Sea Gull Lighting 41035-962 Installation Guide
Contents
1. NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box Do Not twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw L is to be inserted into the hole with two raised dimples provided on the universal mounting bar J Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw L on the universal mounting bar J If uninsulated ground wire is on the universal mounting bar connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied See Figure 2 NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all2. U L specifications The listing mark of underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside the outlet box Position backplate M over mounting screws I and secure in place with cap nuts N STEP 2 Install glass B Secure in place with retaining ring C STEP 3 Install lamp
3. Na Installation And Safety Instructions HC 371 H H Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to sea gull lighting this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM 050698 IMPORTANT SAFETY INSTRUCTIONS CLEANING e Be sure the electricity to the system you are working on is turned To clean wipe fixture with a soft cloth Clean glass with a mild soap off either the fuse removed or the circuit breaker set Do not use abrasive materials such as scouring pads or powders at off steel wool or abrasive paper e Use of other manufacturers components will void warranty listing and create a potential safety hazard e If you are unclear as to how to proceed consult a qualified ORDERING PARTS electrician e Under no circumstances should a fixture be hung on house Keep this sheet for future reference and in case you need to order electrical wires nor should a swag type fixture be installed on a replacement parts Parts for this fixture can be ordered from place of ceiling which contains a radiant type heating system purchase Be sure to use exact wording from illustration when e You don t need special tools to install this fixture ordering parts e Be sure to follow the steps in the order given e Read instructions carefully e Proper wiring is essential for the safe operation of this fixture e Save these instructions Carefully remo
4. ve the fixture from the carton and check that all parts are included as shown in figure 1 Be careful not to misplace any of the screws or parts which are needed to install this fixture GROUNDING amp UNIVERSAL eines MOUNTING BAR LOCK UP FIG 2 RETAINING UNIVERSAL RING C MOUNTING GREEN GROUNDING OUTLET BOX PRAIS SCREW L SCREWS GLASS B OUTLET BOX MOUNTING SCREWS I any aN WIRE CONNECTOR UNIVERSAL MOUNTING PLATE J FIG 2 FIG 1 NOT SUPPLIED NOT SUPPLIED INSTALLATION HC 371 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Insert fixture mounting screws I in threaded holes of universal mounting bar J Run screws all the way down to the heads STEP 2 Place universal mounting bar J against outlet box not suppplied and screw in place using outlet box screws not supplied Be sure the mounting screws are perfectly horizontal so fixture hangs straight STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE l HOUSE WIRE HOUSE WIRE WHITE PARALLEL WIRE SQUARE amp RIDGED BLACK PARALLEL WIRE ROUND amp SMOOTH TN O WHITE OR GREY WITH TRACER NNN NYS BROWN GOLD OR BLACK WITHOUT TRACER WHITE OR GREY WITHOUT TRACER BROWN GOLD OR BLACK WITH TRACER Dn ee
Download Pdf Manuals
Related Search