Sea Gull Lighting 4702-962 Installation Guide
Contents
1. INSTALLATION AND SAFETY INSTRUCTIONS WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU Carefully remove the fixture from the carton and check that all parts ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED are included as shown in Figure 1 Be careful not to misplace any of OR THE CIRCUIT BREAKER OFF the screws or parts which are needed to install this fixture GENERAL STEP 1 You don t need special tools to install this fixture Be sure to follow the Peel protective coating off as follows if applicable For easier steps in the order given Under no circumstances should a fixture be removal peel coating off at an angle holding it close to the fixture hung on house electrical wires nor should a swag type fixture be Peel sides off before peeling the front faces installed on a ceiling which contains a radiant type heating system NOTE SOCKETS ARE FACTORY INSTALLED Read instructions carefully If you are unclear as to how to proceed IF SOCKET IS NOT SECURE TO BACKPLATE MAKE consult a qualified electrician SURE SOCKET TABS ARE SNAPPED ONTO NOTE Proper wiring is essential for the safe operation of this PRE DRILLED HOLES IN BACKPLATE fixture OUTLET BOX GROUND WIRE D OUTLET BOX BACK PLATE C GREEN GROUNDING SCREW A SOCKETS J EXTRUDED HOLE B DECORATIVE FRONT E WOOD SCREWS K GCO GROUND WIRE IF APPLICABLE FACE PLATE F ROME2. OWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors Note Fixtures that employ a grounded type receptacle are not intended for connection to a two wire ungrounded source of supply Tuck wires into outlet box Attach backplate C to outlet box by placing outlet box screws not supplied through punched out holes in backplate C If applicable Wood screws K placed in outer holes will provide additional support Note Your fixture may be supplied with a faceplate F decorative front E or both depending on your model Follow the directions below according to the parts supplied with your fixture Position faceplate F or decorative front E over sockets J NOTE If backplate C is supplied with mounting studs H position faceplate over studs and secure in place with cap nuts G For fixtures supplied with cups Push faceplate F or decorative front E to wall and secure by pushing cups I onto sockets J in a clockwise motion If your fixture is supplied with threaded sockets thread rings L onto sockets J in the same manner except screw them on NOTE If both decorative front E and faceplate F are supplied place faceplate F and wood or mirror in that order over sockets J before securing with cups or rings L NOTE It may be necessary to bend tabs in cup l for a tighter fit Install lamps CLEANING To clean wipe fixture with a soft cloth Clean gl
3. WN GOLD OR BLACK WITH TRACER NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire S from group A and place evenly against the black wire from the outlet box Do Not twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw A is to be inserted into the hole with two raised dimples provided on the back plate C Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulat ed wire around the green grounding screw A on the back plate C NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE P
4. X BX FIGURE 1 BACK PLATE CONNECTOR lt cups l NOT SUPPLIED fe oed Gull lighting Installation And Safety Instruction HC 1 07 100101 Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM FIGURE 2 NOT SUPPLIED ALTERNATIVE MOUNTING METHOD Fig 2 HC 107 THIS FIXTURE CAN BE MOUNTED TO A WALL WITHOUT AN OUTLET BOX MAKING THE WIRING CONNECTION BETWEEN THE FACEPLATE AND BACKPLATE 1 Remove knock out from the backplate if applicable or remove plastic bushing Install Romex Bx connector on the backplate Feed house supply wires through Romex Bx connector and secure 4 Make wiring connection as described in the steps that follow and tuck the wires between the faceplate and backplate INSTALLATION TO AN OUTLET BOX Fig 1 STEP 1 Punch out appropriate holes in backplate C if applicable to correspond with holes in outlet box STEP 2 Push socket wires thru plastic bushing STEP 3 A Take note of the color of the wire S on your fixture Identify which group your fixture wire S falls into and connect the wires according to the directions below on tT GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE SS CI PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED c s WHITE OR GREY WITH TRACER ee BROWN GOLD OR BLACK WITHOUT TRACER WHITE OR GREY WITHOUT TRACER BRO
5. ass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search