Hunter 27189 Use and Care Manual
Contents
1. before installation The light level should only be changed by the Original control Receiver Installation 1 Disconnect power to the ceiling fan and light kit at the main electric panel Remove fuse or move circuit breaker to the OFF position 2 IMPORTANT Before installing this control change the factory default dip switch settings to your own unique code Refer to Figure 2 Be sure the dip switch positions of the transmitter and receiver match or the ceiling fan will not function Select different combinations of dip switches to prevent mis operation due Figure 1 Confirm Reverse gt Switch Figure 2 Dip Switch DOA zi T COs Transmitter Back ON DIP H Receiver Dip Switch Select your own unique code being sure settings match in the transmitter and receiver to other remote control fans garage door openers etc 3 This Original remote control mounts between the ceiling and fan hanger bracket Therefore if the fan is already installed it will need to be taken down 4 Wire the power leads coming from the ceiling outlet box Connect the main wires from the top of the control white to white and black to black See Figure 3 Push the wires up into the outlet box and arrange the wire connectors to point upward Separate the wires so that the black wires are on one side of the box and the white wires are on the other 5 Bring the control up to the ceiling F2. Original Remote Fan amp Light Control Model 27189 Ratings 120 VAC 60 Hz 2 0 Amp Fan 300 Watt incandescent light Receiver Weight 16 oz Read and Save these Instructions Caution Risk of Electrical Shock All wiring must be performed in accordance with national and local electrical codes If you are unfamiliar with the wiring codes you should use a qualified electrician To avoid overheating and possible damage to other equip ment do not install to control a receptacle fluorescent light fixture motor operated appliance or transformer supplied appliance Use only to control one paddle blade ceiling fan and incandescent light fixture Notes 1 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instructions may cause harmful interference to radio com munications However there is no guarantee that interference will not occ
3. at maximum brightness 3 Fan Operation Press the High Medium or Low speed buttons to turn the ceiling fan ON at the desired speed e Press the fan OFF key to turn the ceiling fan OFF For best fan operation Allow the ceiling fan motor to start on High then select the desired speed 4 Manual Light Switch Operation To turn the lights ON without battery power to the wall control turn OFF the wall switch for 5 seconds then turn the master switch back ON The light will turn ON at maximum brightness and the fan will be OFF 5 For everyday operation leave the master switch ON However if the control will not be used for an extended period of time 5 days or more turn the master switch OFF For more information on Hunter Fan products visit our website www hunterfan com Troubleshooting Symptom Possible Causes 1 No functions operate Main Power not restored Solution Replace fuse Turn ON circuit breaker Turn ON wall switch Fan pull chain not set to High Turn OFF power at wall switch or main electric panel Set fan to High speed Light pull chain not set to ON Set light kit to ON Receiver wiring incorrect Verify wiring connections Transmitter and receiver dip switches do not match Set transmitter and receiver to same dip switch setting Battery too weak 2 Operates only at close range Cable or power lines in ceiling run over fan Replace with new alkaline battery R
4. e orient any cables or wires Battery too weak 3 Inconsistent operation Signal partially blocked from reaching receiver Replace with new alkaline battery Extend antenna into ceiling box or move it for better reception RF interference Turn OFF wall switch for 5 seconds then turn back ON Continuing RF interference Change dip switch settings to a different code in both Transmitter and Receiver HUNTER FAN COMPANY ORIGINAL CONTROL LIMITED WARRANTY The Hunter Fan Company makes the following limited warranty to the original purchaser of the Original Control Control Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL THIS WARRANTY AND ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE VOIDED THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES THE DURATION OF ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN RESPECT TO ANY CONTROL IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL This warranty excludes malfunctions or failures which w
5. eed the bare copper ground wire down through the center hole of the control Use the lag screws includ ed to hold the control and and the fan mounting bracket in place See Figure 4 6 Mount the fan to the fan hanger Connect the white wire from the con trol to the fan white wire and the black wire to the black Connect the bare copper wire to the green ground wire from the fan Connect the red wire from the control to the fan through wire that goes directly to the light kit See Figure 5 Push the connections up through the center hole into the ceiling outlet box 7 Complete the installation of the fan by following the instructions sup plied with the fan 8 Restore power at main electrical panel Wall Control Installation 1 Remove rocker style wallplate not included to expose the wall wiring Disconnect the existing switch and remove from the electrical box 2 If 4 wires are visible connect each black wire to an Original control black black wire If 2 wires are visible connect each to an Original Figure 3 Electric Cable cS Y SS A La d eA Bare Copper Ground Wire Control Wooden Building Structure X Control Use Long Lag Screws Supplied Originale Fan with Control Bracket Bare Copper Wire Mount Directly to Structure Figure 5 Receiver Bare Ground 7 Copper from pnie Outlet Box eutral Through Lead for Light Kit Wiring Diagram control lead Use 2 of the large wi
6. ere caused by repairs by persons not authorized by us mishandling improper installation modifica tions or damage to the Control while in your possession or unreasonable use This warranty does not apply to batteries or to deterioration or damage to the product caused by the use of faulty batteries To obtain a replacement return your Control postage prepaid along with proof of purchase to Hunter Fan Company Service Department at 2500 Frisco Avenue Memphis Tennessee 38114 IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE 1999 Hunter Fan Company Form 41443 12 99
7. re nuts supplied to make the connec tions Refer to Figure 4 3 If a ground wire is provided in your electrical box attach it to the ground screw near the bottom of the mounting plate 4 Gently push wires and wall control into the electrical box Attach the Original control to the switch box with the two screws provided 5 Verify that the master switch is in the OFF Position Press inward on each side of the wall control to remove face cover Set the dip switches to match the dip switches in the receiver Install a 12 volt battery A23 MN21 or equivalent Replace the face cover Operation 1 Slide the master switch to the ON position After a 1 5 second delay the light will turn ON at maximum brightness 2 Light Operation Press and quickly release the light button on the wall mounted control to turn the light OFF or ON Light will come ON at maximum brightness e Press and hold the light button for more than 1 second to turn the light ON and decrease from maximum brightness to OFF e Release the light button when the desired light level is reached Figure 6 Light Button Fan Low Speed Fan Medium Speed Fan High Speed Master ON OFF e Continue to hold the light button to repeat the cycle Maximum light level decrease OFF While the light is ON holding the light button will decrease the light brightness e Turning the light OFF resets the dimming function The next press of the light button will start
8. ur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 3 For use only with electrically reversible ceiling fans rated at 2 0 amps or less and fan incandescent light kits rated at 300 watts or less 4 Not for use with shaded pole or non reversible motors 5 Medium and Low fan speeds are determined by the Original control and thus may vary from the factory settings due to normal motor variations Before Installing the Original Control 1 Confirm that your Hunter Original ceiling fan is electrically reversible Look for a reversing switch on the switch housing below the motor Refer to Figure 1 2 Use the pull chain switch to set the fan speed to the HIGH position before installation Do not use the pull chain to change the fan speed after installation as damage to your ceiling fan or control may result The speed of the fan should only be changed by the Original control 3 Set the ceiling fan light kit to the ON position
Download Pdf Manuals
Related Search