Sea Gull Lighting 6150-44 Installation Guide
Contents
1. n m pe O B of mounting bar against outlet box not supplied and fasten mounting bar through slots in flat strap B to outlet box with outlet box screws K not supplied Be sure the mounting screws are perfectly horizontal so fixture hangs straight FOR CHAIN HUNG ONLY STEP 1 Using 2 pair of pliers open one link of chain Y and connect it to the fixture loop X at the top of the fixture BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 2 Lace fixture wire up through entire chain Y and pass through canopy loop S We recommend lacing wire up through every other link of chain Y A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firm2. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in Figures 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture CAUTION Fixtures with photo cells should be mounted at least 48 from all sides to avoid reflection of light back onto Photo cell causing the Photo cell to malfunction or flicker FIGURE 1 NOT SUPPLIED FOR STEM MOUNT WIRE CONNECTORS MOUNTING SCREWS I CANOPY G gt GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX STRAP B GROUND WIRE MOUNTING SCREWS I OFFSET lt STRAP C GREEN GROUNDING SCREW D OUTLET BOX B SCREWS K FIGURE 2 WIRE CONNECTORS NOT INCLUDED NUT W gt a LOCK WASHER H CANOPY G SS CAP NUTS F Ox NIPPLE M CANOPY LOOP S CHAIN Y FIXTURE LOOP X lt SOCKET ASSEMBLY U FIGURE 3 ASSEMBLY FOR CHAIN HUNG Thread nipple M through canopy loop s Inst
3. all canopy loop s through canopy G secure with lockwasher H and nut W if applicable STEP 2 Install fixture loop X onto socket assembly U STEP 3 Feed the fixture wire from the socket assembly U through the fixture loop X and canopy loop S mounted on canopy G lt ROD ASSEMBLY E RETAINING SCREWS P FIXTURE BODY GUARDS Z GLASS N Note This fixture can be hung using 1 2 or 3 rods Select the number of rods desired Secure rods together if applicable Feed the fixture wire from the socket assembly U through the rod assembly E and coupling J mounted on canopy G Secure rod assembly E to coupling J and socket assembly U Be sure not to damage the fixture wire sea gul lighting Installation And Safety Instruction HC 838 012405 Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 838 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX FOR STEM MOUNT AND CHAIN HUNG STEP 1 Hold mounting bar with flat strap B behind offset strap C Rotate straps so they are at right angles to one another STEP 2 Insert fixture mounting screws I in threaded holes of offset strap C Run screws all the way down to the heads STEP 3 U pe O 4 ped
4. lamp STEP 3 Raise glass N to fixture body and secure with retaining screws P STEP 4 Install guards Z to fixture body CLEANING o clean wipe fixture body witn a soft cloth Clean glass with a mila soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper NOTE For Solid Copper Fixtures Use a good quality automotive wax at least twice a year to protect your fixture If this additional care is not taken your fix ture will turn into a Patina Finish over time ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts Lamp Information LAMP ape lt Socket Ballast e Push Lamp into socket Do not twist
5. ness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 2 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar If uninsulated wire is on the mounting bar connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors FOR STEM MOUNT AND CHAIN HUNG STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy G against ceiling allowing for mounting screws I to protrude through holes in canopy G Secure in place with cap nuts F STEP 2 Install
Download Pdf Manuals
Related Search