Sea Gull Lighting 65252-824 Installation Guide
Contents
1. INSTALLATION AND SAFETY INSTRUCTIONS GROUNDING AND MOUNTING BAR LOCK UP WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE IS 7 OUTLET BOX REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF GROUND WIRE WIRE dehulled CONNECTORS Carefully remove the fixture from the carton and check that all parts are included as shown in Figures 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be lH M OUTLET BOX installed on a ceiling which contains a radiant type heating system SCREWS Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician WARNING TO REDUCE THE RISK OF FIRE SCREW D NIPPLE C ELECTRIC SHOCK OR PERSONAL INJURY MOUNT TO OUTLET BOX OR SUPPORTING SYSTEM ABLE TO FIGURE 2 NOT INCLUDED SUPPORT THE WEIGHT OF THE FIXTURE FIGURE 1 NOT SUPPLIED lt WIRE CONNECTORS GROUND WIRE lt MOUNTING BAR A OUTLET BOX SCREWS SCREW COLLAR E lt CANOPY H b Ja SOREWC N PE Ss SCREW COLLAR RING G Sea gull lighting Installation And ___ Safety Instruction RING Q HC 6 72 052604 DIFFUSER M Fill In Item Number O2. SE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE SQUARE amp RIDGED PARALLEL WIRE ROUND amp SMOOTH WHITE OR GREY WITH TRACER INNAN NLSN BROWN GOLD OR BLACK WITHOUT TRACER lt WHITE OR GREY WITHOUT TRACER BROWN GOLD OR BLACK WITH TRACER ee Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the Outlet box in the same manner STEP 6 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire F from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A If uninsulated wire is on the mounting bar A connect the ground w
3. ire F from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manu factured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy H against ceiling and screw the screw collar ring G to the screw collar E Raise diffuser M to fixture ring Q Secure in place with rubber washer and nut Install decorative cap R and secure in place with Z STEP 4 Install lamps O D CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
4. n Carton And File This Sheet For Fixture Reference ITEM Line art shown may not exactly match the fixture enclosed DECORATIVE However the installation instructions do apply to this fixture CAP R FINIAL Z INSTALLATION HC 672 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET OX Ww STEP 1 Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that three threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B Attach screw collar E to nipple C STEP 2 Using two pairs of pliers open one link of chain S and connect it to the fixture loop I at the top of the fixture Note If your fixture comes with 2 screw collar STEP 3 rings Select the one of your choice Slide the screw collar ring G and canopy H in that order over chain S Open one link on the other end of the chain S and attach it to the screw collar E which has been mounted to the ceiling nipple C BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 4 Lace wires up through chain S and pass wires through holes in screw collar E We recommend lacing wire up through every other link of chain S STEP 5 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOU
Download Pdf Manuals
Related Search