Sea Gull Lighting 75190-962 Installation Guide
Contents
1. OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors After wires are connect tuck them carefully inside outlet box Raise the canopy C to the ceiling allowing for mounting screws B to protrude through holes in canopy C Secure in place with cap D STEP 2 Install lamps and secure into clips socket clip must be mounted towards ceiling STEP 3 Place glass F on center pipe E of canopy C and secure in place trim cap G if applicable and finial l J C r ep CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts2. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully NOTE Read the instructions carefully If you are unclear as to how to proceed consult a qualified electrician GROUND WIRE WIRE CONNECTOR MOUNTING SCREWS B lt MOUNTING BAR A _ OUTLET BOX SCREWS lt CANOPY C COUPLING J B amp lt CAP NUTS D lt _ CENTER PIPE E a GLASS F lt _ CAP G FINIAL 1 NOT SUPPLIED FIGURE 1 NOTE Illustration is only intended for easy identification of parts and is in no way a representation of your particular fixture Your fixture may not use every part shown in illustration ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture WARNING FOR FIXTURES PROVIDED WITH 75 COR90 C SUPPLY WIRE WARNING ONLY THESE WARNINGS ARE PROVIDED ON THE U L LABEL AND O
3. K WITHOUT BROWN GOLD OR BLACK WITH TRACER DE NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw Z is to be inserted into the hole with two raised dimples provided on the mounting bar Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw on the mounting bar NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK
4. N THE FIXTURE CARTON WARNING RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX MOUNTING BAR A MOUNTING lt i D lt OUTLET BOX GREEN GROUNDING SCREW Z AE NOT INCLUDED FIGURE 2 sea gull lighting Installation And Safety Instruction HC 731 082103 Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 731 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 1 Thread mounting screws B in through top of mounting bar A raised side is top as illustrated Run screw threads B all the way down to the heads Secure mounting bar A to outlet box with the outlet box screws not supplied STEP 2 Thread center pipe E into coupling J until secure STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s fall into and connect the wire s according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED CJ m y WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER LSS BROWN GOLD OR BLAC
Download Pdf Manuals
Related Search