Sea Gull Lighting 16006-15 Instructions / Assembly
Contents
1. 16002 15 16002 15 INSTRUCTIONS FOR YOUR NEW REMOTE FAN CONTROL SYSTEM CAUTION This remote only works with some fans in sloped ceiling model Do not use fan speed control in canopies where the mountng is not as described in figure 6 7 WARNING HIGH VOLTAGE Before Connecting the Control Unit eRemove electrical power from circuit to be used eHousehold power can cause SERIOUS INJURY or DEATH eWiring must meet all local electrical code require ments A SETTING THE CODE ON YOUR NEW REMOTE Fig 1 Sdi V 1 Remove battery cover a 7 Refer to pg 5 for removing battery cover Transmitter 2 Slide code switches to your choice of UP and DOWN positions Code switches Factory setting is all UP Do not use this setting Fig 1 eUse ball point pen or small screwdriver eSlide firmly up or down B SETTING THE CODE ON YOUR NEW CONTROL UNIT Fig 2 1 Slide code switches to the same positions as set on your REMOTE NOTE The code switches on the TRANSMITTER and the RECEIVER UNIT must be set to the same positions to work The item IC before the radio certification number only signifies that Industry Canada Technical specifications were met Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Receiver Code switches Fig 2 16002 15 LIMITED WARR2. ANTY A GEOGRAPHIC SCOPE This warranty applies to products purchased in the United States and Canada B What is Covered Any defect in material or workmanship C For how long from date of purchase All finished products one year all spare parts 90 days D Who gets the warranty This warranty is limited to the customer who originally purchased the prod uct E LIMITATIONS IMPLIED WARRANTIES INCLUDING THOSE OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY AN UNWRITTEN WARRANTY THAT THE PRODUCT IS FIT FOR ORDINARY USE ARE LIMITED TO ONE YEAR FROM THE DATE OF PURCHASE WILL NOT PAY FOR LOSS OF TIME INCONVENIENCE LOSS OF USE OF YOUR PRODUCT OR PROP ERTY DAMAGE CAUSED BY YOUR PRODUCT OR ITS FAILURE TO WORK ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES RESULTING FROM MISUSE OR MODIFICATION OF YOUR PRODUCT SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSIONS MAY NOT APPLY TO YOU F How to obtain warranty service To obtain warranty service for your product you must provide proof of the date and place of purchase of the product 1 Do it yourself service Call the Consumer Line at 800 519 4092 Trained representatives will assist you in diagnosing the problem and will arrange to supply you with the required part for do it yourself repairs G What this warranty does not cover This warranty does no
3. LACK wires on one side of box and WHITE GREEN and BARE wires on the other side of the box Connect RED Control Unit wire MOTOR L to BLACK fan wire Connect BLUE Control Unit wire FOR LIGHT to BLUE light wire FIGURE 4 FIGURE 5 FLUSHMOUNT FANS ONLY FLUSHMOUNT FANS ONLY 16002 15 12 Push the connected wires up into the junction box 13 Lay the BLACK Control Unit wire Antenna on top of the Control Unit 14 FOR FANS ON A DOWNROD Lay the Control Unit in the CANOPY See Fig 6 FOR FLUSHMOUNT FANS Attach Control Unit to mounting plate or to ceiling with tie wraps supplied See Fig 7 NOTE If the unit does not fit properly between the mounting plate and ceiling attach the unit to the underside of the mounting plate 15 FOR FANS ON A DOWNROD Reinstall the CANOPY on its mounting plate Go to step 17 FOR FLUSHMOUNT FANS Reconnect mounting bracket to mounting place See Fig 4 16 FOR FLUSHMOUNT FANS Reinstall the decorative housing on its mounting plate 17 Restore electrical power to the circuit FIGURE 6 FIGURE 7 DOWNROD FANS ONLY FLUSHMOUNT FANS ONLY JUNCTION BOX CEILING l CONTROL UNIT LI Li L MOUNTING PLATE IMPORTANT Fan Installation must be complete INCLUDING ASSEMBLY OF BLADES before testing remote control unit 1 This unit operates on one 12 volt battery included Duracell MN21 Eveready A23 GP23A all 12v 2 Store the controller unit away from excess heat or humidity 3 This remo
4. o turn off press once quickly while light is on To dim light hold down button light dimmer The light will cycle from bright to dim to bright until button is released Light will maintain last setting if turned off For Customer Service Call 866 449 2821
