Sea Gull Lighting 4411-185 Installation Guide
Contents
1. E GROUND WIRE WIRE CONNECTOR UNIVERSAL MOUNTING GREEN BAR D GROUNDING FIGURE 2 SCREW G NOT SUPPLIED INSTALLATION HC 532 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Insert fixture mounting screws B into threaded holes of universal mounting bar A Run fixture mounting screws B all the way down to the heads STEP 2 Place universal mounting bar A against outlet box not supplied and secure in place using outlet box screws not supplied Be sure the mounting screws are perfectly vertical so fixture hangs straight A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK Oo HOUSEWIRE _ _ __ BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the2. paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
3. Installation And Safety Instructions HC 532 Saq Gull Lighting Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM ___ 103007 IMPORTANT SAFETY INSTRUCTIONS BEFORE YOU BEGIN e Be sure the electricity to the system you are working on is turned Carefully remove the fixture from the carton and check that all parts off either the fuse removed or the circuit breaker set at off are included as shown in figure 1 and 2 Be careful not to misplace e Use of other manufacturers components will void warranty listing any of the screws or parts which are needed to install this fixture and create a potential safety hazard e If you are unclear as to how to proceed contact a qualified electrician e You don t need special tools to install this fixture e Be sure to follow the steps in the order given e Read instructions carefully e Proper wiring is essential for the safe operation of this fixture e To reduce the risk of fire electric shock or personal injury mount to outlet box or supporting system able to support the weight of the fixture e Save these instructions SHADES E CANOPY C RETAINING RING F FIXTURE CAP SHADE ARM D NUTS G DECORATIVE I FIGURE 1 NOT INCLUDED GROUNDING amp UNIVERSAL MOUNTING BAR LOCK UP OUTLET BOX SCREWS MOUNTING OUTLET BOX SENS
4. connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw G is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture K and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw G on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire from the fixture K and the outlet box to it using a small wire connector not supplied NEVER CONNECT GR OUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY STEP 1 Make sure no bare wires can be seen outside wire connectors After wires are connected tuck them carefully inside the outlet box Position canopy C over mounting screws B and secure in place by threading cap nuts G onto fixture mounting screws B STEP 2 Remove rubber washer from socket Place shade E over socket Place rubber washer over socket and secure by threading retaining ring F onto socket Install lamps Attach shade decorative 1 to shade E CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive
Download Pdf Manuals
Related Search