Hunter 59160 Installation Guide
Contents
1. 2015 Casablanca Fan Company Refer to CAUTION c 1 on pg 2 www CasablancaFanCo com 1 888 227 2178 For Standard Mount Position Lift the canopy or Low Profile Insert the two canopy screws the canopy so that when lifted canopy into place so that the found in the hardware bag into place the canopy fits into the screw holes are aligned hanging bracket as shown For Low Profile Skip this step M8526 01 04 16 15 2015 Casablanca Fan Company Blades Install the grommets found in the W hardware bag in the blades by hand Place each blade between a blade iron and medallion Install three blade screws found in the amp hardware bag to attach the medallion to the blade iron Repeat this process for each blade Lightly attach the blade irons to the motor assembly with screws found in the X hardware bag then securely tighten after all screws are attached M8526 01 04 16 15 2015 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Switch Housing amp Light Kit Screw two upper switch housing screws R from the hardware bag halfway into the mounting plate on the bottom of the motor housing It does not matter which two screw holes you choose Feed the wire plug through the center hole of the upper switch housing then wrap keyhole slots around the screws and twist counterclockwise M8526 01 04 16 15 2015 Casablanca Fan Company www Casabl2. LEL meym e aleyaie www CasablancaFanCo com 1 888 227 2178 Congratulations on purchasing your new What to Expect with Casablanca ceiling fan It will provide Your Installation comfort and performance in your home or office for many years This installation j and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Preparation To register your fan please visit www CasablancaFanCo com register Save your receipt for proof of purchase Operation Switch Housing amp Maintenance amp Blades Light Kit Cleaning M8526 01 04 16 15 2015 Casablanca Fan Company What to Expect with Your Installation Must be able to secure the fan to building structure or fan rated outlet box You may need a friend to help you Check box to see fan weight If you are unfamiliar with wiring use a qualified electrician D Know your wiring i Ceilings that are more than 34 will require an angled mounting kit See page 3 for details A Assess ceiling angle 30 inches from blade tip to nearest wall or obstruction 7 feet From bottom edge of blade to the floor A Assess location Standard Downrod for ceilings 8 10 feet high Shorter Downrod for fan
3. the motor Discard the screws Note Some fans will have a shipping ring instead of shipping blocks Please remove the ring and discard the screws M8526 01 04 16 15 2015 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 DO NOT install the blades before mounting the motor and making the wire connections Downrod www CasablancaFanCo com 1 888 227 2178 Standard skip to next page Downrod for ceilings 8 10 high If you need a different downrod length follow these steps Longer Steps 1 5 to remove standard downrod pipe Downrod for angled ceilings or ceilings 10 or higher For Standard Mount pre assembled For Standard Mount Shorter Downrod for fans installed close to ceiling lt u A gt l f O L Included Sold Separately Steps 6 10 to reassemble with new pipe M8526 01 04 16 15 2015 Casablanca Fan Company Downrod continued www CasablancaFanCo com 1 888 227 2178 T U N O O Remove the pre installed setscrew so that the downrod can be inserted Slide the adapter cover onto the The wires can be cut downrod for standard mount only but leave at least 8 then hand tighten the downrod at extending from the top least 4 5 full turns until it stops of the downrod Tighten the setscrew with pliers DO NOT HAND TIG
4. the notches in the outer rim Attach the LED assembly to the Pza to the lower switch housing by of the globe or no light cap so they switch housing by installing installing two light kit assembly line up with the tabs on the inside two light kit assembly screws screws found in the amp hardware rim of the upper switch housing found in the amp hardware bag bag Carefully lift the globe or no light through the slots not the screw cap up as far as it will go then rotate holes clockwise until it is held tightly in If installing the No Light Cap place by the tabs Skip this step M8526 01 04 16 15 2015 Casablanca Fan Company Remote Control Battery Door Phillips Head Screw To access the battery compartment remove the small Phillips head screw that secures the battery door to the transmitter assembly The battery should be installed with the positive side up Replace with a CR2032 battery when necessary www CasablancaFanCo com 1 888 227 2178 The remote transmitter is already paired to the receiver and ready to use Note If you would like to operate multiple fans or multiple remotes or if your remote is not working please see the Troubleshooting See next page for fan section at the end of this manual 5 4 operation instructions M8526 01 04 16 15 2015 Casablanca Fan Company Operation Maintenance amp Cleaning www Casa
