Sea Gull Lighting 40012-773 Installation Guide
Contents
1. Installation And Safety Instructions HC 753 Saq Gull Lightin Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM __ 082203 FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER SET AT OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician OUTLET BOX S ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in figure 1 and 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture CANOPY I lt GLASS J GLASS RETAINING 9 FING NOT INCLUDED GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX XN GREEN GROUNDING SCREW G NIPPLE F MOUNTING BAR D GROUND WIRE WIRE CONNECTORS NOT INCLUDED FIGURE 2 CAP NUT H FIGURE 1 INSTALLATION HC 753 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Usin2. for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw G is to be inserted into the hole with two raised dimples provided on the mounting bar D Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw G on the mounting bar D if uninsulated wire is on the mounting bar D connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY STEP 1 Make sure no bare wires can be seen outside wire connectors STEP 2 After wires are connected tuck them carefully inside outlet box Push the fixture firmly over the mounting nipple F and against the wall Secure canopy l in place with cap nut H STEP 3 Place glass J over socket and secure in place or by screwing on retaining ring M STEP 4 Install lamps Hd CLEANING To clean wipe fixture body with a soft cloth Clean glass with a m
3. g outlet box screws not supplied fasten mounting bar D to outlet box through slots in mounting bar D STEP 2 Thread nut E onto nipple F so that 5 threads are exposed above nut E Thread that end of the nipple F into mounting bar D and tighten nut E against mounting bar D STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below F GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE pm PARALLEL WIRE ROUND amp SMOOTH f PARALLEL WIRE SQUARE amp RIDGED CS COS WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER amw a BROWN GOLD OR BLACK WITH BROWN GOLD OR BLACK WITH OUT TRACER TRACER ne Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again
4. ild soap Do not use abrasive materials such as scouring pads or pow ders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search