TroposAir 88500 Instructions / Assembly
Contents
1. Blade x5 P2 WARNING blades should be at least 7 feet from floor Note 1 Note 2 Turn off power at breaker Use metal outlet box suitable box to avoid possible for fan support electrical shock Outlet box must support 35 Ibs min 1 HANGING SYSTEM INSTALLATION 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers from the hardware bag omen ik lf S 2 ne 2 Mounting A Bracket 1B Installing Downrod and Yoke Remove cross pin and cotter pin from downrod Insert downrod through canopy and yoke cover and feed motor lead wires amp safety cable through downrod Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod Pull down the yoke cover to cover yoke Wires Downrod cross Pin Cotter Ping lt 0 Canopy lt O Downrod Jam Screw 2 Loosening Yoke cover j l q Ajqwu ssy pojumoq P3 1C Attaching the Up Glass Assembly onto Fan Assembly Place the up glass assembly onto grill of fan assembly Secure the up glass assembly with 3 spring clips and 3 glass screws provi2. Owner s Manua roposAlir Excalibur This instruction contains 6 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation and Hanging system installation Page 4 Wire connection Page 5 Canopy and Blade installation Page 6 Switch housing and Pull Chain Knob installation Net weight 12 5 KGS 27 5 LBS Toll Free 1 855 676 7247 WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 7 fee
3. light kit Note There are two Pull Chain Knobs provided from hardware bag For FAN SPEED 3 speeds High Med Low Connect one pull chain knob to the pull chain switch marked SPEED For UP LIGHT On Off Connect one pull chain knob to the pull chain switch marked LIGHT AA LIGHT Light Pull Chain lt Pull Chain Knob 7 Turn on the power at breaker box your fan is ready for operation P6
4. ded from hardware bag onto grill Gently install 4 incandescent bulbs 15W provided from box to lamp holders Glass Screws 3 Spring Clip 3 Z Incandescent Assembly 4 Bulb 15W 4 1D Hanging the fan Lift fan assembly onto mounting bracket Rotate fan so that the groove on the ball engages the ridge in the mounting bracket Mounting Bracket Mounting Bracket 2A Attaching safety cable to ceiling joist Use wood screw spring washer and flat washer from hardware bag Pass wood screw through closed loop of safety cable Secure wood screw to ceiling joist through any available slot on mounting bracket Make sure safety cable has been tightened securely CAUTION THE WOOD SCREW AND ITS SUPPORT MUST BE ABLE TO FULLY SUPPORT THE WEIGHT OF AT LEAST 100 LBS Safety cable Flat Washer Spring Washer Wood Screw Safety cable 4 Mounting Bracket 2B Making wire connections Follow diagram below and make sure that all exposed wires are secured inside wire nuts Note Wires from house may vary in color and may not include ground wire green After wiring is completed gently push wires into junction box with nuts pointing upward Wire Form House From House From Fan Outlet eae White gt White AC N Motor N a ee aa Biack a lt P one Black Blue Orange for light kit f
5. ly after installation The bearings are adequately charged with grease so that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for slope ceiling 12 This fan is reversible 13 This fan is light kit adaptable 14 This fan is remote adaptable 15 This fan is suitable for indoor use 16 This fan uses a 3 4 diameter nominal downrod P1 Unpack and inspect fan carefully to be certain all contents are included Hardware Bag For Mounting Bracket Flat Washerx Spring Washer x3 gt 1 l Machine Screw x2 Wood Screw x3 Mounting Bracket Downrod Assembly For Up Glass Assembly Spring Clip x3 Glass Screw x3 Canopy Cao nee 6 Sey For Wire Connection Yoke cover a WireNutx4 Ac NOVA ie For Blade Installation A r gt 4 a Blade Screw x 16 one spare screw included KANGAN H PPPPPPP P Up Glass Assembly NR EV NG rTrPrPPPRPRRRSF 3 x T B j Paper Washer x 16 one spare washer included Kee D eooocooaocand Incandescent Bulb Motor Screw x 11 one spare screw included Safety cable a EEA oocoocoococnd amp Wires 15W x4 O GB GB O O O GC For Fan and Light Pull Chain Knob x2 e For Blade Balance Balancing slide x 1 A Weight block 36 x3 DDD Fan Assembly
6. or up light kit Green from downrod Green l Green for ground wire from mounting bracket Secure with twist lock wire nuts Included Note Two screws are pre installed on mounting bracket for canopy installation Push up the Canopy until the two screws on mounting bracket are engaged with key holes in canopy Rotate the canopy slightly until the two screw heads are in the narrow end of the key holes Tighten both screws screw 2 4 BLADE INSTALLATION Attach blade to blade holder with 3 blade screws and 3 paper washers provided from hardware bag Make sure all screws are firmly tightened Remove 3 motor stoppers by removing screws Secure Blade Assembly to the motor with 2 motor screws provided from hardware bag NOTE To prevent wobble do not bend blade or blade holder Blade Screw ae amp Paper Washer 3 E i Q Key Hole 2 Blade Assembly amp lt Motor Screw 2 1 P5 5 SWITCH HOUSING INSTALLATION amp WIRE CONNECTION Connect 9 pin terminal from fan assembly with 9 pin terminal from switch housing Remove 3 set screws from switch housing cover and keep them for Step Lift the switch housing up in place Fasten switch housing and the cover together with 3 set screws removed from Step Switch Housin Fan Assembly Screw a pane ee C thy Note For connecting light wires while adapting
7. t from floor when fan is in operation 4 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL ETL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be made to work immediate
Download Pdf Manuals
Related Search