Kenroy Home 93423BRZ Installation Guide
Contents
1. OF THE CANOPY STOP COMPLETE INSTALLATION INSTRUCTIONS ON NEXT PAGE BEFORE PROCEEDING Sus FINAL_ASSEMBLY REPLACEMENT PART 1 INSTALL 100 MAXIMUM MEDIUM BASE TYPE BULB NOT INCLUDED INTO EACH SOCKET 2 SLIDE THE DIFFUSER INTO THE SHADE MAKE SURE THE DIFFUSER IS SECURED BY THE RING OF THE SHADE IFFUSER 3 RESTORE POWER YOUR FIXTURE IS NOW READY FOR USE AVAILABLE PART 93423SHBRZ SHADE 04 2014 93423BRZ ASSEMBLY INSTRUCTIONS SUPPLY OUTLET BOX WHITE SUPPLY WIRE WIRE CONNECTORS 3 PCS BLACK SUPPLY CEILING WHITE O SM at i MOUNTING 8 52 5 5 WITH D 2 8 32 1 1 4 SCREW GREEN 5 e TII NIRIZQ_ 2 PCS SWIVEL EXTENSION TUBE INSTALLATION INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS CAUTION TO AVOID POSSIBLE ELECTRIC SHOCK MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL IF YOU ARE REPLACING AN EXISTING FIXTURE FIRSTLY TURN THE FIXTURE OFF NEXT TURN THE WALL SWITCH OFF FINALLY GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME TURN THE FUSE OR BREAKER TO THE OFF POSITION SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER ALL WIRING MUST2. 954258 2 _ DIAGRAM ARDBOARD CANOPY WITH SWIVEL MOUNTING PLATE AND OTHER 5 IXTURE BODY EXTENSION TUBES amp 2 FINIALS 4 lt BOX FOR IFFUSER 9 5425 7 ASSEMBLY 5 READ THESE INSTRUCTIONS READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO ASSEMBLY THIS FIXTURE SHOULD TAKE APPROXIMATELY 10 MINUTES TO ASSEMBLE MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED TOOLS YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT LADDER SCREWDRIVER ADJUSTABLE WRENCH WIRE CUTTERS AND PLIERS UNPACK THE FIXTURE YOU SHOULD HAVE RECENED THE FOLLOWING CANOPY WITH SWIVEL 3 12 1 6 EXTENSION TUBES BODY WITH 2 FINIALS SHADE DIFFUSER PROTECT THE FINISH PLACE ALL PARTS ON A SOFT SURFACE MOUNTING HARDWARE PACKAGE 4 8 32 x 1 1 4 SCREWS 2 NUTS MOUNTING PLATE GREEN GROUND SCREW 3 WIRE CONNECTORS AND 2 BALL FINIALS FIXTURE ASSEMBLY 1 REMOVE THE 2 FINIALS FROM THE FIXTURE BODY THEN FIXTURE INIAL SECURE THE SHADE TO THE FIXTURE BODY WITH 2 FINIALS REMOVED ABOVE 2 FEED WIRE UP THROUGH TUBING AND WORKING UPWARDS TOWARD CANOPY AS SHOWN 3 SCREW EXTENSION TUBE TO TOP OF THE FIXTURE BODY USE ANY SINGLE LENGTH OF EXTENSION TUBE OR CONNECT TUBE SECTIONS TOGETHER TO OBTAIN DESIRED LENGTH 4 SCREW THE EXTENSION TO THE ON
3. BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES F YOU ARE NOT FAMILIAR WITH WIRING YOU SHOULD USE A QUALIFIED ELECTRICIAN THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE FIXTURE COMPLETE FIXTURE ASSEMBLY INSTRUCTIONS FIRST SEE PREVIOUS 1 SCREW 2 8 32 x 1 1 4 SCREWS INTO THE MOUNTING PLATE MAKING SURE THAT THEY LINE UP WITH THE HOLES IN THE CANOPY THE MOUNTING PLATE TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE OUTLET BOX NOTE IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT USE THE 2 8 32 x 1 1 4 SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE 2 CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTORS PROVIDED THE BLACK OR 5 FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE MOUNTING PLATE THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED 3 TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX SPREAD THE ELECTRICAL SPLICES SO THAT THE BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE 4 RAISE THE FIXTURE TO THE CEILING AND SECURE IN PLACE WITH 2 FINIALS 5 SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS 04 2014 93423BRZ INSTALLATION
Download Pdf Manuals
Related Search