5. t cover service charges batteries installa tion defects resulting from accidents or damage resulting from alterations misuse or abuse lack of proper installation or maintenance failure to follow instructions unauthorized repair damage caused by affixing of any attachment not provided with the product failure of supporting devices not supplied as original mount ing hardware exposure to extremes of heat or humidity incorrect wiring or voltages or failures caused by modifications of the product fire flood or acts of God THIS WARRANTY IS THE ONLY ONE WE WILL GIVE ON YOUR PRODUCT IT SETS FORTH ALL OUR RESPON SIBILITIES REGARDING YOUR PRODUCT THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES TROUBLESHOOTING GUIDE NOTICE FAILS TO OPERATE Your Ceiling Fan and Light Assembly Must Meet the Following Requirements Is there power to the Control Unit Is the Control Unit wired correctly DO NOT USE WITH SOLID STATE FANS Are the fan and light switches set on the highest position ELECTRICAL Is there a good battery in the REMOTE If the red 120 Volts AC 60 Hz indicator lights when either button is pushed the Max Motor Amps 1 0 CEILING FAN ONLY battery still may be bad Try changing your battery Max Light Watts 240 INCANDESCENT ONLY first Are the switches set the same in both REMOTE and MECHANICAL the Control Unit The decorative housing CANOPY at the ceiling Must Be Metal SHORT RANGE The metal housing acts as a pro
6. te control unit is equipped with 16 code combinations Because of the many combinations inter ference from other remotes is possible i e garage openers car alarms security systems etc If your fan light goes on or off without using your remote simply change the codes on both the control unit in the fan and in your remote transmitter 4 THE FAN AND LIGHT MUST BE SET AT THEIR HIGHEST BRIGHTEST SETTINGS BEFORE STARTING In order to operate your fan using the remote make sure the fan is set on HIGH and the light is in the ON or BRIGHTEST position by using the pull chain controls originally supplied with your fan 5 Operation buttons on the panel of the transmitter eee For FAN High speed ee For FAN Medium speed e For FAN Low speed Square For FAN Off For Light brightness and on off control 6 To turn ON the FAN press the selected speed button to run the fan at the desired speed 7 To turn OFF the FAN press the Square button 8 For LIGHT control e Turn the light on or off by pressing the light button e If you keep the light button pressed the light will dim go off and come back on at the brightest level The light will continue to make this cycle until the button is released If you turn your power source off the settings on your fan and light will remain the same when you turn the power back on YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN LIGHT 16002 15 The wall control transmits
7. tective cover for the Control Unit If the REMOTE operated the Control Unit when close to it but does not operate it at distances of 30 to 40 DO NOT USE WITH A NON METALLIC HOUSING feet try placing the Black Antenna wire above the ceiling and outside of the junction box ONE YEAR LIMITED WARRANTY FOR HELP CUSTOMER HELP LINE AVAILABLE for INSTAL LATION AND TROUBLESHOOTING Call Customer Help Line at 800 519 4092 16002 15 INSTRUCTIONS FOLLOW ALL SAFETY INSTRUCTIONS IN YOUR CEILING FAN INSTRUCTION MANUAL REMEMBER TO REMOVE ELECTRICAL POWER BEFORE STARTING WORK WIRING MUST MEET ALL ELECTRICAL CODES A MAKING THE ELECTRICAL CONNECTIONS See Fig 3 Ni USE WIRE NUTS FOR ALL CONNECTIONS FIGURE 3 CYNNGLNY z219 CONTROL AC SUPPLY BLACK BARE GROUND Remove electrical power from the circuit FOR FANS ON A DOWNROD Remove ceiling fan CANOPY from its mounting plate Go to step 4 FOR FLUSHMOUNT FANS Remove decorative housing from mounting plate See Fig 4 FOR FLUSHMOUNT FANS Disconnect mounting bracket from mounting plate and allow to hang from one side See Fig 5 Disconnect existing wiring from supply at ceiling Connect GREEN fan wire to BARE ground wire Connect BLACK Control Unit wire to BLACK supply wire AC L Connect WHITE Control Unit wire to WHITE wire of supply AC N Connect WHITE Control Unit wire MOTOR N to WHITE fan wire Push the connected wires up into the junction box Place B
8. the command signals via radio waves to the receiver installed in the fan s hanging bracket or on the fan The receiver is required for the wall control to function Power for the wall control comes from the 12V bat tery located in the wall remote Duracell MN21 Eveready A23 GP 23A all 12V The frequency switches dip switches on the wall control and the receiver have been preset at the factory Please recheck to make sure the switches on the wall control and receiver are set to the same position Any combination of settings are fine as long as the wall control and ceiling fan receiver are set to the same posi tion CAUTION TURN OFF POWER AT FUSE BOX TO AVOID POSSIBLE ELECTRICAL SHOCK Place face plate over battery compartment and buttons Place remote over 2 pins on front cover Attach cover of remote by placing over 4 pins and snaping into place Attach front cover to wall control Install wall control unit to outlet box with screws provided Snap battery using machine screws provided cover in place 16002 15 Remote Control Transmitter Features LED LIGHT MEDIUM SPEED LOW SPEED FAN OFF SETTING Turns fan off only LIGHT ON OFF SETS TING AND DIMMER Press and hold to dim light infinitively FAN SPEED Depress I dot for low speed 2 dots for medium or 3 dots for high To turn fan off press square LIGHT DIMMER To turn light on press light dimmer once quickly T
Download Pdf Manuals
Related Search