Kenroy Home 32618ORB Installation Guide
Contents
1. SWING OR HAVE ABNORMAL SOUND PUT DROP WD 40 OR SIMILAR PRODUCT ON THE JOINTS AND LET IT SIT OVERNIGHT DRY WITH A SOFT CLOTH PRIOR TO ASSEMBLY 1 REMOVE MOUNTING PLATE FROM BACKPLATE ASSEMBLY BY UNSCREWING 3 SMALL SCREWS 2 POSITION THE MOUNTING PLATE ON THE WALL AT DESIRED LOCATION AND MARK THE PLACE FOR THE PLASTIC ANCHORS TO BE INSTALLED 3 DRILL PILOT HOLES ON THE MARKED SPOTS AND INSERT PLASTIC ANCHORS IF FASTENING WITH WOOD SCREWS TO STUD SKIP THIS STEP NOTE THE MOUNTING PLATE SHOULD BE MOUNTED ON A WALL STUD USING A SCREWDRIVER IF MOUNTING ON A HOLLOW AREA DRILL 1 4 PILOT HOLES AND INSERT PLASTIC ANCHORS WHERE THE LOCATION WAS MARKED 4 THE MOUNTING THE PLASTIC 5 THE 5 5 YOU MARKED STUD SECURE WITH 4 WOOD 5 RAISE THE BACKPLATE ASSEMBLY TO THE WALL THEN SECURE THE BACKPLATE ASSEMBLY TO MOUNTING PLATE WITH 3 SMALL SCREWS REMOVED ABOVE 6 PLACE A SHADE OVER THE SOCKET AND THEN SECURE WITH THE SOCKET RING 7 INSTALL 100 MAX MEDIUM BASE TYPE A BULB INCLUDED INTO SOCKET 8 INSTALL CORD COVER MOUNT CHANNEL ON THE WALL WITH WOOD SCREWS AND PLASTIC 5 WITH CORD BEHIND COVERS PRESS CORD COVERS ONTO CHANNEL 9 PLUG THE POWER CORD INTO AN OUTLET AND TURN ON AT SWITCH 12 2014 32618ORB INSTRUCTIONS RNG SHADE 32618SHORB REPLACEMENT PART MOUNTING BLACK P2. LATE FIXTURE WIRE 4 8 32 1 1 4 SMALL SCREW SCREWS 2 PCS a WIRE SOCKET CONNECTOR 3 ASSEMBLY BLACK SUPPLY WIRE WHITE SUPPLY WIRE SUPPLY GROUND WIRE OUTLET BOX FIXTURE GREEN GROUND WIRE GROUND SCREW OUTLET BOX INSTALLATION WALL READ AND SAVE THESE INSTRUCTIONS CAUTION TO AVOID POSSIBLE ELECTRIC SHOCK MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL IF YOU ARE REPLACING AN EXISTING FIXTURE FIRSTLY TURN THE FIXTURE OFF NEXT THE WALL SWITCH OFF FINALLY GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME TURN THE FUSE BREAKER TO THE OFF SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES F YOU DO NOT HAVE ELECTRICAL WIRING EXPERIENCE HAVE YOUR FIXTURE INSTALLED BY A QUALIFIED LICENSED ELECTRICIAN THIS FIXTURE IS TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE WEIGHT OF THIS FIXTURE THE OUTLET BOX MUST BE DIRECTLY SUPPORTED BY THE BUILDING STRUCTURE NOTE IF WIRING TO OUTLET BOX FOLLOW INSTRUCTIONS BELOW IF USING POWER CORD PROCEED TO ASSEMBLY INSTRUCTIONS INSTALL THE FIXTURE 1 REMOVE MOUNTING PLATE FROM BACKPLATE ASSEMBLY BY UNSCREWING 3 SMALL SCREWS 2 REMOVE POWER REFER TO REMOVING THE POWER INSTRUCTIONS 3 ATTACH MOUNTING PLATE TO OUTLET BOX USING TWO SCREWS PROVIDED WITH THE OUTLET BOX NOTE IF THE SCREWS
3. MODEL 52618 SHADE 2 PCS BACKPLATE ASSEMBLY MOUNTING PLATE 2 CORD COVERS SOCKEY RING 2 PCS MOUNTING CHANNEL amp 3 SMALL SCREWS 5 5 SHADE 32618SHORB REPLACEMENT PART CORD COVER SMALL SCREW Z PLASTIC 09 ASSEMBLY WOOD SCREW 2 PCS CHANNEL CORD COVER POWER CORD CORD COVER ORD ASSEMBLY INSTRUCITIIONS CORD COVER ASSEMBLY READ AND SAVE THESE INSTRUCTIONS READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO ASSEMBLY THIS LAMP SHOULD TAKE APPROXIMATELY 5 MINUTES TO ASSEMBLE MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED CAUTION INJURY PERSONS AND DAMAGE TO THE LAMP AND OR MOUNTING SURFACE MAY RESULT IF THE LAMP IS PULLED AWAY FROM THE SURFACE TO REDUCE THE LIKELIHOOD OF SUCH INJURY OR DAMAGE MOUNT ONLY ON A SURFACE IS MECHANICALLY SOUND TOOLS YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT SCREWDRIVER AND DRILL UNPACK THE CHECK THE CONTENTS OF THE BOX YOU SHOULD HAVE THE FOLLOWING BACKPLATE SHADE SOCKET ASSEMBLY AND ARM PACKAGE 2 8 32 x 1 1 4 MOUNTING SCREWS 6 WOOD SCREWS 6 PLASTIC ANCHORS 2 CORD COVERS MOUNTING CHANNEL NOTE IF USING POWER CORD FOLLOW INSTRUCTIONS BELOW IF WIRING TO AN OUTLET BOX PROCEED TO OUTLET BOX INSTALLATION INSTRUCTIONS ASSEMBLE THE FIXTURE NOTE SWING THE SWING ARM IF THE SWING ARM 15 HARD TO
4. POWER CORD BY TWISTING COUNTER CLOCKWISE SEE DIAGRAM 2 UNTIE SAFETY PULL POWER OUT THROUGH 3 FOLLOW OUTLET BOX INSTALLATION INSTRUCTIONS FOR WIRING TO AN OUTLET BOX 12 2014 32618ORB INSTRUCTIONS
5. WITH THE OUTLET BOX ARE TOO SHORT USE THE 2 8 32 x 1 1 4 SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE 4 CONNECT THE WHITE RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE MOUNTING PLATE THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED 5 RAISE BACKPLATE ASSEMBLY TO THE WALL AND CAREFULLY TUCK THE WIRES INSIDE THE OUTLET BOX SPREAD THE ELECTRICAL SPLICES SO THAT THE BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE THEN SECURE THE BACKPLATE ASSEMBLY TO MOUNTING PLATE WITH 3 SMALL SCREWS REMOVED ABOVE 6 PLACE A SHADE OVER THE SOCKET AND THEN SECURE WITH THE SOCKET RING 7 INSTALL 100 WATT MEDIUM BASE TYPE INCLUDED INTO 5 8 RESTORE AND TURN AT YOUR NEW FIXTURE IS NOW READY FOR USE L 12 2014 32618ORB INSTRUCTIONS THE POWER 2 PCS SAFETY REMOVING THE POWER THE POWER CORD IS THE WIRE THAT ENTERS THROUGH THE OF 1 REMOVE THE 2 WIRE CONNECTORS THAT CONNECT TO
Download Pdf Manuals
Related Search