Kenroy Home 91735ORB Installation Guide
Contents
1. LOOP lt lt INSTALLATION INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS CAUTION TO AVOID POSSIBLE ELECTRIC SHOCK MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL IF YOU ARE REPLACING AN EXISTING FIXTURE FIRSTLY TURN THE FIXTURE OFF NEXT TURN THE WALL SWITCH OFF FINALLY GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME TURN THE FUSE OR BREAKER TO THE OFF POSITION SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES IF YOU ARE NOT FAMILIAR WITH WIRING YOU SHOULD USE A QUALIFIED ELECTRICIAN THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE FIXTURE COMPLETE FIXTURE ASSEMBLY INSTRUCTIONS FIRST SEE PREVIOUS PAGE 1 ATTACH THE CROSSBAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE OUTLET BOX NOTE IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT USE THE 2 8 32 x 1 1 4 SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE NEXT SCREW THE SCREW COLLAR LOOP ONTO THE NIPPLE AND THEN SCREW THE NIPPLE INTO THE CROSSBAR 2 SLIDE THE SCREW COLLAR NUT AND THEN THE CANOPY THAT HAS ONE HOLE ONTO THE END OF THE CHAIN THEN FASTEN THE END LINK OF CHAIN TO THE SCREW COLLAR LOOP 5 INSERT THE FIXTURE WIRE AND THE GROUND WIRE UP THROUGH THE NIPPLE THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST ON2. LE OF STEM INTO NOTCH OF RING THEN SCREW POLE ASSEMBLY TO END OF THE NIPPLE 3 DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG THE FIXTURE AT THE DESIRED HEIGHT USING PLIERS OPEN ONE END LINK OF CHAIN AND ATTACH TO THE CHAIN LOOP ON TOP OF THE FIXTURE REMOVE OR ADD CHAIN AS DESIRED AT THIS TIME LACE FIXTURE WIRE AND GROUND WIRE UP THROUGH EVERY OTHER LINK OF CHAIN TO SPREAD A LINK OF CHAIN USE OF PLIERS AND SCREWDRIVER AS SHOWN ABOVE BEING CAREFUL TO WRAP THE JAWS OF THE PLIERS WITH CLOTH TO PROTECT THE FINISH OF THE STOP COMPLETE INSTALLATION INSTRUCTIONS ON NEXT PAGE BEFORE CONTINUING TO FINAL ASSEMBLY FINAL ASSEMBLY 1 SLIDE CANDLE SLEEVE EACH 5 2 INSTALL A 60 MAXIMUM CANDELABRA BASE B BULB NOT INCLUDED INTO EACH SOCKET 3 ATTACHE 11 GLASS DROPS TO THE RINGS ON ARMS AND THE THE RING ON DISTRIBUTOR AS SHOWN 4 RESTORE POWER YOUR NEW FIXTURE IS NOW READY FOR USE AVAILABLE PARTS ARE 91735SHORB SHADE 91730CRYS GLASS DROP 91735ORB ASSEMBLY INSTRUCTIONS SUPPLY GROUND WIRE J OUTLET BOX WHITE BLACK SUPPLY WIRE SUPPLY WIRE CEILIN WIRE 5 BLACK OR 3 PCS FIXTURE WIRE WHITE OR RIBBED 8 52 SCREWS SUPPLIED WITH E E NIPPLE ROSSBAR IXTURE GROUND WIRE GROUND SCREW SCREW COLLAR NUT SCREW COLLAR
3. MODEL 917550RB PACKING DIAGRAM ANOPY CHAIN CHAIN LOOP AND OTHER PARTS POLE ASSEMBLY GLASS DROP 000 11 ____ 00000 STEM FIXTURE BODY amp 5 CANDLE SLEEVES ARDBOARD STYROFOAM 12 KGS WIRE 5 PCS IPPLE SCREW COLLAR NUT SCREW COLLAR LOOP HAIN LOOP POLE ASSEMBLY SHADE 91735SHORB REPLACEMENT PART SPIDER SLEEVE SOCKET O DISTRIBUTOR ARM 5 PCS GLASS DROP LASS DROP 91730CRY 11 PCS REPLACEMENT PART 4 06 2014 917 550 ASSEMBLY 5 5 READ AND SAVE THESE INSTRUCTIONS READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO ASSEMBLY THIS FIXTURE SHOULD TAKE APPROXIMATELY 15 MINUTES TO ASSEMBLE MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED TOOLS YOU WILL NEED THE FOLLOWING TOOLS OR LADDER SCREWDRIVER ADJUSTABLE WRENCH WIRE CUTTERS AND PLIERS UNPACK THE FIXTURE YOU SHOULD HAVE THE FOLLOWING PARTS IN THE PACKAGE CANOPY CHAIN POLE ASSEMBLY SHADE STEM FIXTURE BODY 5 CANDLE SLEEVES AND 11 GLASS DROPS TO PROTECT THE FINISH PLACE ALL PARTS ON A SOFT SURFACE MOUNTING HARDWARE PACKAGE SCREW COLLAR LOOP SCREW COLLAR NUT NUT NIPPLE 2 8 32 x 1 1 4 SCREWS CROSSBAR GREEN GROUND SCREW AND 3 WIRE CONNECTORS ASSEMBLY 1 SCREW STEM TO TOP OF DISTRIBUTOR 2 SLIDE NIPP
4. WIRE CONNECTORS PROVIDED CONNECT THE BLACK OR 5 FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE CROSSBAR THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTOR PROVIDED 4 TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX SPREAD THE ELECTRICAL SPLICES SO THAT THE BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE NEXT RAISE THE CANOPY TO THE CEILING AND SECURE IN PLACE BY SCREWING THE SCREW COLLAR NUT ONTO THE SCREW COLLAR LOOP 5 SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS 06 2014 917350 INSTALLATION
Download Pdf Manuals
Related Search