Global Direct 21094 Installation Guide
Contents
1. 21097 21094 CSA010011HAUT 1 INSTALLATION INSTRUCTIONS PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS AS YOU MAY NEED THEM AT ALATER DATE CAUTION Turn off the main power at the circuit breaker before installing the fixture in order to prevent possible shock Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions FOR CEILING MOUNT Fig 4 amp 5 1 A Place the 8 32 HEX NUTS 3 onto the 8 32 FIXTRUE MOUNTING SCREWS 4 and attach the FIXTURE MOUNTING SCREWS to the MOUNTING BRACKET 2 or universal mounting plate whichever is provided Do not tighten the HEX NUTS at this time Fig 4 B If the fixture uses a single 1 8 IPS NIPPLE 4 for mounting thread the 1 8 IPS HEX NUT 3 onto the NIPPLE and screw the NIPPLE into the MOUNTING BRACKET 2 without tightening the HEX NUT Fig 5 2 Pull the power supply wires out from the OUTLET BOX 1 and mount the MOUNTING BRACKET 2 or the universal mounting plate to the OUTLET BOX using MOUNTING SCREWS 10 3 Attach the power supply wires to the fixture lead wires by connecting BLACK to BLACK or SMOOTH and WHITE to WHITE or RIBBED Attach the POWER SUPPLY GROUND WIRE 7 from the OUTLET BOX 1 and the FIXTURE GROUND WIRE 8 from the fixture to the green GROUND SCREW 9 on the MOUNTING BRACKET 2 or connect both w2. OLLAR LOOP is centered with the center hole opening of the CANOPY Take away the CANOPY and tighten the HEX NUTS down on the MOUNTING BRACKET 2 and the SCREW COLLAR LOOP 3 Open up the end links of the CHAIN 17 and attach one end of the CHAIN onto the FIXTURE LOOP 18 Slide the THREADED RING 16 from the SCREW COLLAR LOOP 6 and the CANOPY 15 onto the CHAIN in that order and attach the other end of the LOUTLET BOX 2 MOUNTING BRACKET 3 8 32 HEX NUT 4 FIXTURE MOUNTING SCREW 5 WHITE TO WHITE WIRE CONNECTION 6 BLACK TO BLACK WIRE CONNECTION 7 POWER SUPPLY GROUND WIRE 8 FIXTURE GROUND WIRE 9 GROUND SCREW 10 MOUNTIN SCREW 11 CANOPY 12 DECORATIVE NUT LOUTLET BOX 2 MOUNTING BRACKET 3 1 8 IPS HEX NUT 4 NIPPLE 5 WHITE TO WHITE WIRE CONNECTION 6 BLACK TO BLACK WIRE CONNECTION 7 POWER SUPPLY GROUND WIRE 8 FIXTURE GROUND WIRE 9 GROUND SCREW 10 MOUNTIN SCREW 11 CANOPY 12 DECORATIVE NUT 1 US f ANNAN AAV CHAIN on to the SCREW COLLAR LOOP Close the ends of the chain links 4 Unravel the fixture s lead and ground wires and thread the lead and ground wires through i T i Nena every other link of the CHAIN 17 and out through the SCREW COLLAR LOOP 6 and NIPPLE 4 assembly starting with the chain link attached to the FIXTURE S LOOP 18 5 Attach the power supply wires to the fixture lead wires by connecting the BLACK POWER SUPPLY WIRE 11 to the SMOOTH FIXTURE LEAD WIRE 12 an
3. d the WHITE POWER SUPPLY WIRE 9 to the RIBBED FIXTURE LEAD WIRE 10 Attach the SUPPLY GROUND WIRE 8 from the OUTLET BOX 1 and the FIXTURE GROUND WIRE 7 from the fixture onto the green GROUND SCREW 14 on the MOUNTING BRACKET 2 or connect both wires together using the correct size of WIRE CONNECTORS 13 Place connected wires inside of the OUTLET BOX 6 Slide the CANOPY 15 and the THREADED RING 16 of the SCREW COLLAR LOOP 6 up the CHAIN 17 Place the CANOPY over the OUTLET BOX 1 and secure in place by screwing the THREADED RING onto the SCREW COLLAR LOOP 7 Screw in light bulbs that do not exceed the maximum wattage specified on the fixture s wattage rating label into the socket s on the fixture NOTE If the bottom opening of the lamp compartment to the fixture is too narrow to allow access to the light bulb s unscrew the two decorative screws at the top of the lamp compartment to allow it to drop down for lamp replacement INSTALLATION COMPLETED CST001 7 IT EI I Lies 1 LOUTLET BOX 2 MOUNTING BRACKET 3 MOUNTING SCREW 4 NIPPLE 5 1 8 IPS HEX NUT 6 SCREW COLLAR LOOP 7 FIXTURE GROUND WIRE 8 SUPPLY GROUND WIRE 9 WHITE SUPPLY WIRE 10 RIBBED FIXTURE LEAD WIRE 11 BLACK SUPPLY WIRE 12 5MOOTH FIXTURE LEAD WIRE 13 WIRE CONNECTOR 14 GROUND SCREW 15 CANOPY 16 THREADED RING 17 C HAIN 18 FIXTURE LOOP 11 12
4. ires together using the correct size of wire connectors 4 Place the CANOPY 11 on the fixture over the OUTLET BOX 1 and onto the fixture mounting screws or NIPPLE 4 and adjust the 8 32 fixture mounting screws or NIPPLE until they protrude out from the CANOPY 1 4 Remove the CANOPY and secure the position of the fixture mounting screws or NIPPLE by tightening the HEX NUT S 3 against the MOUNTING BRACKET 2 Place the CANOPY back onto the fixture mounting screws or NIPPLE and secure into place using the DECORATIVE NUTS 12 provided 5 Screw in light bulbs that do not exceed the maximum wattage specified on the fixture s wattage rating label into the socket s on the fixture INSTALLATION COMPLETED FOR CHAIN SUSPENDED CEILING MOUNT Fig 6 1 Screw the 1 8 IPS HEX NUTS 5 onto the 1 8 IPS NIPPLE 4 and then attach the end of the NIPPLE that has the HEX NUT to the MOUNTING BRACKET 2 Do not tighten the HEX NUT Pull the SUPPLY GROUND WIRES 8 out from the OUTLET BOX 1 and attach the MOUNTING BRACKET 2 assembly to the OUTLET BOX by using the slotted holes on the MOUNTING BRACKET and the MOUNTING SCREWS 3 provided 2 Thread a 1 8 IPS HEX NUT 5 and the SCREW COLLAR LOOP 6 onto the NIPPLE 4 end that is facing down but do not tighten the HEX NUT Place the CANOPY 15 over the OUTLET BOX 1 and adjust the SCREW COLLAR LOOP and NIPPLE until the outside threads on the SCREW C
Download Pdf Manuals
Related Search