Filament Design V4155-65 Installation Guide
Contents
1. Medium 3603 70 29 4 422 57 High 5813 49 66 5 87 42 ee ee a ann S e ord ratana a aa aa Ceiling fan airflow is measured in cubic feet per minute CFM Pow seis i s imize e j ower use is measured in watts To maximize energy savings iMeduured sooerding Choose a fan with high airflow efficiency CF Miwalt to ihe ENERGY STAR Use ENERGY STAR labeled lighting in your fan aparoved Solid State 2 Remember to switch off your fan when you leave the room lest method 122. mounted with a minimum of 7 feet from the trailing edge of the blades to the floor 7 Do not operate reversing switch while fan blades are in motion Fan must be turned off and blades stopped before reversing blade direction 8 Avoid placing objects in the path of the biades 9 To avoid personal injury of damage to the fan and other items be cautions when working around or cleaning the fan 10 Do not use water or detergents when cleaning the fan or fan blades Adry dust cloth or lightly dampened cloth will be suitable for most cleaning 144 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side or the outiet box 42 Electrical diagrams are for reference only Light kits that are not packed with the fan musi be U_L Listed and marked suitable for use with the mode fan you are installing Switches must be UL general use switches Refer to the instructions packaged with the light kits and switches for proper assembly 13 WARNING To reduce the risk of personal injury do not bend the biade brackets aiso referred to as flanges during assembly or after installation Do not insert objects in the path of the blades NOTE The important safeguards and instructions appearing in this manual are not meani to cover al possible conditions and situations thai may oc
3. your optional light kit Fan controlled putt chain switch Light contraolied from wall switch Fan controlled by pull chain switch Light controlled by slide switch ae a POWER LINES 4 mmo POWER LINES 120V ajzu WIRING fae e alelols 4 GREEN kd GS a a 4 GROUND 1 1g WIRING 1 i i BOX i ii f 7 GROUND TO _ _1 GROUND TO z MOUNTING 2 Z ja MDUNTING ie BRACKET 3 21 BRACKET OR DOWNROE OR DOWNROD RAN FAN LIGHT Figure 19A Fan and light controlled by POWER LINES independent wall switches WIRING Box E epi 120V Nu BF je GREEN gia eee er om LIGHT iO id arnt 1 GROUND TS t 93 MOUNTING je BRACKET OR DOWNROD FAN Figure iC imiten ey Aor ATTACHING THE FAN BLADES Step 1 Attach the blade to the blade bracket using the screws and fiber washers as shown in Figure 11 Start screw into bracket Repeat for the two remaining screws Step 2 Tighten each screw securely starting with the center screw Make sure the blade is straight Step 3 Fasten blade assembly to motor using the screws supplied Fig 12 Step 4 Install optional light kit if you wish Follow the instructions included with the light kii Screws Z i Fiber washer _ smeuert Blade Blade bracket Figure 41 INSTALLING 4 OR 5 BLADES r your fan hos 4 or 5 blades adaptable motor refer to the following step for Installation Attach four or five blad
4. A autiypna Bi ep gar em O A A beat rine SONNE fete ee ae pean ete MMM Ay i Se a ene oe aenn ngs Vetoes dmija snaar patan rep tate tn Belvo tome ot TOOLS AND MATERIALS REQUIRED YK UN i j 9 1 rerrewmeioh sken todda 9 Nie cuttets Wing suoples as aquired by electicol code GENERAL Afieropening the ceiling fan box youshould find the foltowlng parts 29398098 Fan motor assembly Conosy may with downrod cr mounting plate Blode set Blade brockel set Packoge hardware Wood tassels Light kitfoptional Giass shadsicptional mome oo CEILING FAN INSTALLATION amp OPERATION INSTRUCTIONS IMPORTANT SAFEGUARDS Toreduce the risk of electric shock insure electricity has been turned off at the circuit breaker of fuse box before beginning 2 All wiring must be in accordance with the Nationat Electrica Code and focal electrical codes Electrical installation should be performed by a qualified licensed electrician 3 WARNING To reduce the risk of electrical shock and fire do not use ihis fan with any solid state fan speed contro device 4 CAUTION To reduce the risk of personal injury use only the two steel screws and lock washers provided with the outlet boxes 5 The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 50 pounds Use only U L Listed outlet boxes marked FOR FAN SUPPORT 6 The fan must be
