TroposAir 88456 Instructions / Assembly
Contents
1. grease so that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for slope ceiling 12 This fan is reversible 13 This fan is not light kit adaptable 14 This fan is controlled by remote 15 This fan is suitable for indoor location use P1 Unpack and inspect fan carefully to be certain all contents are included Downrod Canopy Yoke cover LA P2 Hardware Bag For Mounting Plate Flat Washer x2 Spring Washer x2 Wood Screw x2 YN oO 0 YN 0 0 Machine Screw x2 For Wire Connection Wire Nut x 3 4a a 4a For Blade Installation Blade Screw x 10 one spare screw included TETTETETT FFFFF Paper Washer x 10 Qa 220282 Qo Go Ge Ge amp For Blade Balance Balanced slide x 1 BA Weight block 3G x 3 AAE Remote Battery Included amp Hardware Bag Wood Screw x2 S S Wire Nut x 5 4a 4 a a 4 WARNING blades should be at least 7 feet from floor Note 1 Note 2 Turn off power at breaker box to avoid possible Use metal outlet box suitable for fan support electrical shock Outlet box must support 35 Ibs min 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws i2. Owner s Manual roposAlir McCoy This instruction contains 6 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation and Hanging system installation Page 4 Wire connection Page 5 Blade installation Canopy installation Page 6 Remote astes Net weight Se 5 1 KGS Toll Free 1 855 676 7247 11 23 LBS WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning Two people recommended for fan installation 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 7 feet from floor when fan
3. ew heads are engaged in the narrow end of key holes Tighten both screws 4A Remove the bottom plate and flat washer at fan assembly 4B Insert Blades into Blade slots of Rotating Band Q Fasten blades onto motor assembly through rectangular hole by using the blade screws and paper washers provided from hardware bag 4C Attach flat washer and the bottom plate by screwing it clockwise onto center shaft Fan Assembly Fan Assembly Fan Assembly i Flat Washer Blade Screw 3 gt I A I amp Paper Washer 3 Bottom plate P5 5 REMOTE NOTE Make sure transmitter and receiver have the same code for fan operation LOW Fan low speed MED Fan middle speed HI Fan high speed OFF For SETTING Fan speed e Button for ON OFF Light NOTE This fan has no light so please disregard this light function 6 Turn on the power your fan is ready for operation P6
4. is in operation 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only Light kits that are not packed with the fan must be ETL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be made to work immediately after installation The bearings are adequately charged with
5. ncluded with the outlet box and washers from the hardware bag Outlet Box Mounting gt Bracket Y 1B Installing Downrod and Yoke Remove cross pin and cotter pin from downrod Insert downrod through canopy and yoke cover and feed motor lead wires through downrod Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod Pull down the yoke cover to cover yoke T y Q Wires gt f Downrod cross Pin Cotter Ping c0 Cotter Pin canopy Ct y ji nroa Jam Screw 2 Downrod Jam U gt Yoke cover A Screw 2 i Tightening 1C Hanging the fan Lift fan assembly onto mounting bracket Rotate fan so that the groove on the ball engages the ridge in the mounting bracket Ajquassy pouumoq x ja Mounting Bracket Mounting Bracket Ball Groove lt Fan Assembly 2 WIRE CONNECTION 2A Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts Note Wires from house may vary in color and may not include ground wire green After wiring is completed collect wires neatly inside hanging base White wire from house to white wire from receiver Black wire from house to black wire from receiver Ground wire from house to green wires from downrod and from mo
6. unting bracket White wire from fan to white wire from receiver Black wire from fan to black wire from receiver Secure with twist lock wire nuts Included From House From Receiver From Fan _ Motor N AC N Black ME _ a a ae ee ea a Motor L AC L from down rod Green for ground wire from mounting bracket 2B Setting code switches for transmitter Remote controls are tuned to operate together using 4 switches for 16 possible code combinations 1 Setting the code on the TRANSMITTER Remove battery cover Slide code switch randomly using a small screwdriver or ball point pen to slide each switch firmly up or down Install 9V DC battery Included Install battery cover on transmitter NOTE This fan has no light so please disregard this light function 2 Setting the code on the RECEIVER Slide code switches on the Receiver to be the SAME POSITIONS as set on your Transmitter Transmitter Code Switches Receiver Code Switches P4 2C Insert receiver into mounting bracket NOTE Do not squeeze all the wires while inserting the receiver into the mounting bracket Note Two screws are pre installed on mounting bracket for canopy installation Push up canopy until two screws pre screwed on mounting bracket are engaged with two key holes on canopy Rotate canopy slightly until two pre installed scr
Download Pdf Manuals
Related Search