Hunter 59031 Installation Guide
Contents
1. 42813 01 s 11 27 13 Hunter Fan Company 3 Installing the Plane Decal Note Please follow the instructions carefully 3 1 Slide the Landing Gear decal and the to insure proper mounting of the decal Read Canopy Tail decal behind the ceiling plate a a HS SH 3 2 Align the decals with the ceiling plate and The decal comes complete with pressure sensitive with one wall for squareness tape and special clips to hold it to the ceiling The decal is in four parts the Landing Gear Canopy Tail and two Wings Be sure the insignia emblem is 3 3 Tighten the wood screws on the ceiling plate just enough to hold the decals in place mounted on top for the right wing and on bottom 3 4 Put two small pieces of tape or another for the left wing See Step 3 4 The ceiling should bonding application to temporaly secure the be clean and dry for proper adhesion of the tape decal to the ceiling under the corners of the strips Landing Gear decal Ceiling Plate Tape with Corners Marked Insignia Step 3 4 Hunter Fan Company 42813 01 11 27 13 42813 01 s 11 27 13 Wing Decal 2 Note Make sure the double sided tape and pressure sensative round tape is on the non printed side of the decal 3 5 Mark the tape to indicate the corners of the decal This is extremely important as it will give you the exact location for the decal Mark the positions of the wheels and the two wing joint lines Canopy Tail2. Mark Ceiling in These Locations For Each Wing Hide Marks Under Wing Wing Joint Landing Gear Line Decal Hunter Fan Company 3 Installing the Plane Decal Cont 3 6 Loosen the wood screws and remove the decals Meal A 3 7 Use a wood block to drive the metal disk into Disk CER the ceiling Wood Block m Note Metal Disk will leave a permanent marks in ope Hammer SS oy ceiling 3 8 Locate one metal disk between the two lines marked for each wheel and center one metal disk over each line marked where the wings join the Landing gear decal Step 3 7 3 9 Add the strips of the pressure sensitive rectangle tape to the back side of Canopy Tail decal Locate strips then peel off one side of the backing and press into place 3 10 Add a disk of pressure sensitive round tape to each of the 4 metal disk that have been driven into the ceiling Leave the peel off Pressure Sensitive Pressure Sensitive Round Tape Round Tape backing on the other side of the disks and strips until instructed to remove 3 11 Peel the backing from the strips on the Canopy Tail decal and from the disks under the wheels Do not remove the backing from the disks where the wings attach 3 12 Slide the Landing Gear decal back under the ceiling plate and align corners with lines marked on tape Press decal in place at wheels Step 3 9 3 13 Slide the Canopy Tail decal under the ceiling plate align with
3. the circuit breakers in the off position securely fasten a prominent 2 Installing the Ceiling Plate 5 warning device such as a tag to the service panel 3 Installing the Plane Decal 6 9 All wiring must be in accordance with national and local electrical 4 s Assembling and Hanging the Fan 10 codes and ANSI NFPA 70 If you are unfamiliar with wiring use a 5 e Wiring the Fan 11 qualified electrician 6 Installing the Motor Housing 12 e To reduce the risk of personal injury do not bend the blade E SEE e attachment system when installing balancing or cleaning the fan the Blades l iain 10012261 Never insert foreign objects between rotating fan blades 8 s Installation of Nosecone 14 To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls 9 s Operating and Cleaning YOUR Ceiling FAR lt sss sssase 15 10 Troubleshooting Guide 16 2013 Hunter Fan Company Hunter Fan Company 42813 01 11 27 13 Mounting and Optional Accessories Understanding Mounting Support Brace Hunter s patented mounting system provides you maximum ease in installing your fan This fan was designed to be mounted only on flat ceilings and can b
4. e Hammer wood block or a rubber mallet Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 42813 01 11 27 13 2 Installing of the Ceiling Plate A CAUTION Cover plate must be securely mounted as it supports the entire weight of the fan 2 _ Drill two pilot holes 9 64 diameter in the 2 x 4 brace at the outermost holes in the outlet box 2 2 Install the 3 Mounting Isolators into the top of the ceiling plate 2 3 Thread the wire leads through the center hole in the ceiling plate and attach the ceiling plate to the brace Use 2 10 x 3 wood screws and washers for mounting 2 4 Do not tighten screws at this time Leave a 1 2 gap between the ceiling plate and the ceiling for insertion of the airplane decal 2x4 Wood Brace Outlet A Pong Mounting Screws Isolator Flat Washer Mounting Isolator T L T 3 Wood Screw
5. the landing gear decal and press into place on the ceiling 3 14 Tighten wood screws securely Remove the two pieces of tape that mark the corners Hunter Fan Company 42813 01 11 27 13 3 15 Turn each wing over and mark the approximate dimensions on the back side of the decal 3 16 Hold each decal in place on the ceiling and mark the ceiling at each location shown in Canopy Tail Mark Ceiling in a Step 3 15 Use the marks on the back of the Wing Decal 2 Decal Locations For Each Wing n 9n Hide Marks Under Wing decals as a guide 3 17 Drive 2 metal disk into the ceiling for each wing using the marks just placed in the ceiling as a guide Peel off one side of the backing on the remaining disks and strips 3 18 Press the strips onto the decal and the disks onto the clips just driven into the ceiling See Step 3 15 3 19 Remove the remaining peel off backing from all strips and disks Lift the corner of the Landing Gear decal carefully and remove the backing from the two disks Step 3 15 where the wings join 3 20 Place each wing into position making sure you are aligned with the metal disk and press into place 3 21 After the decal has been installed on ceiling add two strips of black decal tape over the joint between the wing and body of the plane 42813 01 s 11 27 13 Hunter Fan Company 4 Assembling and Hanging the Fan 4 1 Before hanging motor from ceiling plate install