5. cur lt must be understood that common sense caution and carefulness are factors person s caring for and operating the unit Leteri ceprenabemes an OF fae ttt nego 1s VW PF hE EW 2 Dn a bri if there isn t an existing UL listed mounting box then read the following instructions Disconnect the power by removing fuses or turning off circuit breakers Secure the outlet box directly to the building siructure Use appropriate fasteners and building materials The outlet box and its support must be able to fully e the moving weight of the fan at least 50 ibs Do not uss plastic outlet Ox Figures 1 2 and 3 are examples of different ways to mount the outlet box in different situations Alonger downrod may be required in sloped ceiling situations to maintain proper blade clearance To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar as shown in Figure 4 Outlet box Figure 1 Provide strong lt support Recessed outlet box PSS Gating mounting plate Outlet box Figure 4 I TS ee E INSTALL MOUNTING BRACKET To avoid possibla elgcirital shock be sure slactriclty is umag off al the main power panel before wiring All wiring must be in accordance with Natlonal and Local Electrical Codes and the ceiling fan must be grounded as a precaution against possible electrical shock Attach hanger bracket io outlet box
6. e assembiles to motor using the eight or ten screws Moke sure ail screws are tightened securely tr The inner holes are for 4 blades peene The outer holes are for blades aeeareane Figure 12 m A an t aR tae IPEER ee swem yh teeth EE rt TTE EMI Ree ae aaan 9 LIGHT KIT INSTALLATION Optional Be sure all power to the fan is off before beginning to install the light kit by turning off circuit breaker or removing fuse at fuse box Turning power off at switch is not sufficient te prevent electrical shock For Type A Center Nipple Attachment as shown in Fig 13 1 Remove the switch box housing cover from the motor assembly by unscrewing the ry three screws 2 Remove the threaded plug from the center of this cover by pushing out discard this piug or keep it for future use 3 Attach the cover to the fixture by feeding the kit wires black and white through the hale of the cover and screw it onto the fixture threaded post Thread the post washer and nut provided with the light kit hardware bag Onto the post until snug against the inside of ihe switch cover plate Be sure itis tight enough to prevent the light kit from vibrating loose 4 Locate two single wires in switch housing White and blue labeled for tight 5 Connect tihem to the light kit wires White to white Blue to black Note If the wire connector from the fan switch box does not marry with the wire connector of
7. nst connector yoke Some models have 2 downrod seiscrews Repeat fa both Fig 7 Downrad setscrews oe Figure 7 Tighten motor setscrew Check the strength of this connection pre tightened at factory by holding the motor housing in position and iurning the downrod counter clockwise f this connection slips re tighten motor selscrew and iocknut Follow the same procedure as mentioned above for downrod seiscrew Install bail into hanger bracket opening The hook opposite of the hanger brackei opening should fit in slot on ball Fig 8 Figure 8 Make wire connections Refer to section titied Electrical Connections ARNING To avoid damaging the blade arms and blades do not install either unti 1 is fastened to ceiling To avoid motor shift handle fan by downred or switch using only FINISHING THE INSTALLATION 2p 1 Slide the canopy up to the ceiling and over the 2 screws on the hanger ickei Rotate canopy to lock in place ITE Adjust the canopy screws as necessary unti the canopy snug Fig 9 Cutiet box Hanger bracket Hangaren i bal a eae Canopy Figure 9 fa Screws ELECTRICAL CONNECTIONS Make electrical connections Connect black to black white to white and green grounding lead to grounding conductor of supply circuit Make sure that fan is properly grounded Carefully push all wiring inside wiring box after splices are made The blue wire fs for
8. oves warm air off the ceiling area as shown in Figure 16 This allows you to set your heating unit on a lower setting without affecting your comfort TROUBLESHOOTING PROBLEM SOLUTION Fan will not 1 Check circuit fuses or breakers start 2 Check line wire connections to the fan and switch wire connections in the switch housing CAUTION Make sure main power is off Fan sounds Make sure all motor housing screws are snug noisy 2 Make sure the screws that attach the fan blade bracket to the motor hub are tight 3 Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing CAUTION Make sure main power if off 4 Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this time 5 lf using an optional light kit make sure the screws securing the glassware are tight Check that light bulb is also secure 6 Some fan motors are sensitive to signals from solid state variable speed controls If you have installed this type of control choose and install another type of contro 7 Make sure the upper canopy is a short distance from the ceiling it should not touch the ceiling T Dimote ce a PERFORMANCE loners AND ENERGY 7 INFOR a sR maman wn ia a WE ELLEN oppi omes reemer oprea phet tatane OE sm meyer annem FANSPEED AIRFLOW FANPOWERCONSUMPTION AIRFLOW EFFICIENCY CFM walls CFM watl Low 4707 94 8 9 191 90
