operates the fan and the light kit when up close but not a 30 feet away try placing the black antenna wire higher up through the ceiling outside the junction box NOTICE Your ceiling fan and light kit assembly must meet the following requirements 1 Do not use with solid state fans 2 Electrical rating 120V 60 Hz MAX motor amps 1 0 A MAX light watts 300 W Fig E Fig F If there are wires with different colors have this unit installed by a qualified electrician e Push all connected wires up into junction box f Reinstall the canopy on t2. IGHT Blue light wire Frequency switches Frequency switches Receiver Fig B Transmitter Fig A Fig C RECEIVER Fig D AC SUPPLY BLACK WHITE BARE GREEN WHITE WHITE BLUE BLUE BLACK BLACK RECEIVER NOTE When installing the remote control be sure your fan is set on HIGH SPEED and the light is ON ON NOTE Frequency Switches D Incandescent use Dimming ON CFL or LED use On Off only ON ECE 1 2 3 4 ON D ON ON ECE 1 2 3 4 ON D 3 OPERATING TRANSMITTER A Install 12V MN21 A23 battery included To prevent damage to transmitter remove the battery if not used for long periods Figure E B Store the transmitter away from excess heat or humidity C This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units such as garage door openers car alarm or security system If you find that your fan and light kit go on and off without using your remote control simply change the combination code in your transmitter and receiver D Operation buttons on the panel of the transmitter Figure F The HI MED LOW buttons These three buttons are used to set the fan speed as follows LOW Low speed MED Medium speed HI High speed The OFF button This button turns the fan off The button For fans that use incandescent bulbs select D in the frequency switches this
3. Model No 191 691 Vendor No 11289 UPC 792145354338 REMOTE CONTROL INSTALLATION GENERAL INFORMATION This remote control is designed to separately control your ceiling fan speed and light brightness The fan button will control the fan speed Hi Med Low Off Select D or ON in the frequency switches to control the light dimmer or ON OFF function based on your light bulbs The red indicator on the transmitter will light when the button is pressed INSTALLATION AND OPERATING INSTRUCTIONS NOTE This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units The frequency switches on your receiver and transmitter have been preset at the factory Please recheck to make sure the switches on transmitter and receiver are set to the same position any combination of settings will operate the fan as long as the transmitter and receiver are set to the same position 1 SETTING THE CODE This unit has 16 different code combinations To set the code perform these steps Caution The dip switches on the receiver unit are covered with a rubber cover remove the rubber cover and then place back after making any changes to the dip switches A Setting the code on the transmitter a Remove the battery cover Press firmly below the arrow and slide battery cover off b Slide the frequency switches to your choice of up or down position Factory setting is all up Do not use
4. he mounting bracket g Restore the electrical power Distributed by Home Depot U S A Inc 2455 Paces Ferry Rd N W Atlanta Georgia 30339 TOLL FREE 1 877 902 5588
5. this Position Use a small screwdriver or a ballpoint pen to slide firmly up or down Figure A c For use with incandescent bulbs use the D setting for full range dimming For fans that use Fluorescent or LED bulbs use the ON setting for the light to have ON OFF functions only d Replace the battery cover on the transmitter B Setting the code on the receiver a Slide the frequency switches to the same positions as set on your transmitter Figure B 2 INSTALLING RECEIVER IN THE CEILING FAN A Safety precautions WARNING HIGH VOLTAGE Household electrical power can cause serious injury or death Disconnect the source of electrical power to the ceiling fan by removing the fuse or switching off the circuit breaker B Installing receiver in fan a Remove the ceiling fan canopy from the mounting bracket b Disconnect the existing wiring between the ceiling fan and supply at the electrical junction box c Lay the black antenna wire on top of the receiver and put the receiver in the mounting bracket Fig C d Make the connections as follows using the wire nuts supplied Fig D CONNECT TO Green fan wire Bare supply wire Black receiver wire AC IN L Black supply wire White receiver wire AC IN N White supply wire White receiver wire TO MOTOR N White fan wire Black receiver wire TO MOTOR L Black fan wire Blue receiver wire FOR L
Download Pdf Manuals
Related Search