Hampton Bay 12112-029 Installation Guide
Contents
1. 13 Center _ 14 Fixture Decorative Column Loop x4 B10 Bulb 60W max not included x12 15 Decorative Loop fis Screw x8 S do Socket O O g Fixture Body QD 16 Decorative Bottom Hub g _ 17 Bottom Nipple _ 18 Hex Nut 19 Decorative Finial Page 52. TROUBLESHOOTING i al Possible Cause Corrective Action 1 Bulb is burned out 1 Replace light bulb Bulb will not light 2 Switch is off 2 Make sure switch is on 3 Faulty wire connection 3 Check wiring Crossed wires or power wire is grounding out Fuse blows or circuit breaker trips when light is turned on Check wire connections PRODUCT MAINTENANCE 1 To clean the outside of the lamp use a dry or slightly dampened clean cloth use clean water never a solvent to wipe the shade and surface of the lamp 2 To clean the inside of the fixture first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box Next use a dry or slightly dampened clean cloth use clean water never a solvent to wipe the inside shade and interior surface of the fixture 3 Do not use any cleaners with chemicals solvents or harsh abrasives Use only a dry soft cloth to dust or wipe carefully LIMITED WARRANTY The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five 5 years from date of purchase This warranty applies only to the original consumer purchaser and only to products used in normal use and service If this product is found to be defective the manufacturer s only obligation and your exclusive remedy is the repair or replacement of the product at the manufacturer s discretion provided that the product has not been dam
3. aged through misuse abuse accident modifications alterations neglect or mishandling This warranty shall not apply to any product that is found to have been improperly installed set up or used in any way not in accordance with the instructions supplied with the product This warranty shall not apply to a failure of the product as a result of an accident misuse abuse negligence alteration or faulty installation or any other failure not relating to faulty material or workmanship This warranty shall not apply to the finish on any portion of the product such as surface and or weathering as this is considered normal wear and tear The manufacturer does not warrant and specially disclaims any warranty whether express or implied of fitness for a particular purpose other than the warranty contained herein The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage including but not limited to any labor expense costs involved in the replacement or repair of said product Page 8 INSTRUCTION MANUAL INTERIOR 12 LIGHT CHANDELIER GLASGOW HOME DEPOT SKU 886 501 S O 127 408 UPC 773546175456 BLACK FINISH l MAL amp f O _ So Gl LA Page 1 Thank you for purchasing this Hampton Bay interior decorative lighting This product has been manufactured with the highest standards of safety and quality FEATURES An assiduous parity of heavy i
4. oop 9 Canopy 3 Crossbar ql 10 Loop Ring INSTALLATION INSTRUCTION Turn off power at main fuse box 2 Install cross bar 3 assembly complete with nipple 7 and canopy loop 8 to junction box 1 as one complete assembly w Remove loop ring 10 from canopy loop 8 Slip canopy 9 over loop 8 and secure by fastening loop ring 10 Adjust the height of the nipple 7 so canopy 9 will sit flat against ceiling and tighten lock nut 6 against cross bar 3 D Remove loop ring 10 and canopy 9 from ceiling Nn Hold chandelier up against canopy loop 8 with chain and adjust to desired height Remove excess chain a Before tightening chain onto canopy loop 8 weave chandelier wire through every second link 7 Let the canopy loop ring 10 slip to the bottom of chain Repeat this step for canopy 9 8 Secure chain onto canopy loop 8 9 Weave wire through the canopy loop 8 and into junction box 1 10 Install both ground wires of chandelier one from the canopy 9 and one from the fixture to ground screw 5 or ground wire of junction box 1 or ground screw 5 on cross bar 3 See Fig 1 11 Connect black wire of power supply to the smooth side of the wire flexible cord from the chandelier and connect white wire of power supply to the ribbed side of the wire from the chandelier See Fig 1 NOTE Always use wire nuts 2 or marrettes included to connect wire
5. ronwork with delicate composition are the origin of this benevolent classic QUESTIONS PROBLEMS MISSING PARTS Before returning to your local Home Depot please call our Customer Service Team at 1 877 527 0313 or visit www homedepot com Please reference your SKU 886 501 UPC 773546175456 CAUTION 1 Before starting installation of this fixture or removal of a previous fixture disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box 2 CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS 3 If you have any non electrical questions about this fixture please contact our Customer Service Team at 1 877 527 0313 or visit www homedepot com Please reference your SKU 886 501 or UPC 773546175456 4 Keep your receipt and these Instructions for Proof of Purchase Page 2 INSTALLATION 1 Junction Box not included Ground Wire Black Wire 5 Ground Screw 3 Cross Bar 6 Lock Nut 7 Nipple l 4 Outlet Box Screw x2 9 Canopy co N l WHITE OR RIBBED WHITE OR RIBBED FROM HOUSE FROM FIXTURE l l l BLACK OR RED WIRE BLACK OR SMOOTH l l l FROM HOUSE FROM FIXTURE GROUND WIRE FROM HOUSE GROUND WIRE FROM FIXTURE Page 7 PARTS ADDITIONAL PART FOR INSTALLATION included iN 2 Wire Nut x3 4 Outlet Box 5 Ground Screw 6 Lock Nut Screws x2 DS ce 7 Nipple 8 Canopy L
6. s and push all excess wire and connections back into junction box 1 See Fig 1 12 Lift canopy 9 up to ceiling covering junction box 1 and secure by using canopy loop ring 10 Page 6 TOOLS REQUIRED FOR ASSEMBLY amp INSTALLATION not included Wire Strippers Wire Cutters Flathead Safety goggles Screwdriver Phillips Electrical Tape Ladder Screwdriver B10 Bulb 60W max not included x12 ADDITIONAL PARTS FOR ASSEMBLY included 11 Chain Loop 13 Center Column 14 Fixture Decorative 15 Decorative Loop x4 Loop Screw x8 QD ca v 16 Decorative 17 Bottom Nipple 18 Hex Nut 19 Decorative Bottom Hub Finial Page 3 ASSEMBLY INSTRUCTIONS 1 Carefully unpack the fixture lay out all parts on a clean surface 2 Install chain loop 11 on center column 13 3 Tighten column 13 onto the central hub of the fixture body 4 Place decorative loop 14 onto the center column hooks 12 then secure to fixture body with decorative loop screws 15 5 Install bottom decorative hub 16 onto the base of the fixture body Secure with bottom nipple 17 then tighten with hex nut 18 6 Complete bottom assembly by tightening decorative finial 19 onto bottom nipple 17 BULB INSTALLATION 1 Install B10 Bulb 60W max not included Page 4 ASSEMBLY et RSS Mey asy Se 10 Loop Ring 11 Chain Loop a Center Column Hooks ARS Y
Download Pdf Manuals
Related Search