5. wire connector over them then twist clockwise until tight adi s Mo aX uaa16 Place the receiver on top of the downrod assembly as shown Refer to CAUTION c 1 on pg 2 Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box M8526 01 04 16 15 2015 Casablanca Fan Company me r Wiring continued www CasablancaFanCo com 1 888 227 2178 Using the orange wire connectors Using the orange wire connectors from the remote control hardware bag from the hardware bag 4219 e Connect the yellow wire from e Connect the black ungrounded the receiver to the black wire wire from the ceiling to the black from the fan wire from the receiver Connect the blue wire from the Connect the white grounded receiver to the blue wire or wire from the ceiling to both the possibly black with white stripe white wire from the receiver and wire from the fan the white wire from the fan papunosbun papunosb ay4ym Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of l the outlet box and the ungrounded wires on the other side of the outlet box J M8526 01 04 16 15
6. HTEN If the setscrew is not tightened securely the fan may fall M8526 01 04 16 15 2015 Casablanca Fan Company Mounting Options For Standard Mount Put the wires and downrod through the canopy Let the canopy sit loosely on top of the fan For Low Profile Put the wires and downrod through the Low Profile canopy Let the canopy sit loosely on top of the fan Note You MUST use a shorter downrod if installing the low profile canopy See page 7 for details M8526 01 04 16 15 2015 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 SF mi DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES Once you have chosen and placed your canopy lift the fan assembly and insert the downrod ball into the slot in the ceiling bracket www CasablancaFanCo com 1 888 227 2178 Note If using the optional Low Profile canopy you may need to carefully tilt the fan assembly at an lt angle while connecting the wires Be sure to tilt the fan AWAY from Receiver the opening in the ceiling bracket E7 and ensure the fan does not fall Using an orange wire connector from the hardware bag Mo aX4 uUaas6 Connect the 3 grounding wires green green yellow stripe or bare copper coming from the ceiling downrod and ceiling bracket green yellow stripe Bulpunosb du s Note To connect the wires hold the bare metal leads together and place a
7. Use Angled Mounting BOTH Ceiling amp Wall or Low Profile Mounting to hang the fan from a You need ONLY to hang the fan from a flat ceiling vaulted or angled ceiling a Longer Downrod most common Mounting Kit M8526 01 04 16 15 2015 Casablanca Fan Company Ceiling Bracket 4 aa For angled ceilings point opening toward peak Make sure all four bumpers are still attached If you are unable to do this call Technical Support at 1 888 227 2178 Refer to warning w 1 on pg 2 Use wood screws included when securing to support structure with approved electrical outlet box Drill 9 64 pilot holes in support structure to aid in securing ceiling bracket with hardware found in the X hardware bag 5 www CasablancaFanCo com 1 888 227 2178 Use machine screws provided with outlet box when securing to existing ceiling fan rated outlet box Make sure it is securely installed and is acceptable for fan support of 31 8 kg 70 Ibs or less To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location M8526 01 04 16 15 2015 Casablanca Fan Company Preparation Time Saver Tip Get a helper to insert grommets found in the W hardware bag into the blades while you re doing the next couple of steps Remove the shipping blocks from
8. Within three minutes press and hold both the Fan Off button and the 4 button for four seconds to pair the remote If applicable the fan will turn on and the lights will flash and stay on to indicate successful pairing Unpairing Procedure for Faulty Operation of Remote Controls If a transmitter is mistakenly operating a fan you need to unpair the transmitter from that fan s receiver The unpairing procedure is the same as the pairing procedure Note To prevent faulty operation you MUST disconnect power at the wall switch breaker or fan from all other ceiling fans within range while unpairing a fan Disconnect power from all other fans while unpairing Then cycle power to the fan you wish to unpair by turning power off and back on at the wall switch or circuit breaker if necessary Within three minutes press and hold both the Fan Off button and the 4 button for four seconds to unpair the remote If applicable the fan will turn off and the lights will flash and turn off to indicate successful unpairing
