Sea Gull Lighting 8202-12 Installation Guide
Contents
1. ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts2. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician NOTE Proper wiring is essential for the safe operation of this fixture FIG 1 bs FINIAL A TOP ASSEMBLY B S lt SCREWS C Pa CAGE D _ 0 N W SCREWS gt ye lo lt FITTER E ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture Attach finial A to top assembly B of fixture if not factory installed CAUTION Fixtures with photo cells should be mounted at least 48 from all sides to avoid reflection of light back onto Photo cell causing the Photo cell to malfunction or flicker NOTE Your handcrafted solid brass lighting fixture has been coated with a durable baked on acrylic lacquer which gives maximum protection against the weather In time howe
3. p the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box Do Not twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 2 GROUND INSTRUCTIONS Connect the ground wire from the fixture bare metal or green insulated wire to the ground wire from the power supply bare metal or green insulated wire using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES STEP 3 Slide fitter E onto post Secure in place FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors NOTE IF GLASS PANELS ARE NOT INSTALLED PLEASE FOLLOW THIS STEP PLACE BOTTOM EDGE OF GLASS INTO CHANNEL BEND TABS OVER EDGE TO SECURE IN PLACE STEP 1 Install lamp STEP 2 Place top assembly B onto cage D and secure in place with screws C CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper
4. ver the brightness of the brass will tarnish giving way to an authentic old world brass finish NOTE To keep your solid polished brass fixture looking new for years to come regularly apply a good quality non abrasive car wax to all metal surfaces giving the fixture an extra protective coating WARNING NOTE DO NOT INSTALL ON A POST OR A POLE THAT RESULTS IN A VERTICAL RISE OF 25 FEET OR HIGHER NOTE This glass is handcrafted the slight imperfections in the glass add to the authenticity of the fixture NOTE Be sure that all sections of top finial are securely tightened to prevent water seepage into the fixture ITEM Fill in item number located on carton and file this sheet for future reference HC 234 012405 INSTALLATION HC 234 STEP 1 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED a S gt WHITE OR GREY WITHOUT TRACER WHITE OR GREY WITH TRACER h ee ee BROWN GOLD OR BLACK WITHOUT BROWN GOLD OR BLACK WITH TRACER ER ar NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires gras
Download Pdf Manuals
Related Search