Home

GE 16547 Installation Guide

1. WARRANTY Jasco Products warrants that the fixture will be free of defects in material and workmanship for three years from date of purchase This warranty does not apply to the bulb This fixture warranty is limited to repair or replacement at Jasco s option Damage caused by modification abuse or misuse is not covered Jasco makes no other warranty express or implied of merchantability or fitness for a particular purpose In no event shall Jasco be liable for special incidental or consequential damages Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion of consequential damages so the above limitations may not applyto you This warranty gives you specific legal rights and you may also have other rights which vary based on your place of residence To obtain repair or replacement information under the terms of this warranty return the fixture and proof of purchase along with owner s name and address postage prepaid to Jasco Products Company LLC 10 E Memorial Road Oklahoma City OK 73114 Figure 1 Lens Diffuser front edge Cover Housing c Uy us LISTED Figure 2 Strain Relief g D Hot Black Supply Wire Ground G round Green or Neutral White g Supply Wire Copper Wires Hot Black Neutral White Fixture Wire Fixture Wire Figure 3 Figure 4 Wy Os CD Fluorescent Undercabin
2. with a screw driver 8 Insert the threaded end of the strain relief provided in the installation kit into the selected opening on the fixture Secure the strain relief by tightening the lock nut The lock nut should be tightened with a tool such as a pair of pliers to ensure the strain relief is properly grounded to the fixture 9 Install the conduit or armored cable to meet electrical codes Tighten the two screws on the strain relief connector to secure the wires 10 Connect the hot black AC supply wire s to the hot black wire s of the fixture Secure the connection with the wire nuts provided See Figure 2 11 Connect the white neutral AC supply wire s to the neutral white wire s of the fixture Secure the connection with the wire nuts provided See Figure 2 12 Connect the ground green or copper AC supply wire to the green or copper ground wire of the fixture Secure the connection with the wire nuts provided If your electrical system contains no grounding wire you should consult a qualified electrician before proceeding with the installation See Figure 2 13 Ensure that no bare wires are exposed after making the electrical connections 14 Arrange the wires inside the fixture and reattach the cover housing Tighten the screws or nuts to ensure that all the wires and connections are sealed properly inside the fixture without pinching any wires 15 Place the fixture in the location where it is to be mounted and
3. AWARNING Risk of electric shock Do not use in wet locations Use indoors only Turn power off before servicing see instructions Properly ground fixture Ensure that no bare wires are exposed outside the electrical connections Bulb may shatter and cause injury when broken Do not use excessive force when installing bulb Risk of burn Allow bulb to cool before handling INSTALLATION PROCEDURES 1 Consult a local licensed electrician or electrical contractor if you are not sure about the installation 2 Ensure that electricity is TURNED OFF at the main circuit breaker or fuse box DO NOT ATTEMPT TO INSTALL FIXTURE WITH THE POWER ON 3 Select a suitable dry mounting location for indoor use only Make sure the mounting surface is capable of supporting the fixture 4 Remove the lens diffuser by lightly pressing the front edge while lifting upwards The lens diffuser should pop out easily See Figure 1 5 Remove the bulb by grasping the ends of the bulb and rotating until the bulb becomes loose Pull straight out from the lamp holder and remove any cardboard inserts present Be careful not to drop the bulb See Figure 1 6 Remove the cover housing by unscrewing the two 2 nuts located behind the bulb Some models have screws located on the top and bottom of the fixture that hold the cover housing together 7 Choose a suitable knock out location from those provided on the fixture Remove the knock out
4. et Fixtures Direct Wire UCF003
5. mark the position of the keyholes with a pencil 16 It is recommended that a pilot hole 1 16 for soft wood 3 32 for hard woods be drilled in the mounting surface If the mounting surface requires the use of wall anchors drill a 1 8 pilot hole Install the plastic anchors provided in the installation kit 17 Drive the screws provided in the mounting hardware into the mounting surface until approximately 1 8 of space remains under the head of the screw See Figure 3 18 Align the keyholes in the fixture with the two screws and slide into place See Figure 4 19 Tighten the screws and install bulb and reinsert lens 20 Turn on the electricity at the circuit breaker or fuse box BULB REPLACEMENT INSTRUCTIONS See the label on the fixture for replacement bulb type information Do not replace with any other wattage of fluorescent bulb 1 Turn the fixture off and allow sufficient for bulb to cool before handling 2 Remove the lens diffuser by lightly pressing the front edge while lifting upwards The lens diffuser should pop out easily See Figure 1 3 Remove the bulb by grasping the ends of the bulb and rotating until the bulb becomes loose Pull straight out from the lamp holder Be careful not to drop the bulb See Figure 1 4 Grasp the replacement bulb in the same manner and reinsert into the lamp socket and turn tube until it is securely held in place Do not use excessive force when installing bulb 3 YEAR LIMITED FIXTURE

GE 16547 Installation Guide

Contents

Download Pdf Manuals

Related Search

Related Contents