9. ancaFanCo com 1 888 227 2178 Insert the third upper switch housing Pza screw found in the hardware bag into place and then tighten all three screws Make sure the upper switch housing is securely attached to the mounting plate Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling Switch Housing amp Light Kit continued If installing the LED light Slide the switch housing cap through the hole in the center of the LED assembly Remove the dummy terminals from the blue and white pin connectors in the switch housing Connect the pin connectors from the switch housing and the LED assembly If installing the No Light Cap Skip this step Connect the 9 pin plugs from the upper and lower switch housings Make sure to line up the colored markings on the connectors M8526 01 04 16 15 2015 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 C P N ee S 2 D cS gt ED H SSD Install the three lower switch housing screws found in the hardware bag into place and then tighten all three screws securely Make sure the lower switch housing is securely attached to the upper switch housing Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling i e Switch Housing amp Light Kit continued www CasablancaFanCo com EZA If installing the LED light Attach the switch housing cap Position
10. blancaFanCo com EZA Reverse Switch The Fan Off button found on the right side of The up arrow and down arrow buttons control the To change the direction of air flow move the the transmitter turns the fan off lights on the fan Quickly press and release the up reverse switch to the opposite position You Buttons 1 through 4 turn on the fan and or down arrow to turn the lights off and on Hold must remove the globe or no light cap in control the speed the up or down arrow to raise or dim the light level order to access the reverse switch Dimming Mode To enable dimming you must j first set your remote to Dimming Mode To toggle l Dimming Mode on or off hold down the Fan Off fe aeien button while pressing the Light Down arrow twice e 4 High M8526 01 04 16 15 2015 Casablanca Fan Company e 1 Extra Low e 2 Low Operation Maintenance amp Cleaning continued For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning products may damage the finishes Safe Exit The Safe Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out To use Safe Exit e Press the Fan Off button for at least three seconds to initiate the Safe Exit Mode e The lights will flash for visual confirmation e The lights will stay on 50 brightness for 15 seconds and then begin to dim After a total of 30 seconds the lights will b
11. e completely off Your Universal Remote comes with a wall plate that has two posts on which to mount your transmitter when not in use M8526 01 04 16 15 2015 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Casablanca fans have the power to cut your cooling costs up to 40 Beat the High Cost of Cooling The air movement created by a Casablanca ceiling fan lets you set your thermostat higher and still stay comfortable Every degree you raise the thermostat saves up to 7 on energy costs So you can cut back on expensive air conditioning and save up to 40 on cooling In winter your Casablanca fan recirculates warm air and saves up to 10 on heating bills On average at low speed settings Your savings may vary based on climate building type and thermostat setting Save Energy and Money While Protecting the Environment Congratulations You re saving energy and money while protecting the environment by purchasing this ENERGY STAR qualified Casablanca ceiling fan With this purchase you are doing your part to protect the environment Your new ceiling fan has earned the ENERGY STAR label because it meets high energy efficiency specifications set by the Environmental Protection Agency EPA ENERGY STAR labeled ceiling fans save energy because they have more efficient fan motors and air delivery due to more aerodynamic blade configurations Ceiling fan models bearing the ENERGY STAR label move ai
