Worldwide Lighting W83095C23-SM Instructions / Assembly
Contents
1. NING ff with the crvstals please remember i a to wear either rubber or cotton L gloves So as to prevent anv After passing the main electrical wire through the 10mm pipe and damage or smudging on the crystals connecting the pipe to the top main body connector place all remaining pieces as shown in numerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts CAUTION Rated 110v 130v 60Hz bulb E12 40W maximum 2 Take care to avoid damage to the surface of lighting and wire Wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to the white or blue wire Then connect to the neutral wire and double colored or bare copper wire to the ground wire 4 Never install lighting on damp ceiling The room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas Clean with soft cloth only 6 Installation must be carried out by qualified electrician only 7 Disconnect the power before installing cleaning or replacing the lamp 8 Never cover the lighting when power is connected 9 Fixture must be secured when installing the ceiling tube chain pipe and other connecting parts 10 Take care to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code It must be in the appropriate local electrica2. W 83095C23 CL D23 H25 L4 We are dedicated to providing the finest quality of crystal chandeliers for our customers Our master craftsman and designers pay their full attention to detail prompt and efficient service Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions thoroughly If you have any questions please feel free to call our toll free chandelier hotline at 1 859 411 8999 C US Crvstal Dressing Instructions CANOPV PARTS LIST When dressing the chandelier with the crystals please remember Existing Electrical Box to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals Crossbar Screws Crossbar Screws x 2 not srpplied Canopy Chains 14mmX1 L 14mmX2 ane g 3 14 x15 285mm Glass Bowl RIRS 32323225252900 28S Glass crafts D kd 14mmX2 14mmX5 Wire Connector Shrinkable tube 12strings 14 x14 272mm i Cable tie Ground Wire CANOPV INSTALLATION DIAGRAM Frame Parts List W83095C23 02 Crossbar PROPS SSIS QR ORK 03 Canopy ETD 04 Chains WY 05 Glass Bowl b42H5mm SRBBA 21200026 g 30H2mm 01 Lamp Body WARNING Crystal Dressing Diagram CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please have extreme caution when unpacking and installing When dressing the chandelier WAR
3. g glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code It must be in the appropriate local electrical codes Make sure that the electrical supply to the chandelier is turned off at the main fuse or circuit breaker before doing any installation Worldwide lighting is not responsible for unprofessional wiring blue wire Then connect to the neutral wire and double colored Lamp Body 02 match
4. l codes Make sure that the electrical supply to the chandelier is turned off at the main fuse or circuit breaker before doing any installation Worldwide lighting is not responsible for unprofessional wiring Frame Assemblv Diagragram CANOPV INSTALLATION INSTRUCTIONS Please read all instructions carefulv Before vou proceed to install make sure that the power supplv is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order A Existing Electrical Box B Crossbar C Crossbar Screws D Metal Plate E Crossbar Bracket F Neutral Conductor G Hot Wire H Junction Caps I Ground Wire J Wire WWW jik BE VS Attach the Crossbar B to the existing electrical box A using the two crossbar screws E which are not supplied and should already be in your box En wy MAI tp naw y IN 18 me kB WARNING Frame Assembly Instructions CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please have extreme caution when unpacking and installing Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and WARNING 1 1 remains off until installation is complete eee please note that each part has been assigned a number After passing the main electrical wire through the 10mm pipe and please p
5. roceed in a numerical order connecting the pipe to the top main body connector place all remaining pieces as shown in numerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts CAUTION Rated 110v 130v 60Hz bulb E12 40W maximum 2 Take care to avoid damage to the surface of lighting and wire Wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to the white or Assembly Lamp Body 01 Install Crossbar with J Box and then Fixed the Canopy 03 Join the Lamp Body 01 and crossbar 02 with Chains 04 Make sure the positive and negative charges of wire and correctly screw the connect point or bare copper wire to the ground wire with the junction cap 4 Never install lighting on damp ceiling The room should be Make sure the main wire is enough long and keep the rest dry and well ventilated wire in the 4 J box 5 Keep lighting away from acid alkali and other corrosive As the ervstal pressing instruction hang the ervstal chemical or gas Clean with soft cloth only Leaner lighting S 6 Installation must be carried out by qualified electrician Me IGGIB ONES only a Disconnect the power before installing cleaning or replacing the lamp 8 Never cover the lighting when power is connected 9 Fixture must be secured when installing the ceiling tube chain pipe and other connecting parts 10 Take care to avoid damage when installin
Download Pdf Manuals
Related Search