AireRyder LK55616BBZ-C Use and Care Manual
Contents
1. and discard it 3 Attach nipple a of the light kit to the Pull Chain switch box cover then secure it with a washer and hex nut N Bulb Type A15 Max 60W 4 Pull out the wires from the switch box a Make wire connections using the wire nuts The smooth marked wire from the fixture to the black or blue wire from the switch box The ridged unmarked wire from the fixture to the white wire from the switch box Carefully put the wires back into the switch box 5 Attach the switch box cover back to the switch box using the three switch box screws 6 Carefully place the decorations onto the glass shades Then attach the glass shades to the glass holders and secure them with the set screws 7 Install bulbs included See relamping label at socket area or packaging for maximum allowed wattage 8 Turn on the power at the main fuse or circuit breaker box You can control the light with the pull chain aireRyder Page 1 2 091230 For Mini Chandelier See Fig 1 amp Fig 2 1 Take out the loop grounding pad and washer from Loop the hardware package for Mini Chandelier N 2 Adjust the hex nut on nipple a to make a length of 1 2 from the top of nipple a to the top of the hex Grounding Pad E Washer nut See Fig 1 3 Attach a washer and the grounding pad to the hex Nipple a nut on nipple a then secure them with the loop 3 nu 4 Choose the length of t2. ASSEMBLY AND INSTALLATION INSTRUCTIONS LK55416 LK55516 LK55616 LK55716 WARNING BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE NOTE 1 Before installing consult local electrical codes for wiring and grounding requirements 2 The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless additional support is provided for the fan WARNING As per EPACT 2005 requirements this fan light has a built in current limiting device to conserve energy Please do not operate it with lamps that together consume more than 190 watts If the Motor Switch Box Black or Blue Wire lt Wire Nut Smooth Wire fan light shut off shortly after it was switched on it may be due to excessive current demand Turn off power to the fan and replace the light bulbs with lower wattage bulbs Powers up again by pull chain or wall switch or remote control depend on what is installed with the particular fan White Wire Ridged Wire gt gt Hex Nut amp Washer ax Switch Box Screw Center Plug 8 aE Cover Fixture Arm For Light Kit ince Haider 1 Remove the switch box cover from ie the switch box of the fan by loosing Gase Shade the three switch box screws AB Decoration 2 Unscrew the center plug from the i Z switch box cover
3. he chain you need then ZI weave the fixture wire and the fixture grounding Fig 1 wire through the chain Then connect one end of the chain with the loop by using one loop lock 5 Secure the top loop to nipple b 6 Thread the fixture wire and fixture grounding wire House Groundiia Wire through the collar canopy top loop nipple b and Wire Nut mounting strap Washer 7 Connect the other end of the chain with the top loop dey ea e AR by using the other loop lock Mounting Screw 8 Pull out the outlet wires and the house grounding MIPPIEC wire from the outlet box Make wire connections Canopy using the wire nuts Top Loop The smooth wire marked from the fixture to the Collar black wire from the power source Loop Lock The ridged wire unmarked from the fixture to Fixture Grounding Wire the white wire from the power source Chain Attach the fixture grounding wire to the mounting Loop Lock i Fixture Wire strap with the green grounding screw Then Loop connect it to the house grounding wire with a i Nipple a wire nut Fixture Carefully put the wires back into the outlet box 9 Attach the canopy to the mounting strap by inserting the top loop then secure it with the collar 10 Repeat the steps 6 8 for Light Kit aire aireRyder F A N Page 2 2 091230
Download Pdf Manuals
Related Search