12. er to the fan by turning power off and back on at the wall switch or circuit breaker if necessary Within three minutes press and hold both the Fan Off button and the 4 button for four seconds to pair the remote If applicable the fan will turn on and the lights will flash and stay on to indicate successful pairing M8526 01 04 16 15 2015 Casablanca Fan Company AUTHORIZED SERVICE CENTERS For the most updated list of Casablanca Authorized Service Centers visit www CasablancaFanCo com or call toll free 1 888 227 2178 LED lights will not dim To enable dimming you must first set your remote to Dimming Mode To toggle Dimming Mode on or off hold down the Fan Off button while pressing the Light Down arrow twice Troubleshooting continued Installing Multiple Fans with Independently Operating Remote Controls y y To install multiple fans with independently operating remote controls there is no need to perform any pairing procedures Each set of receiver transmitter is already paired Simply install each receiver into a fan and use the appropriate transmitter to operate each fan If your remote is not working see the Remote does not work section on the previous page Installing Multiple Fans Operating on a Single Remote Control To have multiple fans operated by a single remote control y
13. ou must pair the transmitter to each additional receiver The receiver that shipped with your fan is already paired to the transmitter Note To prevent faulty operation you MUST disconnect power at the wall switch breaker or fan from all other ceiling fans within range while pairing each fan For each additional fan ensure that a compatible receiver is installed Disconnect power from all other fans while pairing To pair cycle power to the fan by turning power off and back on at the wall switch or circuit breaker if necessary Within three minutes press and hold both the Fan Off button and the 4 button for four seconds to pair the remote If applicable the fan will turn on and the lights will flash and stay on to indicate successful pairing M8526 01 04 16 15 2015 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Installing One Fan Operating on Multiple Remote Controls I To have multiple remote controls operate one fan you must pair each additional transmitter to the receiver in the fan The transmitter that shipped with your fan is already paired Note To prevent faulty operation please disconnect power at the wall switch breaker or fan from all other ceiling fans within range while pairing For each additional transmitter cycle power to the fan by turning power off and back on at the wall switch or circuit breaker if necessary
14. r 14 20 more efficiently than typical ceiling fan models For more information on ENERGY STAR visit www energystar gov www CasablancaFanCo com 1 888 227 2178 Troubleshooting Fan doesn t work Excessive wobbling Remote does not work e Press a fan speed button 1 4 e Tighten all of the blade and e Make sure the battery is installed Push the motor reversing switch firmly left or right to ensure that it is engaged Check the circuit breaker to ensure the power is turned on Make sure the remote control battery is working Make sure the blades spin freely Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on pages 10 11 Check the plug connections in the switch housing blade iron screws until they are snug Turn the power off support the fan carefully and check that the hanger ball is properly seated Use the provided balancing kit and instructions to balance the fan Noisy Operation e Tighten the blade and blade iron screws until they are snug e Check to see if any of the blades are cracked If so replace all of the blades correctly e Install a new battery If the remote still does not work you may need to pair your remote To prevent faulty operation please disconnect power at the wall switch breaker or fan from all other ceiling fans within range while pairing To pair cycle pow
15. s equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Tools Needed www CasablancaFanCo com 1 888 227 2178 amp e L Ladder L Pliers L Wire Strippers E Power Drill 9 64 Drill Bit optional optional If mounting to a support structure you will also need these tools 3 M8526 01 04 16 15 Rk 2015 Casablanca Fan Company ia ogo q a Ceiling Options www CasablancaFanCo com 1 888 227 2178 4 e ka ea ra ka ea a a e o N ea ra o o l OQ i egoe U p If you have a flat ceiling Hang your fan by a standard downrod included Standard Support Support Mounting Structure Tae e If you have an angled ceiling SAN D 1 You will need a longer downrod sold separately a 2 If your ceiling angle is greater than 34 you will Angled 2 required also need an Angled Mounting Kit sold separately Mounting N Outlet Box required Mounting Use the three steps below to determine if your ceiling angle is greater than 34 Use Standard Mounting
16. s installed close to ceiling EJ Longer Downrod for ceilings 10 feet or higher LA Select a downrod length 2 M8526 01 04 16 15 2015 Casablanca Fan Company www CasablancaFanCo com 1 888 227 2178 Read and Save These Instructions This product conforms to UL Standard 507 A WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Casablanca Solid State Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Casablanca replacement parts Thi
Download Pdf Manuals
Related Search