Hunter 53066 Instructions / Assembly
Contents
1. installation and Operation manual for Hunter For Your Records and Warranty Assistance Model Name Ceiling Fans Catalog Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a TY P E 2 AYA O d e S copy of your receipt to the manual 42508 01 05 03 07 Table of Contents 1 e Getting Ready 2 Installing the Ceiling Plate 3 e Assembling the Fan 4 Hanging and Wiring the Fan 5 Installing the Canopy and Canopy Trim Ring 6 Assembling the Blades 7 Completing Your Installation With or Without a Light Fixture 8 Operating and Cleaning Your Ceiling Fan 9 e Troubleshooting 2007 Hunter Fan Company Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts e To reduce2. Fan Steps 3 1 3 2 A WARNING Fan may fall if not assembled as directed in these installation instructions lt lt Downrod You can assemble your fan for standard or angle mounting as shown in steps 3 1 3 4 For low profile mounting ceilings less than 8 feet lt Canopy _ high go to steps 3 5 3 11 on the next page For Standard or Angled Mounting 3 1 Unbundle the wires from the fan Canopy Trim Ring 3 2 To assemble fan to hang down from a flat or angled ceiling insert a Setren the downrod through the canopy and canopy trim ring Feed the wires from the fan through the downrod 3 3 Loosen the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the set screw with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod Loop 3 4 Raise the fan and place the hook on the downrod through the loop on the ceiling plate The arrows on the downrod and on the Downrod af wee ti Hook ceiling plate should both be pointing towards the tab hole on the Step 3 4 ee canopy Go to 4 e Wiring the Fan 6 42508 01 05 03 07 Hunter Fan Company 3 e Assembling and Hanging
3. connect the black and the black white wire from the fan to the black wire in the ceiling A CAUTION Be sure no bare wire or wire strands are visible after making connections 4 5 Push all wires and wire nuts back through the ceiling plate hole into the outlet box Wire Nut 8 42508 01 05 03 07 Hunter Fan Company 5 Installing the Canopy and Canopy Trim Ring Note Be sure the arrows on the downrod and on the ceiling plate are Step 5 1 both pointing towards the tab hole on the canopy an a 5 1 Hook the tab hole in the canopy over the tab on the ceiling plate 5 2 Raise the canopy Make sure the holes in the canopy and in the pe Canopy ceiling plate are aligned Tab Hole 5 3 Partially install the three canopy screws into the canopy one at a time Once all three screws are in tighten them 5 4 Using both hands push the canopy trim ring up to the top of the canopy The canopy trim ring will snap and lock into place Canopy Trim Ring Should you need to remove the canopy trim ring follow these steps 1 Locate the tab indicators small bumps on top of tabs 2 Press firmly on opposite sides of the ring towards the canopy The tabs will flex out releasing the trim ring from the canopy Screw Step 5 4 9 42508 01 05 03 07 Hunter Fan Company 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the
4. flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angle mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance A CAUTION To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied Low Profile at Mounting Style Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high 3 42508 01 05 03 07 Hunter Fan Company Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill hole
5. the Fan Low Profile Only A WARNING Fan may fall if not assembled as directed in these installation instructions You can assemble your fan for standard or angle mounting as shown in steps 3 1 3 4 on the previous page For low profile mounting ceilings less than 8 feet high see steps 3 5 3 11 on this page For Low Profile Mounting Note For low profile mounting the downrod is replaced with the low profile washer 3 5 3 6 3 7 3 8 Raise the fan and place the hook on the adapter through the Unbundle the wires from the fan Remove the screw from the hanger ball on the downrod and then remove the hook from the hanger ball A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod Remove the set screw from the adapter Install the hook and two neoprene washers onto the adapter using the set screw the top of the hook must hang over the Step 3 6 r adapter Note The screw should be tight but still allow the hook Ip to rotate slightly Place the low profile washer lip up into the canopy Be sure the green ground wire is pointing up toward the ceiling Align the holes in the washer with the holes in the adapter Assemble securely with three low profile screws loop on the ceiling plate Low Profile Screw Zk Loop XS Downr
6. arning device such as a tag to the service panel 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter 2 2 Your fan comes with four neoprene noise isolators Isolators Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate 2 3 Thread the lead wires from the outlet box down through the hole in the middle of the ceiling plate 2 4 Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling 2 5 Place a flat washer on each of the two 3 wood screws and pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Wood Screw ements FEESUUNUETEDEUUNUUE be 5 42508 01 05 03 07 Hunter Fan Company lsolator _ P Step 2 2 Lod gt gt l l Steps 2 3 2 5 For Angled Ceilings Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing towards the ceiling peak 3 Assembling and Hanging the
7. e upper plug connector through the center opening of the housing Align the keyhole slots in the housing with the housing assembly screws Steps 7 1 7 3 Housing Turn the housing counterclockwise until the housing assembly Assembly o screws are firmly situated in the narrow end of the keyhole slots Screw ae r Install the remaining housing assembly screw into the housing Tighten all three screws firmly A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing and light fixture falling If you want to install the light fixture proceed with step 7 6 now If you do not want to install the light fixture you need to uninstall it now See Uninstalling the Light Fixture on page 12 Once you have uninstalled the light fixture continue with step 7 6 l1 42508 01 05 03 07 Hunter Fan Company 7 6 Plug Connector 7 7 Steps 7 6 7 7 Lower Switch Housing Plug T Connector 7 8 Detail 7 9 Housing 5 10 Assembly Screw Steps 7 8 7 10 7 e Completing Your Installation With or Without a Light Fixture continued To attach the lower switch housing connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will onl
