Sea Gull Lighting 8871-12 Installation Guide
Contents
1. place with small cap nuts F STEP 3 Install lamps STEP 4 Thread diffuser retaining screws X into holes at top of fixture Raise diffuser B and finger tighten retaining screws X Over tightening retaining screws X may cause diffuser B to break STEP 5 Snap on wire cage G CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts2. INSTALLATION AND SAFETY INSTRUCTIONS Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully Proper wiring is essential for the safe operation of this fixture To reduce the risk of electrical shock provide a watertight seal between the fixture and the mounting surface by using a silicone or similar caulking Save these instructions GREEN GROUNDING SCREW G MOUNTING OUTLET BOX OUTLET BOX SCREWS MOUNTING SCREWS I FIGURE 1 GROUNDING amp MOUNTING BAR LOCK UP OUTLET BOX SCREWS OUTLET MOUNTING SCREWS Till lt F CROSS MOUNTING BAR D WIRE CONNECTOR gt FIGURE 2 NOT SUPPLIED Carefully remove the fixture from the carton and check that all parts are included as shown in Figures 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture NOTE This glass is handcrafted the slig
3. e end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw L is to be inserted into the hole with two raised dimples provided on the cross mounting bar B Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw L on the cross mounting bar B if uninsulated ground wire is on the cross mounting bar B connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied See Figure 2 NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY STEP 1 Make sure no bare wires can be seen outside wire connectors After wires are connected tuck them carefully inside outlet box STEP 2 Position backplate E over mounting screws l Secure in
4. ht imperfections in the glass add to the authenticity of the fixture igs os ZO 2 7 RETAINING SCREWS X DIFFUSER B WIRE CAGE G NOT INCLUDED sea gull lighting Installation And Safety Instruction HC 571 Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture 102607 Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 571 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Insert fixture mounting screws I in threaded holes of cross mounting bar B Run fixture mounting screws I all the way down to the heads STEP 2 Place cross mounting bar B against outlet box not supplied and fasten cross mounting bar B to outlet box with outlet box screws not supplied Be sure the mounting screws l are perfectly horizontal so fixture hangs straight STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wir
Download Pdf Manuals
Related Search