Worldwide Lighting W83041C22 Instructions / Assembly
Contents
1. W 83041022 D22 H26 L11 We are dedicated to providing the finest quality crystal chandelier for our customers Our master craftsmen and designer pride themselves on their attention to detail prompt efficient service is our priority Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions carefully and thoroughly If you have any questions please fell free to call our toll free DHANDELIER HOTLINE AT 1 855 411 8999 C US Crystal Dressing Instructions CANOPY PARTS LIST When dressing the chandelier with the crystals please remember Existing Electrical Box to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals Crossbar Screws Crossbar Screws x 2 not srpplied 14mmX14 14mmX13 B C D i AOmmX1 i 40mmX 1 AOmmX1 40mmX1 Decorative frame A eee Lanp pole 14mmX7 14mmX3 14mmX4 DE 14mmX9 14mmX11 14mmX6 14mmX1 2 Canopy 40mmX1 40mmX1 x Pe se F Chains 6 H Wire Connector Shrinkable tube Cable tie Ground Wire AOmmX1 40mmX1 40mmX1 L 14mmX1 14mmX2 14mmX9 14mmX1 CANOPY INSTALLATION DIAGRAM Frame Parts List 01 Lamp Body WARNING Crystal Dressing Diagram CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation When dressing the chandelier WARNING ao2. ed NY x 7 a BO electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that a7 eo CA the elecrtrical supply to the chandellier is turned off at the ne IN eo main fuse or circuit breaker before doing any installation Worldwide s D lighting shall not be responsible for unprofessional wiring B Frame Assembly Diagragram CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefuly Before you proceed to install make sure that the power supply is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order Existing Electrical Box Crossbar Crossbar Screws Metal Plate Crossbar Bracket Neutral Conductor Hot Wire Junction Caps Ground Wire J Wire LD Le CI WV WY Fa mm HO TE O w IT Sy Attach the Crossbar B to the existing electrical box A using the two crossbar screws E which are not supplied and should already be in your box ON ANZN AA VAN NYY WO RR LVN ZY ANSAN WAZ WAAAY AMAZAN VAAN rh NYY AN SA AY WAN We ANAAN NVVUW WAY ways ZEN ASS VAAN WWW VA 4 os JN ARAN ANA NVVW WO Yay VAAN ANA a NAVAUE EK SY ANSIN WAZA EK Cy LNA ANSAN TAVAYA WAY Sv MAAN AAA NW WAY 2 WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The m
3. etal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only T Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electr
4. ical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation World wide lighting shall not be responsible for unprofessional wiring Frame Assembly Instructions Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and remains off until installation is complete please note that each part has been assigned a number please proceed in a numerical order Install Decorative frame 02 and Lamp pole 03 on lamp body 01 Install Crossbar with J Box and then Fixed the Canopy 05 Join the lamp body 01 and crossbar 04 with chains 06 Make sure the main wire is enough long and keep the rest wire in the 4 J box As the crystal pressing instruction hang the crystal parts Install lighting Source
5. with the crystals please remember to wear either rubber or cotton After passing the main eiectrical wire through the 10mm pipe gloves So as to prevent any and connecting the pipe to the main body top connector place damage or smudging on the crystals all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only T Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected AN 9 Firmness must be secured when installing ceiling Oey o tube chain pipe and other connecting parts EN RY 10 Care should be taken to avoid damage when installing glass ASIN Ry MOSIA NA Wy A parts WOO AN Wy i i G RUN 11 A11 electrical components must be installed by a licens
Download Pdf Manuals
Related Search