Kenroy Home 93066ORB Instructions / Assembly
Contents
1. INTO THE GROOVE UNDER THE BOBECHE 5 THE SOCKETS HAVE BEEN BENDED FOR SHIPPING STRAIGHTEN THE SOCKETS 6 SLIDE A CANDLE SLEEVE OVER EACH SOCKETI 7 DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG THE FIXTURE AT THE DESIRED HEIGHT USE CHAIN PLIERS OR PLIERS WITH A SCREWDRIVER SEE BELOW TO OPEN ONE LINK ON THE END OF THE CHAIN AND ATTACH THE CHAIN TO THE CHAIN LOOP REMOVE OR ADD CHAIN LINKS FROM THE CHAIN IN ORDER TO ACHIEVE THE DESIRED LENGTH FOR HANGING THE LIGHT FIXTURE THREAD THE FIXTURE AND GROUND WIRES UP THROUGH EVERY OTHER LINK IN THE CHAIN TO OPEN A CHAIN LINK USE A PAIR OF PLIERS AND A SCREWDRIVER AS SHOWN ABOVE TO OPEN A CHAIN LINK WRAP THE JAWS OF THE PLIERS WITH CLOTH TO PROTECT THE FINISH OF THE CHAIN STOP COMPLETE INSTALLATION INSTRUCTIONS ON NEXT PAGE BEFORE CONTINUING TO FINAL ASSEMBLY FINAL ASSEMBLY 1 INSTALL A 60 WATT MAXIMUM CANDELABRA BASE TYPE B BULB NOT INCLUDED INTO EACH SOCKET 2 RESTORE POWER YOUR FIXTURE IS NOW READY FOR USE 1072013 93066ORB INSTRUCTIONS SUPPLY GROUND WIRE OUTLET BOX WHITE BLACK SUPPLY WIRE SUPPLY WIRE CEILIN WIRE CONNECTORS BLACK OR SMOOTH l PCS FIXTURE WIRE l WHITE OR RIBBED 8 32 SCREWS i FIXTURE WIRE SUPPLIED WITH BOX E E NIPPLE ROSSBAR CANOPY IXTURE GROUND WIRE REEN GROUND SCREW SCREW COLLAR NUT SCREW COLLAR LOOP INSTALLATION INSIRUCTIONS READ AND SAVE THESE INSTRUCTIONS CAUTION TO AVO2. ID POSSIBLE ELECTRIC SHOCK MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL IF YOU ARE REPLACING AN EXISTING FIXTURE FIRSTLY TURN THE FIXTURE OFF NEXT TURN THE WALL SWITCH OFF FINALLY GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME TURN THE FUSE OR BREAKER TO THE OFF POSITION SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES IF YOU ARE NOT FAMILIAR WITH WIRING YOU SHOULD USE A QUALIFIED ELECTRICIAN THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE FIXTURE 1 ATTACH THE CROSS BAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE OUTLET BOX NOTE IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT USE THE 2 8 32 x 1 1 4 SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE NEXT SCREW THE SCREW COLLAR LOOP ONTO THE NIPPLE AND THEN SCREW THE NIPPLE INTO THE CROSS BAR 2 SLIDE THE SCREW COLLAR NUT AND THEN THE CANOPY ONTO THE END OF THE CHAIN THEN FASTEN THE END LINK OF CHAIN TO THE SCREW COLLAR LOOP 3 INSERT THE FIXTURE WIRE AND THE GROUND WIRE UP THROUGH THE NIPPLE CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTORS PROVIDED CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE CROSSBAR THEN CONNECT THE FIXTU
3. MODEL 930660FB PACKING DIAGRAM CANOPY CHAIN amp OTHER PARTS E 1 CANDLE SLEEVE 6 PCS STYROFOAM 12 KGS WIRE CONNECTOR G PGS CROSSBAR IPPLE CANOPY SCREW COLLAR NUT SCREW COLLAR LOOP C CHAIN LOOP NIPPLE ARM A 6 PCS ENTER POLE ANDLE SLEEVE SOCKET BOBECHE ROOVE 6 PCS DISTRIBUTOR voz 930660ORB ASSEMBLY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO ASSEMBLY THIS FIXTURE SHOULD TAKE APPROXIMATELY 10 MINUTES TO ASSEMBLE MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED TOOLS YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT LADDER SCREWDRIVER ADJUSTABLE WRENCH WIRE CUTTERS AND PLIERS UNPACK THE FIXTURE YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN THE PACKAGE CANOPY CHAIN CHAIN LOOP COLUMN CENTER POLE ARM A ASSEMBLY FIXTURE BODY 6 CANDEL SLEEVES TO PROTECT THE FINISH PLACE ALL PARTS ON A SOFT SURFACE MOUNTING HARDWARE PACKAGE SCREW COLLAR LOOP SCREW COLLAR NUT NUT NIPPLE 2 8 32 X 1 1 4 SCREWS CROSSBAR GREEN GROUND SCREW AND 3 WIRE CONNECTORS FIXTURE ASSEMBLY 1 SCREW CENTER POLE TO TOP OF THE DISTRIBUTOR 2 SLIDE ARM A ASSEMBLY AND COLUMN OVER THE NIPPLE AND SECURE WITH CHAIN LOOP 3 THE ARM A HAVE BEEN TURNED TO LAY FLAT FOR SHIPPING TURN THE ARMS CAREFULLY SO THAT THEY ARE EVENLY SPACED APART 4 PUSH END OF THE ARM A AND INSERT IT
4. RE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED 4 TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX SPREAD THE ELECTRICAL SPLICES SO THAT THE BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE NEXT RAISE THE CANOPY TO THE CEILING AND SECURE IN PLACE BY SCREWING THE SCREW COLLAR NUT ONTO THE SCREW COLLAR LOOP 8 SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS 10 2013 93066ORB INSTALLATION
Download Pdf Manuals
Related Search