Worldwide Lighting W33141C10-CL Instructions / Assembly
Contents
1. damage or smudging on the crystals Frame Assembly Diagragram WV V WAVY LLAS CANOPY INSTALLATION INSTRUCTIONS MAKE SURE POWER IS DISCONNECTED Attach washer to supporting member in ceiling sufficient to support weight of fixture Slip screw collar prismatic cover and metal canopy over chain Determine the suspension length of the fixture and cut chain if necessary Use two connecting links to attach chain to chandelier loop and ceiling loop Insert stem wire through chain and ceiling loop Connect wires Fixture MUST be grounded Check distance from ceiling to loop to assure canopy assembly will be flush against ceiling Attach canopy to ceiling with screw collar WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb GU10 35W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to li2. W 33141C10 GT D10 H6 L3 We are dedicated to providing the finest quality crystal chandelier for our customers Our master craftsmen and designer pride themselves on their attention to detail prompt efficient service 1S our priority Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions carefully and thoroughly If you have any questions please fell free to call our toll free DHANDELIER HOTLINE AT 1 890 411 8999 ON Crystal Dressing Instructions CANOPY PARTS LIST When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any Existing Electrical Box damage or smudging on the crystals Crossbar Crossbar Screws x 2 not srpplied ee Metal plate Wire Connector Shrinkable tube Ground Wire Cable tie CANOPY INSTALLATION DIAGRAM Frame Parts List i 03 Metal Finial 01 Crossbar 02 Lamp Body WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion betwee
3. n parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only 7 Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation Worldwide lighting shall not be responsible for unprofessional wiring Crystal Dressing Diagram When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any
4. ossbar 02 with crossbar bracket 04 3 Make sure the positive and negative charges of wire and lamp body match correctly screw the connect point with the junction cap 4 Make sure the main wire is enough long and keep the rest wire in the 4 J box 5 As the crystal pressing instruction hang the crystal parts The end
5. ve wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only T Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation Elegant lighting shall not be responsible for unprofessional wiring Frame Assembly Instructions Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and remains off until installation is complete please note that each part has been assigned a number please proceed in a numerical order 1 Fix the crossbar 02 with chain 01 or junction box 2 Fix the lamp body 03 on the cr
Download Pdf Manuals
Related Search