Sea Gull Lighting 8588-12 Installation Guide
Contents
1. WET LOCATION NOTE FOR FIXTURES LABELED FOR WET LOCATION AND USED OUTDOORS CAUTION To reduce the risk of electrical shock provide a watertight seal between the fixture and the mounting surface by using a silicone or similar caulking2. STALLATION HC 269 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Using outlet box screws not supplied fasten mounting bar D to outlet box through slots in mounting bar D STEP 2 Thread nut E onto nipple F so that 5 threads are exposed above nut E Thread that end of the nipple F into mounting bar D and tighten nut E against mounting bar D STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A GROUP B CONNECT TO BLACK HOUSE WIRE CONNECT TO WHITE HOUSE WIRE BLACK WHITE PARALLEL WIRE SQUARE amp RIDGED a PARALLEL WIRE ROUND amp SMOOTH a O Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connector If you can remove the wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from g
3. a Installation And Safety Instructions HC 269 PRA ull ii iiri Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to i ft j this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM 070208 IMPORTANT SAFETY INSTRUCTIONS BEFORE YOU BEGIN e Be sure the electricity to the system you are working on is turned Carefully remove the fixture from the carton and check that all parts off either the fuse removed or the circuit breaker set at off are included as shown in Figure 1 Be careful not to misplace any of e Use of other manufacturers components will void warranty listing the screws or parts which are needed to install this fixture and create a potential safety hazard e If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully Save these instructions CAUTION Fixtures with photocells should be mounted at least 48 from all sides to avoid reflection of light back onto photocell causing the photocell to malfunction or flicker IF SUPPLY WIRES ARE LOCATED WITHIN 3 OF BALLAST USE WIRE RATED FOR AT LEAST 90 C WIRE MOUNTING NIPPLE F CONNECTORS BAR D ROOF L SOCKET M CAP NUT H OUTLET pum BOX SCREWS GREEN GROUNDING SCREW G CANOPY I FIGURE 1 NOT INCLUDED IN
4. roup B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw G is to be inserted into the hole with two raised dimples provided on the mounting bar D Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw G on the mounting bar D if uninsulated wire is on the mounting bar D connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 Make sure no bare wires can be seen outside wire connectors STEP 2 After wires are connected tuck them carefully inside outlet box Push the fixture firmly over the mounting nipple F and against the wall Secure canopy l in place by threading cap nut H onto nipple F STEP 3 Install lamps CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search