8. fan Step 6 1 Detail 6 1 Your fan may include blade grommets If your fan has grommets insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 Some blade mounting screws are installed in the motor to secure shipping blocks Remove the blade mounting screws and rubber bumpers from the motor Save the screws and discard the bumpers 6 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade Blade Assembly mounting screw then securely tighten both mounting screws Screws Steps 6 1 6 2 Use without grommet Blade Mounting Screw 42508 01 05 03 07 Hunter Fan Company Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button This feature gives you the option of installing the fan with OR without the included light fixture The steps below direct you whether or not you are installing a light fixture A WARNING Use only the light fixture supplied with this fan model 7 1 7 2 7 3 7 4 7 5 7 Completing Your Installation With or Without a Light Fixture To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate Feed th
9. od with Hook Step 3 11 7 42508 01 05 03 07 Hunter Fan Company Low Profile Washer 4 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location 4 2 Decide how you want to set up the fan and light controls You can control the fan and or lights together or separately using one or two wall switches Follow Step 4 3 OR Step 4 4 depending on what you decide Note To connect the wires hold the bare metal leads together and place a wire nut over them then twist clockwise until tight 4 3 If you want to you can control the fan and light separately using two wall switches connect the wires as follows connect the green ground wire to the ground wire connect white wire to white wire connect black wire to black wire and connect the black white wire from the fan to the wire for the wall switch 4 4 Alternatively you can control both fan and light with one switch To do so connect the wires as follows connect the green ground wire to the ground wire connect white wire to white wire
10. s for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 42508 01 05 03 07 Hunter Fan Company 2 Installing the Ceiling Plate A CAUTION To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent w
11. s the fan finish Reversing Switch 14 42508 01 05 03 07 Hunter Fan Company 9 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Check to see if the blade is cracked If so replace all the blades 3 Be sure that the glass shades are secure 4 Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade and or blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 15 42508 01 05 03 07 Hunter Fan Company
12. te stop Slide the reversing switch on the fan to the opposite position Restart fan Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector The light pull chain controls power to the light The pull chain has two settings On and Off Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In cold weather having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner a
13. the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls 2 42508 01 05 03 07 Hunter Fan Company Installer s Choice and Optional Accessories Support Brace Ceiling Standard Outlet Box Mounting gt Style Standard Mounting hangs from the ceiling by a downrod included Mounting Angle Mounting recommended for a vaulted or angled ceiling Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation
14. ull chain switch from the light fixture housing 4 Locate and carefully remove the two capacitors 5 In the light fixture housing there are the following plug connectors one multi wire connector and two two wire connectors Unplug the two wire connectors one connector will have a black with white striped wire and a white wire coming from the multi wire connector 6 You have now disconnected the wiring harness and its components and are ready to install them into the empty switch housing The light switch remains in the light assembly housing 7 Insert the pull chain and fan pull chain switch through the round opening on the side of the empty switch housing Thread the bellmouth nut over the pull chain and hand tighten the bellmouth nut 8 Reattach the breakaway connector to the pull chain 9 Insert the reversing switch into the square hole on the side of the switch housing Install and tighten the two screws you removed previously from the other switch housing 10 Carefully place the capacitors in the switch housing 11 Continue with Step 7 6 on page 11 13 Bellmouth Nuts Steps 7 11 Switch Housing Fan Speed _ Switch 42508 01 05 03 07 Hunter Fan Company 8 Operating and Cleaning Your Ceiling Fan In warm weather use downward air flow pattern 8 5 In cold weather use upward air flow pattern To Change Airflow Direction Turn the fan off and let it come to a comple
15. y fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three housing assembly screws If you are not installing the light fixture your installation is complete Otherwise proceed with step 7 8 To install each shade first loosen the three thumbscrews Raise the shade to the light fixture Tighten the thumbscrews securely Install four A 19 light bulbs 60 Watt maximum each 12 42508 01 05 03 07 Hunter Fan Company Uninstalling the Light Fixture Steps 1 6 5 7 Light 1 You must remove the wiring harness and its Reversing Fj Assembly wth iin Housing components from the integrated light fixture You must then install the wiring harness into the empty switch housing included with the fan 2 Locate the reversing switch and carefully remove the Capacitors two screws holding the reversing switch to the lower s it sia Light switch housing Now remove the reversing switch Switch a Switch from the housing 3 Remove the patented breakaway connector from amp the end of the fan pull chain Carefully loosen the bellmouth nut from the pull chain and remove the p
Download Pdf Manuals
Related Search