Sea Gull Lighting 8607-12 Installation Guide
Contents
1. S lt LOWER SCREW FOR ANGLE lt SHADE G CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts WET LOCATION NOTE FOR FIXTURES LABELED FOR WET LOCATION AND USED OUTDOORS CAUTION To reduce the risk of electrical shock provide a watertight seal between the fixture and the mounting surface by using a silicone or similar caulking2. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully NOTE Read the instructions carefully If you are unclear as to how to proceed consult a qualified electrician NOTE Illustration is only intended for easy identification of parts and is in no way a representation of your particular fixture Your fixture may not use every part shown in illustration OUTLET BOX WIRE CONNECTOR SWIVEL SCREW A FOR SHADE ANGLE NIPPLE F FIGURE 1 NOT SUPPLIED ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX GREEN GROUNDING SCREW G NIPPLE E MOUNTING BAR D GROUND WIRE WIRE CONNECTORS NOT INCLUDED CAUTION ONLY AIM SHADE BELOW HORIZONTAL FIGURE 2 s6a gull lighting Installation And Safety Instruction HC 412 100101 Fill In I
3. ector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw is to be inserted into the hole with two raised dimples provided on the mounting bar Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw on the mounting bar NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connect tuck them carefully inside outlet box Raise the canopy B firmly over the mounting nipple F and against the wall Secure in place with cap nut J STEP 2 IF APPLICABLE Install gasket through lamp base STEP 3 Install lamps If your fixture has two adjustment screws For swivel adjustment Slightly loosen upper and lower swivel tension screws Angle and rotate shade G to desired position tighten screws See Fig 3 If applicable Q lt UPPER SCREW FOR ROTATION
4. tem Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 412 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX Secure mounting bar D to outlet box with outlet box screws not supplied Thread nut E on nipple F so that 3 threads are exposed above nut E Thread nipple F into mounting bar D and secure with nut E A Take note of the color of the wire s on your fixture Identify which group your fixture wire s fall into and connect the wire s according to the directions below F GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE o PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED WHITE OR GREY WITH TRACER h YY SS BROWN GOLD OR BLACK WITHOUT TRACER WHITE OR GREY WITHOUT TRACER BROWN GOLD OR BLACK WITH TRACER Ss SS SS SE SS NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the conn
Download Pdf Manuals
Related Search