TroposAir 88301 Installation Guide
Contents
1. 4 l If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan Ifthe fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 3 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side and the HOT wires on the other side 7 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 8 This fan is suitable for slope ceiling 9 This fan is light kit adaptable 10 This fan is suitable for indoor location use P1 Unpack and inspect fan carefully to be certain all contents are included Hardware Bag For Mounting Bracket Flat Washer x2 Spring Washer x2 Machine Scre2. Owner s Manual roposir The L A This instruction contains 6 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Hanging system installation Page 4 Wire connection and Canopy installation Page 4 5 Blade installation Page 6 Remote Net weight 6 0 KGS KIb LISTE Intertek 3110124 Toll Free 1 855 676 7247 WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout 13 2 LBS READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 tl To avoid possible electric shock be sure electricity is TURNED OFF at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 l Make sure that your installation site will not allow rotating fan blades to come in contact with any object BLADE SHOULD BE AT LEAST 7 FEET FROM FLOOR WHEN FAN IS IN OPERATION
3. g for step 4A two sides of blade for protecting blade from scratches Remove a part of the protection membrane on both Cnty cear Dings nave protec Honimemaname TTT E a aee a e e label or AE Membrane This side up 4A Blade end with This side up label should be attached to the TOP side of fan motor facing toward ceiling Make sure embossed spot on motor is properly aligned with positioning hole on blade Embossed Spot Positioning Hole Membrane 4C If present remove a part of the protection membrane on both sides of the other blade end and attach the blade end onto DOWN side of fan motor with blade screws and flat washers from hardware bag Membrane 4B Once aligned fasten the blade end onto TOP side of fan motor with blade screws from hardware bag CAUTION To avoid possible noise do not fully tighten the first blade screw while positioning Fasten both blade screws evenly after both screws are in place e Blade Screw Fan Assembly 4D After repeating steps 4A to 4C twice until all three blades are done remove the protection membrane from both sides of all three blades Turn on power at breaker box for remote setting P5 9 REMOTE INSTALLATION 5A Initial Settings Back side of Transmitter 1 Code setting on TRANSMITTER Remove battery cover FAN code setting There are 4 switches for 16 possible code combinations just in case your house has other fans installed with the
4. otate fan so that the groove on the ball engages T the ridge in the mounting bracket Ajquessy Bracket Mounting Bracket Ball Groove Fan Assembly 2 WIRE CONNECTION Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block Note Wires from house may vary in color and may not include ground wire green White wire from house to white wire from fan Black wire from house to black wire from fan Ground wire from house to green wire from downrod and from mounting bracket Secure with twist lock wire nuts Included After wiring is completed gently push wires into junction box with wire nuts pointing upward Outlet Box Wire Form House From House From Fan White F White AC N MOTOR N Black EEE N Black AC L MOTOR L Green y M A Green for ground wire a gowie Green from mounting bracket Note Two screws are pre installed on mounting bracket for canopy installation Push up canopy until two screws pre screwed on mounting bracket are engaged with two key holes on canopy 2 Rotate canopy slightly until two pre installed screw heads are engaged in the narrow end of key holes G Tighten both screws Key Hole 2 NOTE 1 NOTE 2 Please make sure blades are positioned with There may be two pieces of protection membrane on This side up label facing the ceilin
5. same codes You may change your code switches by using a small screwdriver or ball point pen to slide each code switch firmly up or down Note IF ONLY ONE FAN TO BE INSTALLED IN THE HOUSE YOU CAN SKIP THIS STEP 3 LIGHT On Off Dimming code setting This switch is to interchange light function while using incandescent bulbs Dimming or CFL bulbs On Off Dimming function Slide the code to D position for incandescent bulbs On Off function Slide the code to ON position for CFL bulbs 4 Install 12V 23AE battery x 1 pc The picture is showing for CFL bulbs W 12V 23AE Battery x 1 pc 5B SETTING before starting fan Pressing the button SET for 3 5 seconds till the fan operates which means this remote control is doing the setting Fan will operate clockwise for 2 5 minutes and anti clockwise for 2 5 minutes then stop automatically Totally 5 minutes for SETTING or 5C TRANSMITTER BUTTON II l 6 speeds from I Lowest Speed to VI Highest Speed Lowest Speed J ateyy VI Highest Speed Reversing Fan ON OFF switch Light switch two options 1 On Off for CFL bulbs 2 Dimming for incandescent bulbs Your fan is ready for operation P6
6. w x2 Wood Screw x2 For Wire Connection Wire Nut x 3 a a y For Blade Installation Blade Screw x 13 one spare screw included Remote Battery Included t Hardware Bag Wood Screw x2 S WARNING blades should be at least 7 feet from floor Note 1 Note 2 Note 3 Turn off power at breaker Use metal outlet box suitable CAUTION box to avoid possible for fan support Do not fold blades with heavy electrical shock Outlet box must support 35 Ibs min pressure from two sides It may cause blades to crack O O 1 HANGING SYSTEM INSTALLATION 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers from the hardware bag Outlet nak sb Mounting Bracket 1B Installing Downrod and Yoke Remove cross pin and cotter pin from downrod 2 Insert downrod through canopy and yoke cover and feed motor lead wires through downrod 3 Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod 6 Pull down the yoke cover to cover yoke 2 Wires Downrod Cross Pin 4 Cotter Ping Co Canopy li 2 24 Downrod Jam Loosening lt amp 5 Screw 2 Yoke cover pL ESD os Tightening 1C Hanging the fan Lift fan assembly onto mounting bracket R
Download Pdf Manuals
Related Search