Sea Gull Lighting 75061-962 Installation Guide
Contents
1. lt CONNECTORS MOUNTING O BAR A ap MOUNTING SCREWS I OUTLET BOX SCREWS GREEN GROUNDING SCREW D NOT INCLUDED FIGURE 2 WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY MOUNT TO OUTLET BOX OR SUPPORTING SYSTEM ABLE TO SUPPORT THE WEIGHT OF THE FIXTURE sea gull lighting Installation And Safety Instruction HC 344 030700 Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 344 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX Thread fixture mounting screws I in through top of mounting bar A raised side is on top as illustrated Run screw threads all the way down to the heads Secure mounting bar A to outlet box with outlet box screws not supplied A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE Back tc ititi C PARALLEL WIRE ROUND amp SMOOTH f PARALLEL WIRE SQUARE amp RIDGED WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER ee BRONN GOLD OR BLACK WITHOUT BROWN GOLD OR BLACK WITH TRACER Ee E SN Note2. When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A If uninsulated wire is on the mounting bar A connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the pr
3. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in Figures 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture NOT SUPPLIED FIGURE 1 OUTLET BOX WIRE CONNECTORS MOUNTING SCREWS I SOCKET ASSEMBLY U FIXTURE RING Q HICKEY W LOCK WASHER V NUT U DIFFUSER R NIPPLE P RUBBER WASHER _ DECORATIVE AND NUT CUP 0 fa ee FINIAL N STEP 1 if applicable Thread nut U onto nipple P so that five threads are shown above nut U STEP 2 if applicable Insert lock washer V and secure nipple P onto hickey W GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX GROUND WIRE WIRE
4. oduct identifies products manu factured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy G against ceiling allowing for mounting screws I to protrude through holes in canopy G Secure in place with cap nuts F STEP 2 Raise diffuser R to fixture ring Q add rubber washer and nut if applicable Insert decorative cup O onto nipple P secure with N STEP 3 Install lamps gt v CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search