6. the three grommets into the holes in the motor bracket 4 2 To hang the motor from the ceiling plate insert the T end of the bracket into the large hole in the ceiling plate with the notch in it Insert and rotate so top of motor is towards center of ceiling plate Hunter Fan Company Grommet Motor Bracket Step 4 1 O Motor Ceiling TOP Bracket Plate Step 4 2 42813 01 11 27 13 5 Wiring the Fan 5 1 Be careful when wiring so that you do not hit the motor and let it turn or it could fall out of the large hole ro mo 5 2 Make sure the power is still off 5 3 Connect electrical supply leads to the leads from the motor using approved connectors 5 4 To connect the wires hold the bare metal leads together and place a wire nut over them then twist clockwise until tight For all these connections use the wire nuts provided ACAUTION Be sure no bare wire or wire strands are visible after making connections 5 5 Connect the black electrical supply lead to the Step 5 4 5 5 black motor lead the white supply lead to the white motor lead and the ground lead to the green lead 5 6 After making the wire connections the wires should be spread apart with the white and green wires on one side of the outlet box and the black wires on the other side of the box The splices should be turned upward and pushed carefully into the
7. For Your Records and Warranty Assistance For reference also attach your receipt or a copy of your receipt to the manual Owner s Guide and Installation Manual Model Name Model No Date Purchased Where Purchased SINCE 1886 Form 42813 01 AON SUA 2013 Hunter Fan Co Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e Read this entire manual carefully before beginning installation Save these instructions Use only Hunter replacement parts To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan Table of Contents disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock 1 s Getting Read y 4 S l i j
8. ature Screw Hex Nut O O si Wrench 42813 01 s 11 27 13 Hunter Fan Company 8 Installation of Nosecone 8 1 Hand screw nosecone into bracket on bottom of switch housing making sure chain comes out the bottom hole in the nosecone Hand tighten only A CAUTION Do not overtighten nosecone Overtighting may damage the cone Hunter Fan Company lt Step 8 1 Ta Nosecone 42813 01 11 27 13 9 Operating and Cleaning your Ceiling Fan 9 1 Turn on electrical power to the fan 9 2 The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector 9 3 Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft In warm weather use downward air flow pattern 9 4 For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust R
9. e used on ceilings less than 8 feet high Considering Optional Accessories Low Profile gt a eine Mounting Outlet Box Consider using Hunter s optional accessories including a wall Style mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and Me Ve optimum performance of your Hunter fan use only Hunter speed controls Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high 42813 01 s 11 27 13 Hunter Fan Company 1 Getting Ready Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped Hunter Fan Company To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site
10. emove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish 9 5 Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish In cold weather use upward air flow pattern To Change Aireflow Direction Turn the fan off and let it come to a complete stop Remove the nosecone Slide the revering switch on the fan to the opposite position Re Install nosecone restart fan Reversing Switch 42813 01 s 11 27 13 Hunter Fan Company 10 Troubleshooting Guide Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Check all connections according to the wiring the fan section 3 Push motor reversing switch firmly left or right to ensure that the switch is engaged 4 Pull the pull chain to ensure it is on Problem Noisy operation 1 Tighten the blade assembly screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron armature screws 3 Turn power off support fa
11. n very carefully and check that the motor bracket is properly seated If you need parts or service assistance please call 1 888 830 1326 or visit us online at http www HunterFan com Hunter Fan Company 7130 Goodlett Farms Pkwy Suite 400 Memphis Tennessee 38016 ee Hunter Fan Company 42813 01 s 11 27 13 2013 HUNTER FAN COMPANY 42813 01 s 11 27 13 Hunter Fan Company
12. outlet box 5 7 Complete hanging of the motor by rotating it upwards and mounting with 3 shoulder screws supplied Shoulder Screw Step 5 6 5 7 Shoulder Screw P 42813 01 s 11 27 13 Hunter Fan Company 6 Installing the Motor Housing 6 1 Install the motor housing to the ceiling plate using the 4 8 32 machined screws that are pre assembled into the side of the ceiling plate 8 32 Screw Motor Housing Step 6 1 8 32 x 1 2 Machine Screw Hunter Fan Company 42813 01 s 11 27 13 7 e Assembling the Blades 7 1 Assemble the blades to the blade iron ring using the blade asembly screw 7 2 Put the screws into the holes in the blade set 8 Gs the blade on the blade iron ring and mount with the nuts provided We have provided a i wrench to tighten the nuts 2 gt tron Blade Ring 7 3 Install the blade iron ring to the motor using i the blade Iron armature screws Step 7 1 g 7 4 Slide the ring with the blades attached over the switch housing rotating the ring until it clears the switch housing 7 5 Mount the ring to the motor hub with the four screws identified above lt I a Step 7 3 Blade Iron Armature Screw gt J Blade gt FANN Hex Nut Assembly Screw ON Z Blade lron i Arm
Download Pdf Manuals
Related Search