9. rn off power at first For type C Light fixture is already pre installed onto the switch housing As shown in Figure 15 i Install a 60 watt max Bulb not provided and glass shade Gently tighten the 3 thumb screws do not over tighten 2 Restore power and your light kit is ready for operation 3 if the light kit does not work turn off the electricity and lower either the canopy or the decorative housing on your ceiling fan to make sure the bulb wire ts connected to the black household wire Switch housing Switch housing Screws Hee Nt Li ght kit Light kit Screws Lt ght kit T Switch housing 8 E ee Figure 45 an Glass skade Figure 13 10 Arteta eee oe seme eppnaamaus eee pr aaaeaii amaaa NOTE Wait for fan to stop before changing the setting of the slide switch Turn on the power and check operation of fan The pull chain controls the fan speet as follows 1 pulls High 2 pults Medium 3 pulls Low and 4 pulls Off Speed settings for warm or cool weather depend on factors such as the room size ceiling height number of fans and so on The slide switch controls directions forward switch down or reverse switch up Warm weather Forward A downward flow creates a cooling effect as shown in Figure 17 This allows you to set your air conditioner on a higher setting without affecting your comfort Cool weather Reverse An upward airflow m
10. the light kit cut off the connectors and join the wires with wire nuts 6 Carefully push all wires back into switch housing of fan then replace the cover with original screws 7 Install 60 watt imax Bulb inot provided and glass shades provided with the light kil Do not over tighten 8 Restore the power and ycur light kit is ready for operation 9 If light kit does not work you need to lower either canopy or decorative housing on your ceiling fan to make sure the blue wire is connected to black household wire Please refer to electrical connection section You may Tighten fitter screws For type B Light kit center mounting cover attachment as shown following Fig 14 light kit without center mounting box 4 Locate the two single wires in the switch box housing white and blue labeled for fight 2 Make wire connections white to white blue to black NOTE if the light kit wire from the fan switch box does not marry with the wire connector of the light kit cut off the connectors and join the wires with wire nuts 3 Carefully push all wires into switch housing 4 install 60 watt max Bulb not provided and glass shades Tighten shade fitter screws until itis against the glass Do nat over tighten 5 Restore power and your tight kii is ready for operation 6 If fight kit does not work lower the decorative housing canopy and check wiring connections Ensure the biue wire is attached to the black wire Remember tu
11. using screws and spring washers provided with the outlet box Fig 5 Install square rubber washers between bracket and autlet box to reduce vibration of metal to metal surfaces Metal an Quilet box Rubber washer Hanger bracket Spring washer wm CY Screws A Figure S e sernpre y apa ao LRE T aA peste E E INSTALLING THE FAN Slide the canopy on the downrod Fig 6 Thread the power leads from the far through theosrepy and downed Take extta cara notte pull on power wires Damage and loose connections could result from any abnormal pressure or these wires Set downrod into downrod collar yoke Route until the hole match Being careful not to damage wiring Insert connector pin through the holes See Fig SA 6B Secure the pin by inserting the stop pin through thi connector pin Downrods Mounting collar yoke Connecting pin Figure SA Canopy Figure 6 Figure 6B WARNING Do not force connector pin through downrod Use of force coule cause damage to wires inside Make sure the stop pin is properly engaged te prevent it from falling out 2 Tighten downrod setscrew Some models have a locknut for the setscrew Tc insure the setscrew fully seats against the downrod itis necessary to back of the locknut until it contacts the setscrew head prior ta tightening the setscrew When setscrew is tighten againsst downrod locknui should then be tightenec agai
Download Pdf Manuals
Related Search