Sea Gull Lighting 8834-12 Installation Guide
Contents
1. Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 526 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX Insert fixture mounting screws I in threaded holes of universal mounting bar J Run screws all the way down to the heads A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below tf GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE Berack whe PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED o WHITE OR GREY WITH TRACER a NTN BROWN GOLD OR BLACK WITHOUT TRACER WHITE OR GREY WITHOUT TRACER BROWN GOLD OR BLACK WITH TRACER SS SE SEE SN Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection2. pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
3. E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 3 GROUNDING INSTRUCTIONS The green grounding screw L is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw L on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside the outlet box Position fixture pan D over mounting screws l1 and secure in place with cap nuts N STEP 2 Install lamps STEP 3 Raise glass P rubber washer if applicable to center pipe secure with finial F CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring
4. INSTALLATION AND SAFETY INSTRUCTIONS WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU Carefully remove the fixture from the carton and check that all parts ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED are included as shown in figure 1 and 2 Be careful not to misplace OR THE CIRCUIT BREAKER SET AT OFF any of the screws or parts which are needed to install this fixture WARNING FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE WARNING ONLY THESE WARNINGS ARE PROVIDED ON THE U L LABEL You don t neeg special toos to install mg fixture Be sure to follow AND ON THE FIXTURE CARTON the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type i i p WARNING RISK OF FIRE MOST DWELLINGS nm Hea suite sy Kyou an uea da bion BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED to proceed consult a qualified electrician 60 C a eT GROUNDING amp UNIVERSAL MOUNTING BAR LOCK UP FIG 2 OUTLET BOX UNIVERSAL GREEN OUTLET BOX MOUNTING GROUNDING SCREWS K SCREW L WIRE CONNECTORS MOUNTING SCREWS I FIXTURE MOUNTING SCREWS I CAP 3 Zar NUTS P ae oy UNIVERSAL K MOUNTING BAR J FINIAL F FIGURE 1 NOT INCLUDED sea gull lighting Installation And Safety Instruction HC 526 040301 Lineart shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture
Download Pdf Manuals
Related Search